On Wed, 28 Nov 2007 23:01:31 +0300 Alexey Dobriyan <adobriyan@xxxxxxxxx> wrote: > Reliably spams dmesg with end_request() horrors. This happens when git > starts checking out linux tree to fresh ext2 partition. Disk is several > month old and there were no prolems with, say, 2.6.24-rc3: > > [ 225.378426] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.378659] end_request: I/O error, dev sdb, sector 141295703 > [ 225.390133] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.391988] end_request: I/O error, dev sdb, sector 141295703 > [ 225.392463] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.392625] end_request: I/O error, dev sdb, sector 141295703 > [ 225.392999] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.393161] end_request: I/O error, dev sdb, sector 141295703 > [ 225.393571] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.393731] end_request: I/O error, dev sdb, sector 141295703 > [ 225.394382] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.394544] end_request: I/O error, dev sdb, sector 141295703 > [ 225.395247] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.395412] end_request: I/O error, dev sdb, sector 141295703 > > CONFIG_ATA=y > # CONFIG_ATA_NONSTANDARD is not set > CONFIG_ATA_ACPI=y > CONFIG_SATA_AHCI=y > CONFIG_ATA_PIIX=y > CONFIG_PATA_JMICRON=y and > [ 35.229713] sd 2:0:1:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) So that's an OK sector number. > [ 0.000000] Linux version 2.6.24-rc3-mm2 (ad@core2) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #3 SMP PREEMPT Wed Nov 28 22:23:45 MSK 2007 > [ 0.000000] Command line: root=/dev/sda2 netconsole=@xxxxxxxxxx/eth0,9353@xxxxxxxxx/00:80:48:45:EC:73 ignore_loglevel > [ 0.000000] BIOS-provided physical RAM map: > [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) > [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff90000 (usable) > [ 0.000000] BIOS-e820: 000000007ff90000 - 000000007ff9e000 (ACPI data) > [ 0.000000] BIOS-e820: 000000007ff9e000 - 000000007ffe0000 (ACPI NVS) > [ 0.000000] BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved) > [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > [ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) > [ 0.000000] BIOS-e820: 0000000100000000 - 0000000180000000 (usable) > [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used > [ 0.000000] Entering add_active_range(0, 256, 524176) 1 entries of 256 used > [ 0.000000] Entering add_active_range(0, 1048576, 1572864) 2 entries of 256 used > [ 0.000000] end_pfn_map = 1572864 > [ 0.000000] DMI 2.4 present. > [ 0.000000] ACPI: RSDP 000FA980, 0024 (r2 ACPIAM) > [ 0.000000] ACPI: XSDT 7FF90100, 0054 (r1 KOZIRO FRONTIER 2000707 MSFT 97) > [ 0.000000] ACPI: FACP 7FF90290, 00F4 (r3 MSTEST OEMFACP 2000707 MSFT 97) > [ 0.000000] ACPI: DSDT 7FF905C0, 8FA9 (r1 A0637 A0637000 0 INTL 20060113) > [ 0.000000] ACPI: FACS 7FF9E000, 0040 > [ 0.000000] ACPI: APIC 7FF90390, 006C (r1 MSTEST OEMAPIC 2000707 MSFT 97) > [ 0.000000] ACPI: MCFG 7FF90400, 003C (r1 MSTEST OEMMCFG 2000707 MSFT 97) > [ 0.000000] ACPI: SLIC 7FF90440, 0176 (r1 KOZIRO FRONTIER 2000707 MSFT 97) > [ 0.000000] ACPI: OEMB 7FF9E040, 007B (r1 MSTEST AMI_OEM 2000707 MSFT 97) > [ 0.000000] ACPI: HPET 7FF99570, 0038 (r1 MSTEST OEMHPET 2000707 MSFT 97) > [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used > [ 0.000000] Entering add_active_range(0, 256, 524176) 1 entries of 256 used > [ 0.000000] Entering add_active_range(0, 1048576, 1572864) 2 entries of 256 used > [ 0.000000] [ffffe20000000000-ffffe200001fffff] PMD ->FFFF810001200000 on node 0 > [ 0.000000] [ffffe20000200000-ffffe200003fffff] PMD ->FFFF810001600000 on node 0 > [ 0.000000] [ffffe20000400000-ffffe200005fffff] PMD ->FFFF810001A00000 on node 0 > [ 