Does 2.6.24-rc3 support SATA port multipliers?
I am getting "ata6.03: COMRESET failed (errno=-5)" error messages with a
SiliconImage PMP connected to an Intel ICH9 SATA controller in AHCI
mode.
Dmesg output attached.
Thanks,
Jason
Linux version 2.6.24-rc3 (root@xxxxxxxxxxxxxxxxxxxxx) (gcc version 4.1.2 20070626 (Red Hat 4.1.2-14)) #1 SMP Tue Nov 20 17:43:24 PST 2007
Command line: ro root=/dev/VolGroup00/LogVol00 pci=nommconf rhgb quiet
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c000 (usable)
BIOS-e820: 000000000009c000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007d3a0000 (usable)
BIOS-e820: 000000007d3a0000 - 000000007d3ae000 (ACPI data)
BIOS-e820: 000000007d3ae000 - 000000007d3f0000 (ACPI NVS)
BIOS-e820: 000000007d3f0000 - 000000007d700000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffa6b000 - 00000000ffa6c000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 156) 0 entries of 3200 used
Entering add_active_range(0, 256, 512928) 1 entries of 3200 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F93C0, 0014 (r0 ACPIAM)
ACPI: RSDT 7D3A0000, 0044 (r1 080107 RSDT1024 20070801 MSFT 97)
ACPI: FACP 7D3A0200, 0084 (r2 080107 FACP1024 20070801 MSFT 97)
ACPI: DSDT 7D3A0490, 687F (r1 VVBLI9 VVBLI958 58 INTL 20051117)
ACPI: FACS 7D3AE000, 0040
ACPI: APIC 7D3A0390, 006C (r1 080107 APIC1024 20070801 MSFT 97)
ACPI: MCFG 7D3A0450, 003C (r1 080107 OEMMCFG 20070801 MSFT 97)
ACPI: OEMB 7D3AE040, 008A (r1 080107 OEMB1024 20070801 MSFT 97)
ACPI: ASF! 7D3A6D10, 0099 (r32 LEGEND I865PASF 1 INTL 20051117)
ACPI: GSCI 7D3AE0D0, 2024 (r1 080107 GMCHSCI 20070801 MSFT 97)
ACPI: iEIT 7D3B0100, 00B0 (r1 080107 EITTABLE 20070801 MSFT 97)
ACPI: SSDT 7D3B0C90, 0877 (r1 DpgPmm CpuPm 12 INTL 20051117)
No NUMA configuration found
Faking a node at 0000000000000000-000000007d3a0000
Entering add_active_range(0, 0, 156) 0 entries of 3200 used
Entering add_active_range(0, 256, 512928) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000007d3a0000
[ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
[ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
[ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0
[ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0
[ffffe20000800000-ffffe200009fffff] PMD ->ffff810002200000 on node 0
[ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002600000 on node 0
[ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002a00000 on node 0
[ffffe20000e00000-ffffe20000ffffff] PMD ->ffff810002e00000 on node 0
[ffffe20001000000-ffffe200011fffff] PMD ->ffff810003200000 on node 0
[ffffe20001200000-ffffe200013fffff] PMD ->ffff810003600000 on node 0
[ffffe20001400000-ffffe200015fffff] PMD ->ffff810003a00000 on node 0
[ffffe20001600000-ffffe200017fffff] PMD ->ffff810003e00000 on node 0
[ffffe20001800000-ffffe200019fffff] PMD ->ffff810004200000 on node 0
[ffffe20001a00000-ffffe20001bfffff] PMD ->ffff810004600000 on node 0
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 156
0: 256 -> 512928
On node 0 totalpages: 512828
DMA zone: 56 pages used for memmap
DMA zone: 1952 pages reserved
DMA zone: 1988 pages, LIFO batch:0
DMA32 zone: 6956 pages used for memmap
DMA32 zone: 501876 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 7d700000:81700000)
SMP: Allowing 4 CPUs, 2 hotplug CPUs
PERCPU: Allocating 63928 bytes of per cpu data
Built 1 zonelists in Node order, mobility grouping on. Total pages: 503864
Policy zone: DMA32
Kernel command line: ro root=/dev/VolGroup00/LogVol00 pci=nommconf rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC calibrated against PM_TIMER
time.c: Detected 2992.493 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
