Tejun Heo writes: > Igor Durdanovic wrote: > > Tejun Heo writes: > >> PMP patchset is not in mainline yet. You need to apply patches from the > >> following page. > >> > >> http://home-tj.org/wiki/index.php/Libata-tj-stable > > > > Yes! it works now (though there were tons of hard and soft resets > > during booting, if you need log I can email it). > > Yeah, please post the log. Also, please cc linux-ide@xxxxxxxxxxxxxxxx No problem, here is the log of sata_sil24 while booting the kernel 2.6.22.1 on Dell latitude D820 with SIIG SC-SAE512-S1 SATA II ExpressCard 54 connected to DS-2350S 5-BAY enclosure. Regards, Igor sata_sil24 0000:0d:00.0: version 1.0 ACPI: PCI Interrupt 0000:0d:00.0[A] -> GSI 19 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:0d:00.0 to 64 scsi2 : sata_sil24 scsi3 : sata_sil24 ata3: SATA max UDMA/100 cmd 0xf8d08000 ctl 0x00000000 bmdma 0x00000000 irq 16 ata4: SATA max UDMA/100 cmd 0xf8d0a000 ctl 0x00000000 bmdma 0x00000000 irq 16 ata3: SATA link down (SStatus 0 SControl 0) ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 0) ata4.15: Port Multiplier 1.1, 0x1095:0x4726 r31, 7 ports, feat 0x1/0x9 ata4.00: hard resetting link ata4.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.01: hard resetting link ata4.01: softreset failed (SRST command error) ata4.01: reset failed (errno=-5), retrying in 10 secs ata4.01: hard resetting link ata4.02: hard resetting link ata4.02: COMRESET failed (errno=-5) ata4.02: reset failed, giving up ata4.15: hard resetting link ata4: controller in dubious state, performing PORT_RST ata4.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) ata4.00: hard resetting link ata4.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.01: hard resetting link ata4.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.02: hard resetting link ata4.02: softreset failed (SRST command error) ata4.02: reset failed (errno=-5), retrying in 10 secs ata4.02: hard resetting link ata4.03: hard resetting link ata4.03: COMRESET failed (errno=-5) ata4.03: reset failed, giving up ata4.15: hard resetting link ata4: controller in dubious state, performing PORT_RST ata4.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) ata4.00: hard resetting link ata4.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.01: hard resetting link ata4.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.02: hard resetting link ata4.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.03: hard resetting link ata4.03: softreset failed (SRST command error) ata4.03: reset failed (errno=-5), retrying in 10 secs ata4.03: hard resetting link ata4.04: hard resetting link ata4.04: COMRESET failed (errno=-5) ata4.04: reset failed, giving up ata4.15: hard resetting link ata4: controller in dubious state, performing PORT_RST ata4.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) ata4.00: hard resetting link ata4.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.01: hard resetting link ata4.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.02: hard resetting link ata4.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.03: hard resetting link ata4.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.04: hard resetting link ata4.04: softreset failed (SRST command error) ata4.04: reset failed (errno=-5), retrying in 10 secs ata4.04: hard resetting link ata4.05: hard resetting link ata4.05: COMRESET failed (errno=-5) ata4.05: reset failed, giving up ata4.15: hard resetting link ata4: controller in dubious state, performing PORT_RST ata4.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) ata4.00: hard resetting link ata4.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.01: hard resetting link ata4.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.02: hard resetting link ata4.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.03: hard resetting link ata4.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.04: hard resetting link ata4.04: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.05: hard resetting link ata4.05: SATA link up 3.0 Gbps (SStatus 123 SControl 0) ata4.06: hard resetting link ata4.06: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.00: ATA-7: ST3750640AS, 3.AAE, max UDMA/133 ata4.