0.000000] [ffffe20000600000-ffffe200007fffff] PMD ->FFFF810001E00000 on node 0 > [ 0.000000] [ffffe20000800000-ffffe200009fffff] PMD ->FFFF810002200000 on node 0 > [ 0.000000] [ffffe20000a00000-ffffe20000bfffff] PMD ->FFFF810002600000 on node 0 > [ 0.000000] [ffffe20000c00000-ffffe20000dfffff] PMD ->FFFF810002A00000 on node 0 > [ 0.000000] [ffffe20000e00000-ffffe20000ffffff] PMD ->FFFF810002E00000 on node 0 > [ 0.000000] [ffffe20001000000-ffffe200011fffff] PMD ->FFFF810003200000 on node 0 > [ 0.000000] [ffffe20001200000-ffffe200013fffff] PMD ->FFFF810003600000 on node 0 > [ 0.000000] [ffffe20001400000-ffffe200015fffff] PMD ->FFFF810003A00000 on node 0 > [ 0.000000] [ffffe20001600000-ffffe200017fffff] PMD ->FFFF810003E00000 on node 0 > [ 0.000000] [ffffe20001800000-ffffe200019fffff] PMD ->FFFF810004200000 on node 0 > [ 0.000000] [ffffe20001a00000-ffffe20001bfffff] PMD ->FFFF810004600000 on node 0 > [ 0.000000] [ffffe20001c00000-ffffe20001dfffff] PMD ->FFFF810004A00000 on node 0 > [ 0.000000] [ffffe20001e00000-ffffe20001ffffff] PMD ->FFFF810004E00000 on node 0 > [ 0.000000] [ffffe20002000000-ffffe200021fffff] PMD ->FFFF810005200000 on node 0 > [ 0.000000] [ffffe20002200000-ffffe200023fffff] PMD ->FFFF810005600000 on node 0 > [ 0.000000] [ffffe20002400000-ffffe200025fffff] PMD ->FFFF810005A00000 on node 0 > [ 0.000000] [ffffe20002600000-ffffe200027fffff] PMD ->FFFF810005E00000 on node 0 > [ 0.000000] [ffffe20002800000-ffffe200029fffff] PMD ->FFFF810006200000 on node 0 > [ 0.000000] [ffffe20002a00000-ffffe20002bfffff] PMD ->FFFF810006600000 on node 0 > [ 0.000000] [ffffe20002c00000-ffffe20002dfffff] PMD ->FFFF810006A00000 on node 0 > [ 0.000000] [ffffe20002e00000-ffffe20002ffffff] PMD ->FFFF810006E00000 on node 0 > [ 0.000000] [ffffe20003000000-ffffe200031fffff] PMD ->FFFF810007200000 on node 0 > [ 0.000000] [ffffe20003200000-ffffe200033fffff] PMD ->FFFF810007600000 on node 0 > [ 0.000000] [ffffe20003400000-ffffe200035fffff] PMD ->FFFF810007A00000 on node 0 > [ 0.000000] [ffffe20003600000-ffffe200037fffff] PMD ->FFFF810007E00000 on node 0 > [ 0.000000] [ffffe20003800000-ffffe200039fffff] PMD ->FFFF810008200000 on node 0 > [ 0.000000] [ffffe20003a00000-ffffe20003bfffff] PMD ->FFFF810008600000 on node 0 > [ 0.000000] [ffffe20003c00000-ffffe20003dfffff] PMD ->FFFF810008A00000 on node 0 > [ 0.000000] [ffffe20003e00000-ffffe20003ffffff] PMD ->FFFF810008E00000 on node 0 > [ 0.000000] [ffffe20004000000-ffffe200041fffff] PMD ->FFFF810009200000 on node 0 > [ 0.000000] [ffffe20004200000-ffffe200043fffff] PMD ->FFFF810009600000 on node 0 > [ 0.000000] [ffffe20004400000-ffffe200045fffff] PMD ->FFFF810009A00000 on node 0 > [ 0.000000] [ffffe20004600000-ffffe200047fffff] PMD ->FFFF810009E00000 on node 0 > [ 0.000000] [ffffe20004800000-ffffe200049fffff] PMD ->FFFF81000A200000 on node 0 > [ 0.000000] [ffffe20004a00000-ffffe20004bfffff] PMD ->FFFF81000A600000 on node 0 > [ 0.000000] [ffffe20004c00000-ffffe20004dfffff] PMD ->FFFF81000AA00000 on node 0 > [ 0.000000] [ffffe20004e00000-ffffe20004ffffff] PMD ->FFFF81000AE00000 on node 0 > [ 0.000000] [ffffe20005000000-ffffe200051fffff] PMD ->FFFF81000B200000 on node 0 > [ 0.000000] [ffffe20005200000-ffffe200053fffff] PMD ->FFFF81000B600000 on node 0 > [ 0.000000] sizeof(struct page) = 56 > [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0 -> 4096 > [ 0.000000] DMA32 4096 -> 1048576 > [ 0.000000] Normal 1048576 -> 1572864 > [ 0.000000] Movable zone start PFN for each node > [ 0.000000] early_node_map[3] active PFN ranges > [ 0.000000] 0: 0 -> 159 > [ 0.000000] 0: 256 -> 524176 > [ 0.000000] 0: 1048576 -> 1572864 > [ 0.000000] On node 0 totalpages: 1048367 > [ 0.000000] DMA zone: 56 pages used for memmap > [ 0.000000] DMA zone: 1780 pages reserved > [ 0.000000] DMA