Memory: 2011076k/2051712k available (2496k kernel code, 40236k reserved, 1188k data, 280k init)
Calibrating delay using timer specific routine.. 5988.10 BogoMIPS (lpj=2994052)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 20781203
Detected 20.781 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 5984.96 BogoMIPS (lpj=2992483)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000001 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000002
domain 1: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
CPU1 attaching sched-domain:
domain 0: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000002 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000001
domain 1: span 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups: 00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
net_namespace: 120 bytes
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: System BIOS is requesting _OSI(Linux)
ACPI: If "acpi_osi=Linux" works better,
Please send dmidecode to linux-acpi@xxxxxxxxxxxxxxx
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S5)
ACPI: Using IOAPIC for interrupt routing
Error attaching device data
Error attaching device data
Error attaching device data
Error attaching device data
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 12 *14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 12 14 *15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 12 14 *15)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 75, should be 66 [20070126]
ACPI Warning (tbutils-0217): Incorrect checksum in table [iEIT] - 89, should be C4 [20070126]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 23 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI-GART: No AMD northbridge found.
Time: tsc clocksource has been installed.
system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
system 00:0a: ioport range 0xa20-0xa3f has been reserved
system 00:0a: ioport range 0xa00-0xa0f has been reserved
system 00:0a: ioport range 0xa10-0xa1f has been reserved
system 00:0a: ioport range 0xa40-0xa5f has been reserved
system 00:0b: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:0b: iomem range 0xfed20000-0xfed8ffff has been reserved
system 00:0e: iomem range 0xffc00000-0xffefffff could not be reserved
system 00:0f: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0f: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:10: iomem range 0xe0000000-0xefffffff has been reserved
system 00:11: iomem range 0xffa6b000-0xffa6bfff could not be reserved
system 00:12: iomem range 0x0-0x0 could not be reserved
system 00:13: iomem range 0x0-0x0 could not be reserved
system 00:14: iomem range 0x0-0x0 could not be reserved
system 00:15: iomem range 0x0-0x0 could not be reserved
system 00:16: iomem range 0x0-0x9ffff could not be reserved
system 00:16: iomem range 0xc0000-0xcffff has been reserved
system 00:16: iomem range 0xe0000-0xfffff could not be reserved
system 00:16: iomem range 0x100000-0x7d3fffff could not be reserved
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3092k freed
audit: initializing netlink socket (disabled)
audit(1195646601.391:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: SSDT 7D3B01B0, 0359 (r1 DpgPmm P001Ist 11 INTL 20051117)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: SSDT 7D3B0720, 0359 (r1 DpgPmm P002Ist 12 INTL 20051117)
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI Exception (processor_core-0813): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0813): AE_NOT_FOUND, Processor Device is not present [20070126]
Marking TSC unstable due to possible TSC halt in C2
Time: acpi_pm clocksource has been installed.
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
agpgart: Detected an Intel G33 Chipset.
