Possibly a known issue: After resume pata_amd drops from UDMA/33 to PIO on my system. Reloading the module puts both attached optical drives (master and slave) back to UDMA/33. AFAICS "simplex DMA is claimed by other device, disabling DMA" seems to be causing it to drop to PIO (but only after a suspend/resume cycle, not on boot or module load). Burning a DVD with 6x speed using PIO makes heavy use of burnproof and makes the whole system quite sluggish. :) [ 0.000000] Linux version 2.6.20-amd64 (ranma@melchior) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #63 Sun Feb 11 10:58:36 CET 2007 [ 0.000000] Command line: root=/dev/sda5 resume=/dev/sda6 vga=6 apic=verbose netconsole=@xxxxxxxxxxxxx/,514@xxxxxxxxxxxxxxx/ ro [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003fee0000 (usable) [ 0.000000] BIOS-e820: 000000003fee0000 - 000000003fee3000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003fee3000 - 000000003fef0000 (ACPI data) [ 0.000000] BIOS-e820: 000000003fef0000 - 000000003ff00000 (reserved) [ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 261856) 1 entries of 256 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI 2.4 present. [ 0.000000] ACPI: RSDP (v002 Nvidia ) @ 0x00000000000f7b70 [ 0.000000] ACPI: XSDT (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fee30c0 [ 0.000000] ACPI: FADT (v003 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003feec5c0 [ 0.000000] ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x000000003feec7c0 [ 0.000000] ACPI: HPET (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000098) @ 0x000000003feec900 [ 0.000000] ACPI: MCFG (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003feec980 [ 0.000000] ACPI: MADT (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003feec700 [ 0.000000] ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x03000000) @ 0x0000000000000000 [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 261856) 1 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 261856 [ 0.000000] On node 0 totalpages: 261759 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 1338 pages reserved [ 0.000000] DMA zone: 2605 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 3524 pages used for memmap [ 0.000000] DMA32 zone: 254236 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ14 used by override. [ 0.000000] ACPI: IRQ15 used by override. [ 0.000000] Setting APIC routing to flat [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfefff000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] mapped APIC to ffffffffff5fd000 ( fee00000) [ 0.000000] mapped IOAPIC to ffffffffff5fc000 (00000000fec00000) [ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000 [ 0.000000] Nosave address range: 00000000000a0000 - 00000000000f0000 [ 0.000000] Nosave address range: 00000000000f0000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3ff00000:b0100000) [ 0.000000] Built 1 zonelists. Total pages: 256841 [ 0.000000] Kernel command line: root=/dev/sda5 resume=/dev/sda6 vga=6 apic=verbose netconsole=@xxxxxxxxxxxxx/,514@xxxxxxxxxxxxxxx/ ro [ 0.000000] netconsole: local port 6665 [ 0.000000] netconsole: local IP 192.168.8.241 [ 0.000000] netconsole: interface eth0 [ 0.000000] netconsole: remote port 514 [ 0.000000] netconsole: remote IP 255.255.255.255 [ 0.000000] netconsole: remote ethernet address ff:ff:ff:ff:ff:ff [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 24.288641] time.c: Using 25.000000 MHz WALL HPET GTOD HPET/TSC timer. [ 24.288644] time.c: Detected 2009.259 MHz processor. [ 24.294154] Console: colour VGA+ 80x60 [ 24.296776] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 24.297614] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 24.297857] Checking aperture... [ 24.297966] CPU 0: aperture @ b0ca000000 size 32 MB [ 24.298073] Aperture too small (32 MB) [ 24.302864] No AGP bridge found [ 24.310527] Memory: 1025428k/1047424k available (3185k kernel code, 21364k reserved, 1446k data, 200k init) [ 24.392078] Calibrating delay using timer specific routine.. 