zone: 2163 pages, LIFO batch:0 > [ 0.000000] DMA32 zone: 14280 pages used for memmap > [ 0.000000] DMA32 zone: 505800 pages, LIFO batch:31 > [ 0.000000] Normal zone: 7168 pages used for memmap > [ 0.000000] Normal zone: 517120 pages, LIFO batch:31 > [ 0.000000] Movable zone: 0 pages used for memmap > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > [ 0.000000] Processor #0 (Bootup-CPU) > [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) > [ 0.000000] Processor #1 > [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) > [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > [ 0.000000] ACPI: IRQ0 used by override. > [ 0.000000] ACPI: IRQ2 used by override. > [ 0.000000] ACPI: IRQ9 used by override. > [ 0.000000] Setting APIC routing to flat > [ 0.000000] ACPI: HPET id: 0x8086a202 base: 0xfed00000 > [ 0.000000] Using ACPI (MADT) for SMP configuration information > [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7ee00000) > [ 0.000000] PERCPU: Allocating 23392 bytes of per cpu data > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1025083 > [ 0.000000] Kernel command line: root=/dev/sda2 netconsole=@xxxxxxxxxx/eth0,9353@xxxxxxxxx/00:80:48:45:EC:73 ignore_loglevel > [ 0.000000] debug: ignoring loglevel setting. > [ 0.000000] Initializing CPU#0 > [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) > [ 0.000000] Extended CMOS year: 2000 > [ 0.000000] hpet clockevent registered > [ 0.000000] TSC calibrated against HPET > [ 30.809404] time.c: Detected 2135.038 MHz processor. > [ 30.812136] Console: colour VGA+ 80x25 > [ 30.812141] console [tty0] enabled > [ 30.828153] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar > [ 30.828323] ... MAX_LOCKDEP_SUBCLASSES: 8 > [ 30.828434] ... MAX_LOCK_DEPTH: 30 > [ 30.828537] ... MAX_LOCKDEP_KEYS: 2048 > [ 30.828641] ... CLASSHASH_SIZE: 1024 > [ 30.828746] ... MAX_LOCKDEP_ENTRIES: 8192 > [ 30.828850] ... MAX_LOCKDEP_CHAINS: 16384 > [ 30.828954] ... CHAINHASH_SIZE: 8192 > [ 30.829058] memory used by lock dependency info: 1648 kB > [ 30.829169] per task-struct memory footprint: 1680 bytes > [ 30.829280] ------------------------ > [ 30.829387] | Locking API testsuite: > [ 30.829486] ---------------------------------------------------------------------------- > [ 30.831340] | spin |wlock |rlock |mutex | wsem | rsem | > [ 30.831519] -------------------------------------------------------------------------- > [ 30.831693] A-A deadlock: ok | ok | ok | ok | ok | ok | > [ 30.832704] A-B-B-A deadlock: ok | ok | ok | ok | ok | ok | > [ 30.833691] A-B-B-C-C-A deadlock: ok | ok | ok | ok | ok | ok | > [ 30.834713] A-B-C-A-B-C deadlock: ok | ok | ok | ok | ok | ok | > [ 30.835735] A-B-B-C-C-D-D-A deadlock: ok | ok | ok | ok | ok | ok | > [ 30.836799] A-B-C-D-B-D-D-A deadlock: ok | ok | ok | ok | ok | ok | > [ 30.837864] A-B-C-D-B-C-D-A deadlock: ok | ok | ok | ok | ok | ok | > [ 30.838934] double unlock: ok | ok | ok | ok | ok | ok | > [ 30.839890] initialize held: ok | ok | ok | ok | ok | ok | > [ 30.840842] bad unlock order: ok | ok | ok | ok | ok | ok | > [ 30.841834] -------------------------------------------------------------------------- > [ 30.842005] recursive read-lock: | ok | | ok | > [ 30.842533] recursive read-lock #2: | ok | | ok | > [ 30.843054] mixed read-write-lock: | ok | | ok | > [ 30.843587] mixed write-read-lock: | ok | | ok | > [ 30.844111] -------------------------------------------------------------------------- > [ 30.844282] hard-irqs-on + irq-safe-A/12: ok | ok | ok | > [ 30.844810] soft-irqs-on + irq-safe-A/12: ok | ok | ok | > [ 30.845330] hard-irqs-on + irq-safe-A/21: ok | ok | ok | > [ 30.845859] soft-irqs-on + irq-safe-A/21: ok | ok | ok | > [ 30.846388] sirq-safe-A => hirqs-on/12: ok | ok | ok | > [ 