Just testet 2.6.22 on my setup. Unfortunately the problem is still there.
Interesting part of dmesg:
[ 33.036786] sata_promise 0000:01:08.0: applying SATAII TX4 port
numbering workaround
[ 33.036926] scsi0 : sata_promise
[ 33.037032] scsi1 : sata_promise
[ 33.037125] scsi2 : sata_promise
[ 33.037221] scsi3 : sata_promise
[ 33.037303] ata1: SATA max UDMA/133 cmd 0xe0814380 ctl 0xe08143b8
bmdma 0x00000000 irq 11
[ 33.037363] ata2: SATA max UDMA/133 cmd 0xe0814280 ctl 0xe08142b8
bmdma 0x00000000 irq 11
[ 33.037422] ata3: SATA max UDMA/133 cmd 0xe0814200 ctl 0xe0814238
bmdma 0x00000000 irq 11
[ 33.037481] ata4: SATA max UDMA/133 cmd 0xe0814300 ctl 0xe0814338
bmdma 0x00000000 irq 11
[ 33.504834] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 33.561725] ata1.00: ATA-7: ST3500630NS, 3.AEE, max UDMA/133
[ 33.561774] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 33.653311] ata1.00: configured for UDMA/133
[ 34.120556] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 34.176731] ata2.00: ATA-7: ST3500630NS, 3.AEE, max UDMA/133
[ 34.176779] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 34.268312] ata2.00: configured for UDMA/133
[ 34.732282] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 34.787158] ata3.00: ATA-7: ST3500630NS, 3.AEE, max UDMA/133
[ 34.787206] ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 34.870410] ata3.00: configured for UDMA/133
[ 35.336011] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 35.389438] ata4.00: ATA-7: ST3500630NS, 3.AEE, max UDMA/133
[ 35.389486] ata4.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 35.472698] ata4.00: configured for UDMA/133
[ 35.472822] scsi 0:0:0:0: Direct-Access ATA ST3500630NS
3.AE PQ: 0 ANSI: 5
[ 35.472966] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors
(500108 MB)
[ 35.473028] sd 0:0:0:0: [sda] Write Protect is off
[ 35.473089] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 35.473192] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors
(500108 MB)
[ 35.473248] sd 0:0:0:0: [sda] Write Protect is off
[ 35.473308] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 35.473368] sda: unknown partition table
[ 35.491503] sd 0:0:0:0: [sda] Attached SCSI disk
[ 35.491604] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3993.963562] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x1380000
action 0x2 frozen
[ 3993.963576] ata1.00: cmd c8/00:00:00:15:4c/00:00:00:00:00/ec tag 0
cdb 0x0 data 131072 in
[ 3993.963579] res 40/00:01:09:4f:c2/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 3999.312950] ata1: port is slow to respond, please be patient (Status
0xff)
[ 4004.014836] ata1: device not ready (errno=-16), forcing hardreset
[ 4004.014845] ata1: hard resetting port
[ 4009.528375] ata1: port is slow to respond, please be patient (Status
0xff)
[ 4014.062329] ata1: COMRESET failed (errno=-16)
[ 4014.062338] ata1: hard resetting port
[ 4019.575900] ata1: port is slow to respond, please be patient (Status
0xff)
[ 4024.109824] ata1: COMRESET failed (errno=-16)
[ 4024.109833] ata1: hard resetting port
[ 4029.623411] ata1: port is slow to respond, please be patient (Status
0xff)
[ 4059.122095] ata1: COMRESET failed (errno=-16)
[ 4059.122108] ata1: limiting SATA link speed to 1.5 Gbps
[ 4059.122111] ata1: hard resetting port
[ 4064.131863] ata1: COMRESET failed (errno=-16)
[ 4064.131872] ata1: reset failed, giving up
[ 4064.131875] ata1.00: disabled
[ 4064.131891] ata1: EH complete
[ 4064.132621] sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
[ 4064.132628] end_request: I/O error, dev sda, sector 206312704
[ 4064.132632] Buffer I/O error on device sda, logical block 25789088
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