4023.48 BogoMIPS (lpj=6703172) [ 24.392325] Mount-cache hash table entries: 256 [ 24.392502] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 24.392611] CPU: L2 Cache: 512K (64 bytes/line) [ 24.392736] CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 02 [ 24.392889] ACPI: Core revision 20060707 [ 24.395352] ACPI (tbget-0289): Table [DSDT] replaced by host OS [20060707] [ 24.401100] enabled ExtINT on CPU#0 [ 24.401207] ESR value after enabling vector: 00000000, after 00000004 [ 24.401543] ENABLING IO-APIC IRQs [ 24.401650] init IO_APIC IRQs [ 24.401652] IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. [ 24.401848] ..TIMER: vector=0x20 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 24.434946] Using local APIC timer interrupts. [ 24.484761] result 12557887 [ 24.484867] Detected 12.557 MHz APIC timer. [ 24.485290] testing NMI watchdog ... OK. [ 24.518570] NET: Registered protocol family 16 [ 24.518739] ACPI: bus type pci registered [ 24.521493] PCI: Using MMCONFIG at f0000000 [ 24.521620] PCI: No mmconfig possible on device 00:18 [ 24.531607] ACPI: Interpreter enabled [ 24.531717] ACPI: Using IOAPIC for interrupt routing [ 24.532449] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 24.532560] PCI: Probing PCI hardware (bus 00) [ 24.535027] PCI: Transparent bridge - 0000:00:06.0 [ 24.535485] Boot video device is 0000:07:00.0 [ 24.535558] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 24.657903] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] [ 24.660295] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 *10 11 14 15) [ 24.661027] ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15) [ 24.661766] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 *11 14 15) [ 24.662493] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 24.663346] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 24.664201] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 *7 9 10 11 14 15) [ 24.664933] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15) [ 24.665667] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 24.666520] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 24.667374] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15) [ 24.668106] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15) [ 24.668855] ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 *10 11 14 15) [ 24.669586] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15) [ 24.670332] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 24.671185] ACPI: PCI Interrupt Link [LSMB] (IRQs *5 7 9 10 11 14 15) [ 24.671943] ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15) [ 24.672676] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 24.673528] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 24.674381] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 24.675242] ACPI: PCI Interrupt Link [LSA2] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 24.676176] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. [ 24.676897] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. [ 24.677619] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. [ 24.678339] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. [ 24.679066] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled. [ 24.679786] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled. [ 24.680510] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled. [ 24.681231] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled. [ 24.681962] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled. [ 24.682745] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled. [ 24.683528] ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0, disabled. [ 24.684310] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled. [ 24.685098] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled. [ 24.685883] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled. [ 24.686666] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled. [ 24.687448] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled. [ 24.688231] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. [ 24.689023] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled. [ 24.689805] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled. [ 24.690588] ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0, disabled. [ 24.693822] Linux Plug and Play Support v0.97 (c) Adam Belay [ 24.693936] pnp: PnP ACPI init [ 24.699645] IOAPIC[0]: Set PCI routing entry (2-8 -> 0x28 -> IRQ 8 Mode:0 Active:0) [ 24.699820] IOAPIC[0]: Set PCI routing entry (2-13 -> 0x2d -> IRQ 13 Mode:0 Active:0) [ 24.700821] IOAPIC[0]: Set PCI routing entry (2-4 -> 0x24 -> IRQ 4 Mode:0 Active:0) [ 24.702557] pnp: PnP ACPI: found 11 devices [ 24.702755] SCSI subsystem initialized [ 24.702881] libata version 2.00 loaded. [ 24.702918] usbcore: registered new interface driver usbfs [ 24.703046] usbcore: registered new interface driver hub [ 24.703176] usbcore: registered new device driver usb [ 24.703323] PCI: Using ACPI for IRQ routing [ 24.703433] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 24.703627] number of MP IRQ sources: 15. [ 24.703629] number of IO-APIC #2 