30.846909] sirq-safe-A => hirqs-on/21: ok | ok | ok | > [ 30.847439] hard-safe-A + irqs-on/12: ok | ok | ok | > [ 30.847958] soft-safe-A + irqs-on/12: ok | ok | ok | > [ 30.848489] hard-safe-A + irqs-on/21: ok | ok | ok | > [ 30.849010] soft-safe-A + irqs-on/21: ok | ok | ok | > [ 30.849540] hard-safe-A + unsafe-B #1/123: ok | ok | ok | > [ 30.850074] soft-safe-A + unsafe-B #1/123: ok | ok | ok | > [ 30.850617] hard-safe-A + unsafe-B #1/132: ok | ok | ok | > [ 30.851151] soft-safe-A + unsafe-B #1/132: ok | ok | ok | > [ 30.851693] hard-safe-A + unsafe-B #1/213: ok | ok | ok | > [ 30.852228] soft-safe-A + unsafe-B #1/213: ok | ok | ok | > [ 30.852771] hard-safe-A + unsafe-B #1/231: ok | ok | ok | > [ 30.853301] soft-safe-A + unsafe-B #1/231: ok | ok | ok | > [ 30.853842] hard-safe-A + unsafe-B #1/312: ok | ok | ok | > [ 30.854373] soft-safe-A + unsafe-B #1/312: ok | ok | ok | > [ 30.854897] hard-safe-A + unsafe-B #1/321: ok | ok | ok | > [ 30.855435] soft-safe-A + unsafe-B #1/321: ok | ok | ok | > [ 30.855967] hard-safe-A + unsafe-B #2/123: ok | ok | ok | > [ 30.856506] soft-safe-A + unsafe-B #2/123: ok | ok | ok | > [ 30.857040] hard-safe-A + unsafe-B #2/132: ok | ok | ok | > [ 30.857578] soft-safe-A + unsafe-B #2/132: ok | ok | ok | > [ 30.858112] hard-safe-A + unsafe-B #2/213: ok | ok | ok | > [ 30.858651] soft-safe-A + unsafe-B #2/213: ok | ok | ok | > [ 30.859184] hard-safe-A + unsafe-B #2/231: ok | ok | ok | > [ 30.859720] soft-safe-A + unsafe-B #2/231: ok | ok | ok | > [ 30.860251] hard-safe-A + unsafe-B #2/312: ok | ok | ok | > [ 30.860788] soft-safe-A + unsafe-B #2/312: ok | ok | ok | > [ 30.861331] hard-safe-A + unsafe-B #2/321: ok | ok | ok | > [ 30.861858] soft-safe-A + unsafe-B #2/321: ok | ok | ok | > [ 30.862397] hard-irq lock-inversion/123: ok | ok | ok | > [ 30.862927] soft-irq lock-inversion/123: ok | ok | ok | > [ 30.863469] hard-irq lock-inversion/132: ok | ok | ok | > [ 30.863998] soft-irq lock-inversion/132: ok | ok | ok | > [ 30.864541] hard-irq lock-inversion/213: ok | ok | ok | > [ 30.865073] soft-irq lock-inversion/213: ok | ok | ok | > [ 30.865616] hard-irq lock-inversion/231: ok | ok | ok | > [ 30.866145] soft-irq lock-inversion/231: ok | ok | ok | > [ 30.866686] hard-irq lock-inversion/312: ok | ok | ok | > [ 30.867216] soft-irq lock-inversion/312: ok | ok | ok | > [ 30.867760] hard-irq lock-inversion/321: ok | ok | ok | > [ 30.868288] soft-irq lock-inversion/321: ok | ok | ok | > [ 30.868828] hard-irq read-recursion/123: ok | > [ 30.869097] soft-irq read-recursion/123: ok | > [ 30.869376] hard-irq read-recursion/132: ok | > [ 30.869646] soft-irq read-recursion/132: ok | > [ 30.869916] hard-irq read-recursion/213: ok | > [ 30.870185] soft-irq read-recursion/213: ok | > [ 30.870464] hard-irq read-recursion/231: ok | > [ 30.870733] soft-irq read-recursion/231: ok | > [ 30.871003] hard-irq read-recursion/312: ok | > [ 30.871272] soft-irq read-recursion/312: ok | > [ 30.871550] hard-irq read-recursion/321: ok | > [ 30.871819] soft-irq read-recursion/321: ok | > [ 30.872089] ------------------------------------------------------- > [ 30.872205] Good, all 218 testcases passed! | > [ 30.872318] --------------------------------- > [ 30.874334] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) > [ 30.877360] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) > [ 30.877811] Checking aperture... > [ 30.877916] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) > [ 30.908946] Placing software IO TLB between 0xbe61000 - 0xfe61000 > [ 30.946667] Memory: 4026948k/6291456k available (2044k kernel code, 165884k reserved, 816k data, 200k init) > [ 30.946915] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 > [ 31.006137] Calibrating delay using timer specific routine.. 