agpgart: Detected 7164K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: PCI Interrupt 0000:00:03.3[B] -> GSI 17 (level, low) -> IRQ 17
0000:00:03.3: ttyS2 at I/O 0xe000 (irq = 17) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
registered taskstats version 1
Freeing unused kernel memory: 280k freed
Write protecting the kernel read-only data: 872k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000d880
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000d800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1a.2 to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000d480
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d080
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.2: irq 16, io base 0x0000d000
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:1a.7[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7
usb 4-1: new low speed USB device using uhci_hcd and address 2
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 19, io mem 0xffa7b400
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa7b000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 6 ports detected
SCSI subsystem initialized
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
usb 4-1: device not accepting address 2, error -71
usb 4-1: new low speed USB device using uhci_hcd and address 4
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports ? Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf stag led clo pmp pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0xffa78800 port 0xffa78900 irq 8415
ata2: SATA max UDMA/133 abar m2048@0xffa78800 port 0xffa78980 irq 8415
ata3: SATA max UDMA/133 abar m2048@0xffa78800 port 0xffa78a00 irq 8415
ata4: SATA max UDMA/133 abar m2048@0xffa78800 port 0xffa78a80 irq 8415
ata5: SATA max UDMA/133 abar m2048@0xffa78800 port 0xffa78b00 irq 8415
ata6: SATA max UDMA/133 abar m2048@0xffa78800 port 0xffa78b80 irq 8415
usb 4-1: configuration #1 chosen from 1 choice
input: NOVATEK ORTEK USB Keyboard as /class/input/input0
input: USB HID v1.00 Keyboard [NOVATEK ORTEK USB Keyboard] on usb-0000:00:1d.0-1
input: NOVATEK ORTEK USB Keyboard as /class/input/input1
input: USB HID v1.00 Mouse [NOVATEK ORTEK USB Keyboard] on usb-0000:00:1d.0-1
usb 5-1: new low speed USB device using uhci_hcd and address 2
usb 5-1: configuration #1 chosen from 1 choice
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input2
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.1-1
ata1.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATAPI: LITE-ON DVDRW LH-20A1S, 9L03, max UDMA/100, ATAPI AN
ata2.00: configured for UDMA/100
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports, feat 0x1/0x9
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.03: failed to read SCR 2 (Emask=0x40)
ata6.03: hard resetting link
ata6.03: failed to read SCR 2 (Emask=0x40)
ata6.03: failed to read SCR 2 (Emask=0x40)
ata6.03: COMRESET failed (errno=-5)
ata6.03: failed to read SCR 0 (Emask=0x40)
ata6.03: reset failed, giving up
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.03: failed to read SCR 2 (Emask=0x40)
ata6.03: hard resetting link
ata6.03: failed to read SCR 2 (Emask=0x40)
ata6.03: failed to read SCR 2 (Emask=0x40)
ata6.03: COMRESET failed (errno=-5)
ata6.03: failed to read SCR 0 (Emask=0x40)
ata6.03: reset failed, giving up
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.03: failed to read SCR 2 (Emask=0x40)
ata6.03: hard resetting link
ata6.03: failed to read SCR 2 (Emask=0x40)
ata6.03: failed to read SCR 2 (Emask=0x40)
ata6.03: COMRESET failed (errno=-5)
ata6.03: failed to read SCR 0 (Emask=0x40)
ata6.03: reset failed, giving up
ata6.03: failed to recover link after 3 tries, disabling
ata6: failed to recover PMP, retrying in 5 secs
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.04: failed to read SCR 2 (Emask=0x40)
ata6.04: hard resetting link
ata6.04: failed to read SCR 2 (Emask=0x40)
ata6.04: failed to read SCR 2 (Emask=0x40)
ata6.04: COMRESET failed (errno=-5)
ata6.04: failed to read SCR 0 (Emask=0x40)
ata6.04: reset failed, giving up
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.04: failed to read SCR 2 (Emask=0x40)
ata6.04: hard resetting link
ata6.04: failed to read SCR 2 (Emask=0x40)
ata6.04: failed to read SCR 2 (Emask=0x40)
ata6.04: COMRESET failed (errno=-5)
ata6.04: failed to read SCR 0 (Emask=0x40)
ata6.04: reset failed, giving up
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.04: failed to read SCR 2 (Emask=0x40)
ata6.04: hard resetting link
ata6.04: failed to read SCR 2 (Emask=0x40)