registers: 24. [ 24.703631] testing the IO APIC....................... [ 24.703743] [ 24.703848] IO APIC #2...... [ 24.703850] .... register #00: 02000000 [ 24.703852] ....... : physical APIC id: 02 [ 24.703854] .... register #01: 00170011 [ 24.703856] ....... : max redirection entries: 0017 [ 24.703857] ....... : PRQ implemented: 0 [ 24.703859] ....... : IO APIC version: 0011 [ 24.703861] .... register #02: 02000000 [ 24.703863] ....... : arbitration: 02 [ 24.703864] .... IRQ redirection table: [ 24.703866] NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: [ 24.703871] 00 000 00 1 0 0 0 0 0 0 00 [ 24.703878] 01 001 01 0 0 0 0 0 1 1 21 [ 24.703884] 02 001 01 0 0 0 0 0 1 1 20 [ 24.703891] 03 001 01 0 0 0 0 0 1 1 23 [ 24.703897] 04 001 01 1 0 0 0 0 1 1 24 [ 24.703903] 05 001 01 1 0 0 0 0 1 1 25 [ 24.703910] 06 001 01 0 0 0 0 0 1 1 26 [ 24.703916] 07 001 01 1 0 0 0 0 1 1 27 [ 24.703922] 08 001 01 1 0 0 0 0 1 1 28 [ 24.703929] 09 001 01 0 1 0 0 0 1 1 29 [ 24.703935] 0a 001 01 1 0 0 0 0 1 1 2A [ 24.703942] 0b 001 01 1 0 0 0 0 1 1 2B [ 24.703948] 0c 001 01 0 0 0 0 0 1 1 2C [ 24.703954] 0d 001 01 1 0 0 0 0 1 1 2D [ 24.703961] 0e 001 01 0 0 0 0 0 1 1 2E [ 24.703967] 0f 001 01 0 0 0 0 0 1 1 2F [ 24.703973] 10 000 00 1 0 0 0 0 0 0 00 [ 24.703980] 11 000 00 1 0 0 0 0 0 0 00 [ 24.703986] 12 000 00 1 0 0 0 0 0 0 00 [ 24.703992] 13 000 00 1 0 0 0 0 0 0 00 [ 24.703998] 14 000 00 1 0 0 0 0 0 0 00 [ 24.704004] 15 000 00 1 0 0 0 0 0 0 00 [ 24.704011] 16 000 00 1 0 0 0 0 0 0 00 [ 24.704017] 17 000 00 1 0 0 0 0 0 0 00 [ 24.704020] IRQ to pin mappings: [ 24.704021] IRQ0 -> 0:2 [ 24.704023] IRQ1 -> 0:1 [ 24.704025] IRQ3 -> 0:3 [ 24.704026] IRQ4 -> 0:4 [ 24.704028] IRQ5 -> 0:5 [ 24.704030] IRQ6 -> 0:6 [ 24.704031] IRQ7 -> 0:7 [ 24.704033] IRQ8 -> 0:8 [ 24.704035] IRQ9 -> 0:9 [ 24.704036] IRQ10 -> 0:10 [ 24.704038] IRQ11 -> 0:11 [ 24.704040] IRQ12 -> 0:12 [ 24.704042] IRQ13 -> 0:13 [ 24.704044] IRQ14 -> 0:14 [ 24.704045] IRQ15 -> 0:15 [ 24.704048] .................................... done. [ 24.801570] hpet0: at MMIO 0xfefff000, IRQs 2, 8, 31 [ 24.801758] hpet0: 3 32-bit timers, 25000000 Hz [ 24.803395] pnp: 00:01: ioport range 0x1000-0x107f could not be reserved [ 24.803504] pnp: 00:01: ioport range 0x1080-0x10ff has been reserved [ 24.803613] pnp: 00:01: ioport range 0x1400-0x147f has been reserved [ 24.803721] pnp: 00:01: ioport range 0x1480-0x14ff could not be reserved [ 24.803830] pnp: 00:01: ioport range 0x1800-0x187f has been reserved [ 24.803938] pnp: 00:01: ioport range 0x1880-0x18ff has been reserved [ 24.804236] PCI: Bridge: 0000:00:06.0 [ 24.804343] IO window: d000-dfff [ 24.804451] MEM window: fde00000-fdefffff [ 24.804559] PREFETCH window: 40000000-400fffff [ 24.804666] PCI: Bridge: 0000:00:0a.0 [ 24.804773] IO window: disabled. [ 24.804879] MEM window: disabled. [ 24.804992] PREFETCH window: disabled. [ 24.805099] PCI: Bridge: 0000:00:0b.0 [ 24.805205] IO window: disabled. [ 24.805312] MEM window: disabled. [ 24.805418] PREFETCH window: disabled. [ 24.805525] PCI: Bridge: 0000:00:0c.0 [ 24.805631] IO window: disabled. [ 24.805738] MEM window: disabled. [ 24.805845] PREFETCH window: disabled. [ 24.805951] PCI: Bridge: 0000:00:0d.0 [ 24.806058] IO window: disabled. [ 24.806165] MEM window: disabled. [ 24.806271] PREFETCH window: disabled. [ 24.806379] PCI: Bridge: 0000:00:0e.0 [ 24.806486] IO window: b000-cfff [ 24.806593] MEM window: fdd00000-fddfffff [ 24.806700] PREFETCH window: disabled. [ 24.806807] PCI: Bridge: 0000:00:0f.0 [ 24.806914] IO window: a000-afff [ 24.807022] MEM window: fdc00000-fdcfffff [ 24.807129] PREFETCH window: e8000000-efffffff [ 24.807241] PCI: Setting latency timer of device 0000:00:06.0 to 64 [ 24.807247] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 24.807251] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 24.807256] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 24.807261] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 24.807265] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 24.807270] PCI: Setting latency timer of device 0000:00:0f.0 to 64 [ 24.807288] NET: Registered protocol family 2 [ 24.834882] IP route cache hash table entries: 32768 (order: 6, 262144 bytes) [ 24.835191] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 24.835856] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 24.842108] TCP: Hash tables configured (established 131072 bind 65536) [ 24.842216] TCP reno registered [ 24.852114] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx). [ 24.852354] JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. [ 24.852497] fuse init (API version 7.8) [ 24.852673] io scheduler noop registered [ 24.852800] io scheduler anticipatory registered [ 24.852927] io scheduler deadline registered [ 24.853061] io scheduler cfq registered (default) [ 24.865671] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 24.865684] assign_interrupt_mode Found MSI capability [ 24.865807] Allocate Port Service[0000:00:0a.0:pcie00] [ 24.865835] Allocate Port Service[0000:00:0a.0:pcie03] [ 24.865873] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 24.865886] assign_interrupt_mode Found MSI capability [ 24.866002] Allocate Port Service[0000:00:0b.0:pcie00] [ 24.866023] Allocate Port Service[0000:00:0b.0:pcie03] [ 24.866061] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 24.866073] assign_interrupt_mode Found MSI capability [ 24.866189] Allocate Port Service[0000:00:0c.0:pcie00] [ 24.866210] Allocate Port Service[0000:00:0c.0:pcie03] [ 24.866246] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 24.866259] assign_interrupt_mode Found MSI capability [ 24.866374] Allocate Port Service[0000:00:0d.0:pcie00] [ 24.866396] Allocate Port Service[0000:00:0d.0:pcie03] [ 24.866436] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 24.866448] assign_interrupt_mode Found MSI capability [ 24.866563] Allocate Port Service[0000:00:0e.0:pcie00] [ 24.866585] Allocate Port Service[0000:00:0e.0:pcie03] [ 24.866622] PCI: Setting latency timer of device 0000:00:0f.0 to 64 [ 24.866634] assign_interrupt_mode Found MSI capability [ 24.866749] Allocate Port Service[0000:00:0f.0:pcie00] [ 24.866773] Allocate Port Service[0000:00:0f.0:pcie03] [ 24.866945] input: Power Button (FF) as /class/input/input0 [ 24.867053] ACPI: Power Button (FF) [PWRF] [ 24.867211] input: Power Button (CM) as /class/input/input1 [ 24.867319] ACPI: Power Button (CM) [PWRB] [ 24.867449] ACPI: Fan [FAN] (on) [ 24.867603] ACPI: Processor [CPU0] (supports 8 throttling states) [ 24.868761] ACPI: Thermal Zone [THRM] (23 C) [ 24.870244] Real Time Clock Driver v1.12ac [ 24.870509] hpet_resources: 0xfefff000 is busy [ 24.870515] Linux agpgart interface v0.101 (c) Dave Jones [ 24.870799] loop: loaded (max 8 devices) [ 24.870979] tun: Universal TUN/TAP device driver, 1.6 [ 24.871086] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx> [ 24.871217] netconsole: eth0 doesn't exist, aborting. [ 24.871406] ahci 0000:06:00.0: version 2.0 [ 24.871965] ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16 [ 24.872076] IOAPIC[0]: Set PCI routing entry (2-16 -> 0x69 -> IRQ 16 Mode:1 Active:1) [ 24.872082] ACPI: PCI Interrupt 0000:06:00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16 [ 25.873557] PCI: Setting latency timer of device 0000:06:00.0 to 64 [ 25.873564] ahci 0000:06:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode [ 25.873759] ahci 0000:06:00.0: flags: 64bit ncq pm led clo pmp pio slum part [ 25.873973] ata1: SATA max UDMA/133 cmd 0xFFFFC20000060100 ctl 0x0 bmdma 0x0 irq 16 [ 25.874252] ata2: SATA max UDMA/133 cmd 0xFFFFC20000060180 ctl 0x0 bmdma 0x0 irq 16 [ 25.874453] scsi0 : ahci [ 26.186481] ata1: SATA link down (SStatus 0 SControl 300) [ 26.186595] scsi1 : ahci [ 26.665886] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 26.668868] ata2.00: ATA-7, max UDMA7, 488397168 sectors: LBA48 NCQ (depth 31/32) [ 26.696451] ata2.00: configured for UDMA/133 [ 26.696620] scsi 1:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5 [ 26.696875] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) [ 26.696989] sda: Write Protect is off [ 26.697096] sda: Mode Sense: 00 3a 00 00 [ 26.697106] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 26.697329] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) [ 26.697440] sda: Write Protect is off [ 26.697548] sda: Mode Sense: 00 3a 00 00 [ 26.697557] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 26.697750] sda: sda1 sda2 sda4 < sda5 sda6 > [ 26.733930] sd 1:0:0:0: Attached scsi disk sda [ 26.734080] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 26.734259] block2mtd: version $Revision: 1.30 $ [ 26.734949] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23 [ 26.735059] IOAPIC[0]: Set PCI routing entry (2-23 -> 0x71 -> IRQ 23 Mode:1 Active:1) [ 26.735066] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 23 [ 26.735308] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 26.735310] ehci_hcd 0000:00:02.1: EHCI Host Controller [ 26.735452] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 [ 26.735669] ehci_hcd 0000:00:02.1: debug port 1 [ 26.735785] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 26.735793] ehci_hcd 