4273.18 BogoMIPS (lpj=2136592) > [ 31.006412] Mount-cache hash table entries: 256 > [ 31.007012] CPU: L1 I cache: 32K, L1 D cache: 32K > [ 31.007162] CPU: L2 cache: 2048K > [ 31.007261] using mwait in idle threads. > [ 31.007362] CPU: Physical Processor ID: 0 > [ 31.007465] CPU: Processor Core ID: 0 > [ 31.007570] CPU0: Thermal monitoring enabled (TM2) > [ 31.007691] Freeing SMP alternatives: 16k freed > [ 31.008231] ACPI: Core revision 20070126 > [ 31.057639] Using local APIC timer interrupts. > [ 31.104537] APIC timer calibration result 16679981 > [ 31.104645] Detected 16.679 MHz APIC timer. > [ 31.104934] lockdep: not fixing up alternatives. > [ 31.105102] Booting processor 1/2 APIC 0x1 > [ 31.115410] Initializing CPU#1 > [ 31.175659] Calibrating delay using timer specific routine.. 4269.88 BogoMIPS (lpj=2134942) > [ 31.175665] CPU: L1 I cache: 32K, L1 D cache: 32K > [ 31.175666] CPU: L2 cache: 2048K > [ 31.175668] CPU: Physical Processor ID: 0 > [ 31.175670] CPU: Processor Core ID: 1 > [ 31.175676] CPU1: Thermal monitoring enabled (TM2) > [ 31.175960] Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 02 > [ 31.176018] checking TSC synchronization [CPU#0 -> CPU#1]: passed. > [ 31.197049] Brought up 2 CPUs > [ 31.197767] net_namespace: 208 bytes > [ 31.198257] NET: Registered protocol family 16 > [ 31.198913] ACPI: bus type pci registered > [ 31.199020] PCI: Using configuration type 1 > [ 31.211197] ACPI: EC: Look up EC in DSDT > [ 31.244080] ACPI: Interpreter enabled > [ 31.244181] ACPI: (supports S0 S5) > [ 31.244374] ACPI: Using IOAPIC for interrupt routing > [ 31.274684] ACPI: PCI Root Bridge [PCI0] (0000:00) > [ 31.275862] PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO > [ 31.275982] PCI quirk: region 0480-04bf claimed by ICH6 GPIO > [ 31.276928] PCI: Transparent bridge - 0000:00:1e.0 > [ 31.277111] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > [ 31.278473] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] > [ 31.278914] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] > [ 31.279752] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] > [ 31.280204] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT] > [ 31.280644] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] > [ 31.331552] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) > [ 31.332346] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15) > [ 31.333141] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15) > [ 31.333939] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15) > [ 31.334733] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. > [ 31.335644] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. > [ 31.336556] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15) > [ 31.337344] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 *14 15) > [ 31.338112] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 08, should be FB [20070126] > [ 31.338369] Linux Plug and Play Support v0.97 (c) Adam Belay > [ 31.338597] pnp: PnP ACPI init > [ 31.338717] ACPI: bus type pnp registered > [ 31.345055] pnp 00:09: can't allocate MMIO space at 0xffafe000 > [ 31.351967] pnp: PnP ACPI: found 16 devices > [ 31.352072] ACPI: ACPI bus type pnp unregistered > [ 31.352790] SCSI subsystem initialized > [ 31.352980] libata version 3.00 loaded. > [ 31.353334] PCI: Using ACPI for IRQ routing > [ 31.353442] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report > [ 31.356582] PCI-GART: No AMD northbridge found. > [ 31.357487] Time: tsc clocksource has been installed. > [ 31.359656] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved > [ 31.359802] system 00:08: ioport range 0x290-0x297 has been reserved > [ 31.361619] system 00:09: ioport range 0x4d0-0x4d1 has been reserved > [ 31.361738] system 00:09: ioport range 0x800-0x87f has been reserved > [ 31.361856] system 00:09: ioport range 0x480-0x4bf has been reserved > [ 31.361976] system 00:09: iomem range 0xffafe000-0xffb0cbff could not be reserved > [ 31.362147] system 00:09: iomem range 0xffb00000-0xffbfffff could not be reserved > [ 31.362316] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved > [ 31.362446] system 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved > [ 31.362575] system 00:09: iomem range 0xfff00000-0xfffffffe could not be reserved > [ 31.362744] system 00:09: iomem range 0xfebfe000-0xfebfec00 has been reserved > [ 31.362876] system 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved > [ 31.363007] system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved > [ 31.363184] system 00:0e: iomem range 0xe0000000-0xefffffff has been reserved > [ 31.363322] system 00:0f: iomem range 0x0-0x9ffff could not be reserved > [ 31.363442] system 00:0f: iomem range 0xc0000-0xcffff has been reserved > [ 31.363568] system 00:0f: iomem range 0xe0000-0xfffff could not be reserved > [ 31.363693] system 00:0f: iomem range 0x100000-0x7fffffff could not be reserved > [ 31.363864] system 00:0f: iomem range 0x0-0x0 could not be reserved > [ 31.365299] PCI: Bridge: 0000:00:01.0 > [ 31.365401] IO window: a000-afff > [ 31.365502] MEM window: f8800000-fe8fffff > [ 31.365618] PREFETCH window: bfe00000-dfdfffff > [ 31.365726] PCI: Bridge: 0000:00:1c.0 > [ 31.365826] IO window: disabled. > [ 31.365928] MEM window: disabled. > [ 31.366029] PREFETCH window: dfe00000-dfefffff > [ 31.366139] PCI: Bridge: 0000:00:1c.3 > [ 31.366238] IO window: disabled. > [ 31.366340] MEM window: fea00000-feafffff > [ 31.366445] PREFETCH window: disabled. > [ 31.366553] PCI: Bridge: 0000:00:1c.4 > [ 31.366654] IO window: b000-bfff > [ 31.366756] MEM window: fe900000-fe9fffff > [ 31.366861] PREFETCH window: disabled. > [ 31.366966] PCI: Bridge: 0000:00:1e.0 > [ 31.367066] IO window: disabled. > [ 31.367167] MEM window: disabled. > [ 31.367268] PREFETCH window: disabled. > [ 31.367389] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 > [ 31.367597] PCI: Setting latency timer of device 0000:00:01.0 to 64 > [ 31.367732] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 > [ 31.367936] PCI: Setting latency timer of device 0000:00:1c.0 to 64 > [ 31.368072] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19 > [ 31.368276] PCI: Setting latency timer of device 0000:00:1c.3 to 64 > [ 31.368410] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16 > [ 31.368617] PCI: Setting latency timer of device 0000:00:1c.4 to 64 > [ 31.368743] PCI: Setting latency timer of device 0000:00:1e.0 to 64 > [ 31.368876] NET: Registered protocol family 2 > [ 31.378818] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) > [ 31.379519] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) > [ 31.381487] TCP bind hash table entries: 65536 (order: 9, 3670016 bytes) > [ 31.386055] TCP: Hash tables configured (established 262144 bind 65536) > [ 31.386204] TCP reno registered > [ 31.403547] io scheduler noop registered > [ 31.404080] io scheduler cfq registered (default) > [ 31.406028] Boot video device is 0000:01:00.0 > [ 31.409155] Switched to high resolution mode on CPU 1 > [ 31.409732] Switched to high resolution mode on CPU 0 > [ 31.414361] Real Time Clock Driver v1.12ac > [ 31.414465] Linux agpgart interface v0.103 > [ 31.414852] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 19 > [ 31.415061] PCI: Setting latency timer of device 0000:03:00.0 to 64 > [ 31.415597] atl1 0000:03:00.0: version 2.0.7 > [ 31.451060] netconsole: local port 6665 > [ 31.451162] netconsole: local IP 10.10.0.42 > [ 31.451265] netconsole: interface eth0 > [ 