Hello, Latest git, insert a CF card into cardbus slot gives: pccard: PCMCIA card inserted into slot 0 cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcffff 0xe0000-0xfffff cs: memory probe 0x60000000-0x60ffffff: clean. cs: memory probe 0xa0000000-0xa0ffffff: clean. cs: memory probe 0xdea00000-0xdeafffff: excluding 0xdea00000-0xdeafffff cs: memory probe 0xff600000-0xff6fffff: excluding 0xff600000-0xff60ffff 0xff6a0000-0xff6dffff 0xff6f0000-0xff6fffff pcmcia: registering new device pcmcia0.0 irq 9: nobody cared (try booting with the "irqpoll" option) [<c01041f2>] show_trace_log_lvl+0x1a/0x2f [<c01042ed>] show_trace+0x12/0x14 [<c0104ea0>] dump_stack+0x15/0x17 [<c0133b48>] __report_bad_irq+0x39/0x79 [<c0133d80>] note_interrupt+0x1f8/0x234 [<c0134527>] handle_level_irq+0x8e/0xd1 [<c0105a6d>] do_IRQ+0x92/0xad [<c0103f57>] common_interrupt+0x23/0x28 [<c0134513>] handle_level_irq+0x7a/0xd1 [<c0105a5e>] do_IRQ+0x83/0xad ======================= handlers: [<c02a8a38>] (acpi_irq+0x0/0x18) [<c03268e0>] (yenta_interrupt+0x0/0xb7) [<c032b1d7>] (usb_hcd_irq+0x0/0x51) [<c032b1d7>] (usb_hcd_irq+0x0/0x51) [<c032b1d7>] (usb_hcd_irq+0x0/0x51) [<c037c08c>] (snd_intel8x0_interrupt+0x0/0x1e8) [<c02eeaff>] (e1000_intr+0x0/0xeb) Disabling IRQ #9 scsi2 : pata_pcmcia ata3: PATA max PIO0 cmd 0x0001d100 ctl 0x0001d10e bmdma 0x00000000 irq 9 ata3.00: qc timeout (cmd 0x91) ata3.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x4) However, if I rename pata_pcmcia.ko so that udev cannot autoload it, insert the card and manually load pata_pcmcia.ko it works: pccard: PCMCIA card inserted into slot 0 cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcffff 0xe0000-0xfffff cs: memory probe 0x60000000-0x60ffffff: clean. cs: memory probe 0xa0000000-0xa0ffffff: clean. cs: memory probe 0xdea00000-0xdeafffff: excluding 0xdea00000-0xdeafffff cs: memory probe 0xff600000-0xff6fffff: excluding 0xff600000-0xff60ffff 0xff6a0000-0xff6dffff 0xff6f0000-0xff6fffff pcmcia: registering new device pcmcia0.0 # insmod pata_pcmcia.ko scsi2 : pata_pcmcia ata3: PATA max PIO0 cmd 0x0001d100 ctl 0x0001d10e bmdma 0x00000000 irq 9 ata3.00: CFA: , verB2.10, max PIO2 ata3.00: 507904 sectors, multi 0: LBA ata3.00: configured for PIO0 scsi 2:0:0:0: Direct-Access ATA verB PQ: 0 ANSI: 5 sd 2:0:0:0: [sdb] 507904 512-byte hardware sectors (260 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdb] 507904 512-byte hardware sectors (260 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sd 2:0:0:0: [sdb] Attached SCSI removable disk sd 2:0:0:0: Attached scsi generic sg2 type 0 System is a Vaio with ICH4 and TI PCI7420 Cardbus bridge. If you need more info, please don't hesitate to ask. Thank you, Manuel Lauss - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