0000:00:02.1: irq 23, io mem 0xfe02e000 [ 26.735905] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 26.736180] usb usb1: configuration #1 chosen from 1 choice [ 26.736315] hub 1-0:1.0: USB hub found [ 26.736428] hub 1-0:1.0: 10 ports detected [ 26.839042] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) [ 26.839571] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22 [ 26.839681] IOAPIC[0]: Set PCI routing entry (2-22 -> 0x79 -> IRQ 22 Mode:1 Active:1) [ 26.839686] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 22 [ 26.839924] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 26.839926] ohci_hcd 0000:00:02.0: OHCI Host Controller [ 26.840062] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 [ 26.840264] ohci_hcd 0000:00:02.0: irq 22, io mem 0xfe02f000 [ 26.894316] usb usb2: configuration #1 chosen from 1 choice [ 26.894448] hub 2-0:1.0: USB hub found [ 26.894561] hub 2-0:1.0: 10 ports detected [ 26.995510] USB Universal Host Controller Interface driver v3.0 [ 27.065367] usb 1-2: new high speed USB device using ehci_hcd and address 2 [ 27.189770] usb 1-2: configuration #1 chosen from 1 choice [ 27.190113] hub 1-2:1.0: USB hub found [ 27.190465] hub 1-2:1.0: 4 ports detected [ 27.881000] usb 2-3: new full speed USB device using ohci_hcd and address 2 [ 28.030879] usb 2-3: configuration #1 chosen from 1 choice [ 28.270507] usb 2-5: new full speed USB device using ohci_hcd and address 3 [ 28.423381] usb 2-5: configuration #1 chosen from 1 choice [ 28.613671] usb 1-2.3: new low speed USB device using ehci_hcd and address 5 [ 28.702232] usb 1-2.3: configuration #1 chosen from 1 choice [ 28.889946] usb 1-2.4: new low speed USB device using ehci_hcd and address 6 [ 28.976762] usb 1-2.4: configuration #1 chosen from 1 choice [ 28.977405] usbcore: registered new interface driver usblp [ 28.977513] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 28.980420] input: Logitech USB-PS/2 Optical Mouse as /class/input/input2 [ 28.980530] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.1-2.3 [ 28.984787] input: HID 046a:0001 as /class/input/input3 [ 28.984902] input: USB HID v1.00 Keyboard [HID 046a:0001] on usb-0000:00:02.1-2.4 [ 28.985136] usbcore: registered new interface driver usbhid [ 28.985244] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 28.985422] PNP: No PS/2 controller found. Probing ports directly. [ 28.985727] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 28.985837] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 28.986046] mice: PS/2 mouse device common for all mice [ 29.100577] i2c /dev entries driver [ 29.100808] i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00 [ 29.100952] i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c40 [ 29.101104] it87: Found IT8716F chip at 0x290, revision 0 [ 29.101219] it87: in3 is VCC (+5V) [ 29.101325] it87: in7 is VCCH (+5V Stand-By) [ 29.101642] md: raid1 personality registered for level 1 [ 29.101795] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx [ 29.102049] GACT probability on [ 29.102156] Mirror/redirect action on [ 29.102308] u32 classifier [ 29.102414] Performance counters on [ 29.102521] input device check on [ 29.102627] Actions configured [ 29.102740] IPv4 over IPv4 tunneling driver [ 29.102922] ip_tables: (C) 2000-2006 Netfilter Core Team [ 29.205996] TCP bic registered [ 29.206103] TCP cubic registered [ 29.206210] TCP westwood registered [ 29.206316] TCP htcp registered [ 29.206423] TCP vegas registered [ 29.206530] Initializing XFRM netlink socket [ 29.206642] NET: Registered protocol family 1 [ 29.206772] NET: Registered protocol family 10 [ 29.206982] IPv6 over IPv4 tunneling driver [ 29.207155] NET: Registered protocol family 17 [ 29.207263] NET: Registered protocol family 15 [ 29.285888] Bridge firewalling registered [ 29.286025] 802.1Q VLAN Support v1.8 Ben Greear <greearb@xxxxxxxxxxxxxxx> [ 29.286133] All bugs added by David S. Miller <davem@xxxxxxxxxx> [ 29.286264] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3200+ processors (version 2.00.00) [ 29.286484] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 [ 29.286592] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa [ 29.286700] powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12 [ 29.292979] ACPI: (supports S0 S1 S3 S4 S5) [ 29.293291] md: Autodetecting RAID arrays. [ 29.293398] md: autorun ... [ 29.293505] md: ... autorun DONE. [ 29.304470] EXT3-fs: INFO: recovery required on readonly filesystem. [ 29.304578] EXT3-fs: write access will be enabled during recovery. [ 30.121789] kjournald starting. Commit interval 5 