31.451365] netconsole: remote port 9353 > [ 31.451467] netconsole: remote IP 10.10.0.1 > [ 31.451571] netconsole: remote ethernet address 00:80:48:45:ec:73 > [ 31.451696] netconsole: device eth0 not up yet, forcing it > [ 32.955843] atl1 0000:03:00.0: eth0 link is up 100 Mbps full duplex > [ 32.959943] console [netcon0] enabled > [ 33.009788] netconsole: network logging started > [ 33.012043] ahci 0000:02:00.0: version 3.0 > [ 33.012187] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 > [ 34.012514] ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode > [ 34.012699] ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part > [ 34.012834] PCI: Setting latency timer of device 0000:02:00.0 to 64 > [ 34.013333] scsi0 : ahci > [ 34.013616] scsi1 : ahci > [ 34.014002] ata1: SATA max UDMA/133 abar m8192@0xfe9fe000 port 0xfe9fe100 irq 16 > [ 34.014174] ata2: SATA max UDMA/133 abar m8192@0xfe9fe000 port 0xfe9fe180 irq 16 > [ 34.318163] ata1: SATA link down (SStatus 0 SControl 300) > [ 34.622817] ata2: SATA link down (SStatus 0 SControl 300) > [ 34.623116] ata_piix 0000:00:1f.2: version 2.12 > [ 34.623230] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] > [ 34.623553] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 > [ 34.623796] PCI: Setting latency timer of device 0000:00:1f.2 to 64 > [ 34.623976] scsi2 : ata_piix > [ 34.624244] scsi3 : ata_piix > [ 34.636578] ata3: SATA max UDMA/133 cmd 0xec00 ctl 0xe880 bmdma 0xe400 irq 19 > [ 34.636705] ata4: SATA max UDMA/133 cmd 0xe800 ctl 0xe480 bmdma 0xe408 irq 19 > [ 34.839027] ata3.00: ATA-7: ST3250620AS, 3.AAE, max UDMA/133 > [ 34.839149] ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32) > [ 34.869628] ata3.01: ATA-7: ST3500630AS, 3.AAK, max UDMA/133 > [ 34.869747] ata3.01: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) > [ 34.905567] ata3.00: configured for UDMA/133 > [ 34.944500] ata3.01: configured for UDMA/133 > [ 35.130121] ata4.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133 > [ 35.130256] ata4.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32) > [ 35.204995] ata4.00: configured for UDMA/133 > [ 35.205453] scsi 2:0:0:0: Direct-Access ATA ST3250620AS 3.AA PQ: 0 ANSI: 5 > [ 35.206071] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) > [ 35.206221] sd 2:0:0:0: [sda] Write Protect is off > [ 35.206333] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 35.206496] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 35.206946] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) > [ 35.207096] sd 2:0:0:0: [sda] Write Protect is off > [ 35.207207] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 35.207370] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 35.207564] sda: sda1 sda2 sda3 sda4 > [ 35.228877] sd 2:0:0:0: [sda] Attached SCSI disk > [ 35.229235] scsi 2:0:1:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 > [ 35.229713] sd 2:0:1:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) > [ 35.229862] sd 2:0:1:0: [sdb] Write Protect is off > [ 35.229974] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 > [ 35.230133] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 35.230430] sd 2:0:1:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) > [ 35.230580] sd 2:0:1:0: [sdb] Write Protect is off > [ 35.230692] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00 > [ 35.230852] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 35.231036] sdb: sdb1 > [ 35.250751] sd 2:0:1:0: [sdb] Attached SCSI disk > [ 35.251164] scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 > [ 35.251651] sd 3:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB) > [ 35.251807] sd 3:0:0:0: [sdc] Write Protect is off > [ 35.251918] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 > [ 