ata6.04: failed to read SCR 2 (Emask=0x40)
ata6.04: COMRESET failed (errno=-5)
ata6.04: failed to read SCR 0 (Emask=0x40)
ata6.04: reset failed, giving up
ata6.04: failed to recover link after 3 tries, disabling
ata6: failed to recover PMP, retrying in 5 secs
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.05: hard resetting link
ata6.05: failed to read SCR 2 (Emask=0x40)
ata6.05: failed to read SCR 2 (Emask=0x40)
ata6.05: COMRESET failed (errno=-5)
ata6.05: failed to read SCR 0 (Emask=0x40)
ata6.05: reset failed, giving up
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.05: hard resetting link
ata6.05: failed to read SCR 2 (Emask=0x40)
ata6.05: failed to read SCR 2 (Emask=0x40)
ata6.05: COMRESET failed (errno=-5)
ata6.05: failed to read SCR 0 (Emask=0x40)
ata6.05: reset failed, giving up
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.05: hard resetting link
ata6.05: failed to read SCR 2 (Emask=0x40)
ata6.05: failed to read SCR 2 (Emask=0x40)
ata6.05: COMRESET failed (errno=-5)
ata6.05: failed to read SCR 0 (Emask=0x40)
ata6.05: reset failed, giving up
ata6.05: failed to recover link after 3 tries, disabling
ata6: failed to recover PMP, retrying in 5 secs
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata6.00: failed to recover link after 3 tries, disabling
ata6: failed to recover PMP, retrying in 5 secs
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.01: failed to IDENTIFY (I/O error, err_mask=0x40)
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.01: failed to IDENTIFY (I/O error, err_mask=0x40)
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.02: hard resetting link
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 1 (Emask=0x40)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.01: failed to IDENTIFY (I/O error, err_mask=0x40)
ata6.01: failed to recover link after 3 tries, disabling
ata6: failed to recover PMP after 5 tries, giving up
ata6.15: Port Multiplier detaching
ata6.00: disabled
ata6: exception Emask 0x10 SAct 0x0 SErr 0x800000 action 0x2 frozen t4
ata6: irq_stat 0x08000000, interface fatal error
ata6: SError: { LinkSeq }
ata6: hard resetting link
ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6: EH complete
scsi 0:0:0:0: Direct-Access ATA ST380815AS 3.AA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1S 9L03 PQ: 0 ANSI: 5
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@xxxxxxxxxx
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1195646684.803:2): enforcing=1 old_enforcing=0 auid=4294967295
SELinux:8192 avtab hash slots allocated.Num of rules:57675
SELinux:8192 avtab hash slots allocated.Num of rules:57675
security: 3 users, 6 roles, 1658 types, 210 bools, 1 sens, 1024 cats
security: 61 classes, 57675 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for labeling
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: policy loaded with handle_unknown=deny
audit(1195646685.060:3): policy loaded auid=4294967295
e1000e: Intel(R) PRO/1000 Network Driver - 0.2.0
e1000e: Copyright (c) 1999-2007 Intel Corporation.
ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:19.0 to 64
parport_pc 00:09: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 88:88:88:88:87:88
0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
0000:00:19.0: eth0: MAC: 5, PHY: 6, PBA No: ffffff-0ff
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
input: PC Speaker as /class/input/input5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
FDC 0 is a National Semiconductor PC87306
lp0: using parport0 (interrupt-driven).
lp0: console ready
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx>
warning: process `kudzu' used the deprecated sysctl system call with 1.23.
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
ADDRCONF(NETDEV_UP): eth0: link is not ready
audit(1195675509.754:4): audit_pid=2696 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized i915 1.6.0 20060119 on minor 0
set status page addr 0x0ffe1000
usb 7-2: new high speed USB device using ehci_hcd and address 2
usb 7-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 6:0:0:0: Direct-Access SanDisk U3 Titanium 2.18 PQ: 0 ANSI: 2
sd 6:0:0:0: [sdb] 4013713 512-byte hardware sectors (2055 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sd 6:0:0:0: [sdb] 4013713 512-byte hardware sectors (2055 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sdb: unknown partition table
sd 6:0:0:0: [sdb] Attached SCSI removable disk
sd 6:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
SELinux: initialized (dev sdb, type vfat), uses genfs_contexts