seconds [ 30.121905] EXT3-fs: recovery complete. [ 30.122246] EXT3-fs: mounted filesystem with ordered data mode. [ 30.122396] VFS: Mounted root (ext3 filesystem) readonly. [ 30.122539] Freeing unused kernel memory: 200k freed [ 31.907348] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59. [ 31.908131] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21 [ 31.908242] IOAPIC[0]: Set PCI routing entry (2-21 -> 0x81 -> IRQ 21 Mode:1 Active:1) [ 31.908249] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 21 [ 31.908484] PCI: Setting latency timer of device 0000:00:08.0 to 64 [ 31.908491] forcedeth: using HIGHDMA [ 31.992612] usbcore: registered new interface driver usbserial [ 31.992731] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic [ 31.992938] usbcore: registered new interface driver usbserial_generic [ 31.993046] drivers/usb/serial/usb-serial.c: USB Serial Driver core [ 32.063166] drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 [ 32.063378] pl2303 2-5:1.0: pl2303 converter detected [ 32.063530] usb 2-5: pl2303 converter now attached to ttyUSB0 [ 32.063641] usbcore: registered new interface driver pl2303 [ 32.063749] drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver [ 32.422156] eth0: forcedeth.c: subsystem: 01043:8239 bound to 0000:00:08.0 [ 32.422836] ACPI: PCI Interrupt Link [AMC1] enabled at IRQ 20 [ 32.422947] IOAPIC[0]: Set PCI routing entry (2-20 -> 0x89 -> IRQ 20 Mode:1 Active:1) [ 32.422953] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [AMC1] -> GSI 20 (level, low) -> IRQ 20 [ 32.423189] PCI: Setting latency timer of device 0000:00:09.0 to 64 [ 32.423196] forcedeth: using HIGHDMA [ 32.938172] eth1: forcedeth.c: subsystem: 01043:8239 bound to 0000:00:09.0 [ 32.938468] pata_amd 0000:00:04.0: version 0.2.7 [ 32.938486] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 32.938936] ata3: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14 [ 32.939073] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15 [ 32.939198] scsi2 : pata_amd [ 33.251005] ata3.00: ATAPI, max UDMA/33 [ 33.410820] ata3.01: ATAPI, max UDMA/66 [ 33.570598] ata3.00: configured for UDMA/33 [ 33.730440] ata3.01: configured for UDMA/66 [ 33.730556] scsi3 : pata_amd [ 33.730713] ata4: port disabled. ignoring. [ 33.730716] ata4: reset failed, giving up [ 33.731743] scsi 2:0:0:0: CD-ROM _NEC DVD_RW ND-3500AG 2.1A PQ: 0 ANSI: 5 [ 33.734667] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray [ 33.734776] Uniform CD-ROM driver Revision: 3.20 [ 33.734910] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 33.734936] sr 2:0:0:0: Attached scsi generic sg1 type 5 [ 33.736169] scsi 2:0:1:0: CD-ROM PIONEER DVD-ROM DVD-106 1.22 PQ: 0 ANSI: 5 [ 33.740333] sr1: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray [ 33.740463] sr 2:0:1:0: Attached scsi CD-ROM sr1 [ 33.740483] sr 2:0:1:0: Attached scsi generic sg2 type 5 [ 33.755207] gameport: EMU10K1 is pci0000:01:08.1/gameport0, io 0xd000, speed 1203kHz [ 33.756094] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 [ 33.756205] IOAPIC[0]: Set PCI routing entry (2-18 -> 0x91 -> IRQ 18 Mode:1 Active:1) [ 33.756212] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18 [ 33.756454] ALSA sound/pci/emu10k1/emu10k1_main.c:1176: vendor=0x1102, device=0x2, subsystem_vendor_id=0x80641102, subsystem_id=0x8064 [ 33.756672] ALSA sound/pci/emu10k1/emu10k1_main.c:1201: Sound card name=SB Live 5.1 [ 34.141679] Adding 1951856k swap on /dev/sda6. Priority:-1 extents:1 across:1951856k [ 34.277758] EXT3 FS on sda5, internal journal [ 55.266834] kjournald starting. Commit interval 5 seconds [ 55.266842] EXT3-fs: mounted filesystem with ordered data mode. [ 55.293021] kjournald starting. Commit interval 5 seconds [ 55.293232] EXT3 FS on dm-2, internal journal [ 55.293235] EXT3-fs: mounted filesystem with ordered data mode. [ 55.316433] kjournald starting. Commit interval 5 seconds [ 55.316673] EXT3 FS on dm-1, internal journal [ 55.316676] EXT3-fs: mounted filesystem with ordered data mode. [ 55.345149] kjournald starting. Commit interval 5 seconds [ 55.345335] EXT3 FS on dm-3, internal journal [ 55.345338] EXT3-fs: mounted filesystem with ordered data mode. [ 55.362316] ReiserFS: dm-4: found reiserfs format "3.6" with standard journal [ 55.362324] ReiserFS: dm-4: using ordered data mode [ 55.366159] ReiserFS: dm-4: journal params: device dm-4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 55.367288] ReiserFS: dm-4: checking transaction log (dm-4) [ 55.408316] ReiserFS: dm-4: Using r5 hash to sort names [ 63.931903] lp: driver loaded but no devices found [ 