35.252090] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 35.252393] sd 3:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB) > [ 35.252549] sd 3:0:0:0: [sdc] Write Protect is off > [ 35.252666] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 > [ 35.252832] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 35.253020] sdc: sdc1 > [ 35.269976] sd 3:0:0:0: [sdc] Attached SCSI disk > [ 35.270221] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] > [ 35.270556] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 19 > [ 35.270816] PCI: Setting latency timer of device 0000:00:1f.5 to 64 > [ 35.271012] scsi4 : ata_piix > [ 35.271291] scsi5 : ata_piix > [ 35.278657] ata5: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xc880 irq 19 > [ 35.278783] ata6: SATA max UDMA/133 cmd 0xd000 ctl 0xcc00 bmdma 0xc888 irq 19 > [ 35.610898] ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 17 (level, low) -> IRQ 17 > [ 35.611159] PCI: Setting latency timer of device 0000:02:00.1 to 64 > [ 35.611347] scsi6 : pata_jmicron > [ 35.611627] scsi7 : pata_jmicron > [ 35.614721] ata7: PATA max UDMA/100 cmd 0xbc00 ctl 0xb880 bmdma 0xb400 irq 17 > [ 35.614847] ata8: PATA max UDMA/100 cmd 0xb800 ctl 0xb480 bmdma 0xb408 irq 17 > [ 36.069763] ata7.01: ATAPI: _NEC DV-5800C, D9S2, max UDMA/33 > [ 36.220633] ata7.01: configured for UDMA/33 > [ 36.404203] scsi 6:0:1:0: CD-ROM _NEC DV-5800C D9S2 PQ: 0 ANSI: 5 > [ 36.407494] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray > [ 36.407620] Uniform CD-ROM driver Revision: 3.20 > [ 36.408021] sr 6:0:1:0: Attached scsi CD-ROM sr0 > [ 36.408481] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 > [ 36.408601] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp > [ 36.409362] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 36.409681] TCP cubic registered > [ 36.410085] NET: Registered protocol family 1 > [ 36.430531] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 > [ 36.517238] EXT3-fs: INFO: recovery required on readonly filesystem. > [ 36.517363] EXT3-fs: write access will be enabled during recovery. > [ 36.543412] kjournald starting. Commit interval 5 seconds > [ 36.543577] EXT3-fs: recovery complete. > [ 36.544251] EXT3-fs: mounted filesystem with ordered data mode. > [ 36.544426] VFS: Mounted root (ext3 filesystem) readonly. > [ 36.544610] Freeing unused kernel memory: 200k freed > [ 36.545338] Write protecting the kernel read-only data: 2644k > [ 38.568379] EXT3 FS on sda2, internal journal > [ 38.695881] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended > [ 38.714694] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended > [ 38.749809] Adding 7823644k swap on /dev/sda3. Priority:-1 extents:1 across:7823644k > [ 225.378426] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.378659] end_request: I/O error, dev sdb, sector 141295703 > [ 225.390133] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.391988] end_request: I/O error, dev sdb, sector 141295703 > [ 225.392463] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.392625] end_request: I/O error, dev sdb, sector 141295703 > [ 225.392999] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.393161] end_request: I/O error, dev sdb, sector 141295703 > [ 225.393571] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.393731] end_request: I/O error, dev sdb, sector 141295703 > [ 225.394382] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.394544] end_request: I/O error, dev sdb, sector 141295703 > [ 225.395247] sd 2:0:1:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00 > [ 225.395412] end_request: I/O error, dev sdb, sector 141295703 I don't know whether this failure was a scsi thing or an ata thing? - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