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata4.00: configured for UDMA/100 ata4.01: ATA-7: ST3750640AS, 3.AAD, max UDMA/133 ata4.01: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata4.01: configured for UDMA/100 ata4.02: ATA-7: ST3750640AS, 3.AAE, max UDMA/133 ata4.02: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata4.02: configured for UDMA/100 ata4.03: ATA-7: ST3750640AS, 3.AAD, max UDMA/133 ata4.03: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata4.03: configured for UDMA/100 ata4.04: ATA-7: ST3750640AS, 3.AAE, max UDMA/133 ata4.04: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata4.04: configured for UDMA/100 ata4.05: ATA-6: Config Disk, PLS12052, max UDMA/133 ata4.05: 640 sectors, multi 1: LBA ata4.05: device is on DMA blacklist, disabling DMA ata4.05: configured for PIO4 ata4: EH complete scsi 3:0:0:0: Direct-Access ATA ST3750640AS 3.AA PQ: 0 ANSI: 5 sd 3:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB) sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB) sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sdb: unknown partition table sd 3:0:0:0: [sdb] Attached SCSI disk sd 3:0:0:0: Attached scsi generic sg2 type 0 scsi 3:1:0:0: Direct-Access ATA ST3750640AS 3.AA PQ: 0 ANSI: 5 sd 3:1:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB) sd 3:1:0:0: [sdc] Write Protect is off sd 3:1:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:1:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB) sd 3:1:0:0: [sdc] Write Protect is off sd 3:1:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc1 sd 3:1:0:0: [sdc] Attached SCSI disk sd 3:1:0:0: Attached scsi generic sg3 type 0 scsi 3:2:0:0: Direct-Access ATA ST3750640AS 3.AA PQ: 0 ANSI: 5 sd 3:2:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB) sd 3:2:0:0: [sdd] Write Protect is off sd 3:2:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 3:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:2:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB) sd 3:2:0:0: [sdd] Write Protect is off sd 3:2:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 3:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdd: sdd1 sd 3:2:0:0: [sdd] Attached SCSI disk sd 3:2:0:0: Attached scsi generic sg4 type 0 scsi 3:3:0:0: Direct-Access ATA ST3750640AS 3.AA PQ: 0 ANSI: 5 sd 3:3:0:0: [sde] 1465149168 512-byte hardware sectors (750156 MB) sd 3:3:0:0: [sde] Write Protect is off sd 3:3:0:0: [sde] Mode Sense: 00 3a 00 00 sd 3:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:3:0:0: [sde] 1465149168 512-byte hardware sectors (750156 MB) sd 3:3:0:0: [sde] Write Protect is off sd 3:3:0:0: [sde] Mode Sense: 00 3a 00 00 sd 3:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: sde1 sd 3:3:0:0: [sde] Attached SCSI disk sd 3:3:0:0: Attached scsi generic sg5 type 0 scsi 3:4:0:0: Direct-Access ATA ST3750640AS 3.AA PQ: 0 ANSI: 5 sd 3:4:0:0: [sdf] 1465149168 512-byte hardware sectors (750156 MB) sd 3:4:0:0: [sdf] Write Protect is off sd 3:4:0:0: [sdf] Mode Sense: 00 3a 00 00 sd 3:4:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:4:0:0: [sdf] 1465149168 512-byte hardware sectors (750156 MB) sd 3:4:0:0: [sdf] Write Protect is off sd 3:4:0:0: [sdf] Mode Sense: 00 3a 00 00 sd 3:4:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdf: sdf1 sdf2 sdf3 sdf4 < sdf5 sdf6 sdf7 sdf8 sdf9 sdf10 sdf11 > sd 3:4:0:0: [sdf] Attached SCSI disk sd 3:4:0:0: Attached scsi generic sg6 type 0 scsi 3:5:0:0: Direct-Access ATA Config Disk PLS1 PQ: 0 ANSI: 5 sd 3:5:0:0: [sdg] 640 512-byte hardware sectors (0 MB) sd 3:5:0:0: [sdg] Write Protect is off sd 3:5:0:0: [sdg] Mode Sense: 00 3a 00 00 sd 3:5:0:0: [sdg] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 3:5:0:0: [sdg] 640 512-byte hardware sectors (0 MB) sd 3:5:0:0: [sdg] Write Protect is off sd 3:5:0:0: [sdg] Mode Sense: 00 3a 00 00 sd 3:5:0:0: [sdg] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sdg: unknown partition table sd 3:5:0:0: [sdg] Attached SCSI disk sd 3:5:0:0: Attached scsi generic sg7 type 0 video1394: Installed video1394 module ieee1394: raw1394: /dev/raw1394 device initialized eth1394: eth1: IPv4 over IEEE 1394 (fw-host0) Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input3 input: PC Speaker as /class/input/input4 i2c /dev entries driver i2c-core: driver [dev_driver] registered ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 18 i801_smbus 0000:00:1f.3: SMBus using interrupt SMI# i2c-adapter i2c-0: adapter [SMBus I801 adapter at 10c0] registered i2c-dev: adapter [SMBus I801 adapter at 10c0] registered as minor 0 raid6: int32x1 750 MB/s raid6: int32x2 800 MB/s raid6: int32x4 593 MB/s raid6: int32x8 632 MB/s raid6: mmxx1 2296 MB/s raid6: mmxx2 2871 MB/s raid6: sse1x1 1546 MB/s raid6: sse1x2 2125 MB/s raid6: sse2x1 2941 MB/s raid6: sse2x2 3375 MB/s raid6: using algorithm sse2x2 (3375 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: automatically using best checksumming function: pIII_sse pIII_sse : 7112.000 MB/sec raid5: using function: pIII_sse (7112.000 MB/sec) device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html