63.938146] ppdev: user-space parallel port driver [ 65.473324] eth0: no IPv6 routers present [ 73.986381] [drm] Initialized drm 1.1.0 20060810 [ 74.019729] ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16 [ 74.019734] ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 16 [ 74.019789] [drm] Initialized radeon 1.25.0 20060524 on minor 0 [ 81.453161] [drm] Setting GART location based on new memory map [ 81.453299] [drm] Loading R300 Microcode [ 81.453314] [drm] writeback test succeeded in 1 usecs [ 4259.367578] Stopping tasks ... done. [ 4259.373241] Shrinking memory... -\|/-\|/-\|/-\done (132248 pages freed) [ 4259.824607] Freed 528992 kbytes in 0.36 seconds (1469.42 MB/s) [ 4259.824610] Suspending console(s) [ 4259.824667] pl2303 2-5:1.0: no suspend for driver pl2303? [ 4259.831337] ACPI: PCI interrupt for device 0000:01:08.0 disabled [ 4259.857319] ata4: port disabled. ignoring. [ 4259.857321] ata4: reset failed, giving up [ 4259.857348] ACPI: PCI interrupt for device 0000:00:02.1 disabled [ 4259.870614] ACPI: PCI interrupt for device 0000:00:02.0 disabled [ 4259.884150] Extended CMOS year: 20 [ 4259.884154] swsusp: critical section: [ 4259.901762] swsusp: Need to copy 126252 pages [ 46.617820] Extended CMOS year: 20 [ 46.741688] ACPI: Unable to turn cooling device [ffff81003fe90890] 'on' [ 46.754331] PCI: Enabling device 0000:00:02.0 (0000 -> 0002) [ 46.754336] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 22 [ 46.754341] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 46.754346] PM: Writing back config space on device 0000:00:02.0 at offset f (was 1030100, writing 103010a) [ 46.754353] PM: Writing back config space on device 0000:00:02.0 at offset 4 (was 0, writing fe02f000) [ 46.754357] PM: Writing back config space on device 0000:00:02.0 at offset 1 (was b00006, writing b00007) [ 46.767646] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 23 [ 46.767650] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 46.767663] usb usb1: root hub lost power or was reset [ 46.767670] ehci_hcd 0000:00:02.1: debug port 1 [ 46.767672] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 46.767680] PM: Writing back config space on device 0000:00:04.0 at offset b (was 82391043, writing 8239f043) [ 46.767687] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 46.767699] PCI: Setting latency timer of device 0000:00:06.0 to 64 [ 46.767731] ata4: port disabled. ignoring. [ 46.767733] ata4: reset failed, giving up [ 46.781633] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 46.781646] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 46.781658] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 46.781670] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 46.781682] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 46.781695] PCI: Setting latency timer of device 0000:00:0f.0 to 64 [ 46.794290] PM: Writing back config space on device 0000:01:08.0 at offset 1 (was 2900005, writing 2900001) [ 46.794300] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18 [ 46.802032] PCI: Setting latency timer of device 0000:06:00.0 to 64 [ 46.802087] ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 16 [ 46.802101] PM: Writing back config space on device 0000:07:00.1 at offset 1 (was 100000, writing 100004) [ 46.834236] usb usb2: root hub lost power or was reset [ 46.900814] usbdev1.2_ep00: PM: resume from 0, parent 1-2 still 1 [ 46.900817] hub 1-2:1.0: PM: resume from 1, parent 1-2 still 1 [ 46.900819] usbdev1.2_ep81: PM: resume from 0, parent 1-2:1.0 still 1 [ 46.900822] usbdev2.2_ep00: PM: resume from 0, parent 2-3 still 1 [ 46.900825] usb 2-3:1.0: PM: resume from 1, parent 2-3 still 1 [ 46.900827] usbdev2.2_ep81: PM: resume from 0, parent 2-3:1.0 still 1 [ 46.900830] usbdev2.2_ep02: PM: resume from 0, parent 2-3:1.0 still 1 [ 46.900833] usbdev2.3_ep00: PM: resume from 0, parent 2-5 still 1 [ 46.900836] pl2303 2-5:1.0: PM: resume from 1, parent 2-5 still 1 [ 46.900838] usbdev2.3_ep81: PM: resume from 0, parent 2-5:1.0 still 1 [ 46.900841] usbdev2.3_ep02: PM: resume from 0, parent 2-5:1.0 still 1 [ 46.900844] usbdev2.3_ep83: PM: resume from 0, parent 2-5:1.0 still 1 [ 46.900846] usb 1-2.3: PM: resume from 1, parent 1-2 still 1 [ 46.900849] usbdev1.5_ep00: PM: resume from 0, parent 1-2.3 still 1 [ 46.900852] usbhid 1-2.3:1.0: PM: resume from 1, parent 1-2.3 still 1 [ 46.900854] usbdev1.5_ep81: PM: resume from 0, parent 1-2.3:1.0 still 1 [ 46.900857] usb 1-2.4: PM: resume from 1, parent 1-2 still 1 [ 46.900859] usbdev1.6_ep00: PM: resume from 0, parent 1-2.4 still 1 [ 46.900862] usbhid 1-2.4:1.0: PM: resume from 1, parent 1-2.4 still 1 [ 46.900865] usbdev1.6_ep81: PM: resume from 0, parent 1-2.4:1.0 still 1 [ 46.900896] pl2303 ttyUSB0: PM: resume from 0, parent 2-5:1.0 still 1 [ 46.901647] Restarting tasks ... done. [ 47.370227] ata1: SATA link down (SStatus 0 SControl 300) [ 47.500058] usb 2-3: USB disconnect, address 2 [ 47.718451] usb 2-5: USB disconnect, address 3 [ 47.718536] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0 [ 47.718551] pl2303 2-5:1.0: device disconnected [ 48.180039] ata3.00: simplex DMA is claimed by other device, disabling DMA [ 48.180044] ata3.01: simplex DMA is claimed by other device, disabling DMA [ 48.233813] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 48.269054] ata2.00: configured for UDMA/133 [ 48.279925] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) [ 48.281181] sda: Write Protect is off [ 48.281183] sda: Mode Sense: 00 3a 00 00 [ 48.307427] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 48.323838] ata3.00: configured for PIO4 [ 48.365639] usb 1-2: USB disconnect, address 2 [ 48.365642] usb 1-2.3: USB disconnect, address 5 [ 48.365813] usb 1-2.4: USB disconnect, address 6 [ 48.467677] ata3.01: configured for PIO4 [ 48.569386] usb 1-2: new high speed USB device using ehci_hcd and address 7 [ 48.663586] usb 1-2: configuration #1 chosen from 1 choice [ 48.663742] hub 1-2:1.0: USB hub found [ 48.663915] hub 1-2:1.0: 4 ports detected [ 49.009453] usb 2-3: new full speed USB device using ohci_hcd and address 4 [ 49.084293] usb 2-3: configuration #1 chosen from 1 choice [ 49.205580] usb 2-5: new full speed USB device using ohci_hcd and address 5 [ 49.282050] usb 2-5: configuration #1 chosen from 1 choice [ 49.283535] pl2303 2-5:1.0: pl2303 converter detected [ 49.283578] usb 2-5: pl2303 converter now attached to ttyUSB0 [ 49.377140] usb 1-2.3: new low speed USB device using ehci_hcd and address 10 [ 49.421334] usb 1-2.3: configuration #1 chosen from 1 choice [ 49.423607] input: Logitech USB-PS/2 Optical Mouse as /class/input/input4 [ 49.423646] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.1-2.3 [ 49.516965] usb 1-2.4: new low speed USB device using ehci_hcd and address 11 [ 49.567151] usb 1-2.4: configuration #1 chosen from 1 choice [ 49.569434] input: HID 046a:0001 as /class/input/input5 [ 49.569461] input: USB HID v1.00 Keyboard [HID 046a:0001] on usb-0000:00:02.1-2.4 [ 51.357955] [drm] Loading R300 Microcode [ 1819.418095] Stopping tasks ... done. [ 1819.424178] Shrinking memory... -\<7>Losing some ticks... checking if CPU frequency changed. [ 1819.573548] |/-done (52819 pages freed) [ 1819.702523] Freed 211276 kbytes in 0.26 seconds (812.60 MB/s) [ 1819.702526] Suspending console(s) [ 1819.702542] pl2303 2-5:1.0: no suspend for driver pl2303? [ 1819.708649] ACPI: PCI interrupt for device 0000:01:08.0 disabled [ 1819.730573] ata4: port disabled. ignoring. [ 1819.730575] ata4: reset failed, giving up [ 1819.730600] ACPI: PCI interrupt for device 0000:00:02.1 disabled [ 1819.742539] ACPI: PCI interrupt for device 0000:00:02.0 disabled [ 1819.754724] Extended CMOS year: 20 [ 1819.754728] swsusp: critical section: [ 1819.771398] swsusp: Need to copy 119646 pages [ 45.092996] Extended CMOS year: 20 [ 45.227517] ACPI: Unable to turn cooling device [ffff81003fe90890] 'on' [ 45.239495] PCI: Enabling device 0000:00:02.0 (0000 -> 0002) [ 45.239499] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 22 [ 45.239505] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 45.239510] PM: Writing back config space on device 0000:00:02.0 at offset f (was 1030100, writing 103010a) [ 45.239517] PM: Writing back config space on device 0000:00:02.0 at offset 4 (was 0, writing fe02f000) [ 45.239521] PM: Writing back config space on device 0000:00:02.0 at offset 1 (was b00006, writing b00007) [ 45.252811] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 23 [ 45.252815] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 45.252827] usb usb1: root hub lost power or was reset [ 45.252834] ehci_hcd 0000:00:02.1: debug port 1 [ 45.252837] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 45.252848] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 45.252860] PCI: Setting latency timer of device 0000:00:06.0 to 64 [ 45.252892] ata4: port disabled. ignoring. [ 45.252894] ata4: reset failed, giving up [ 45.266802] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 45.266816] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 45.266829] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 45.266842] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 45.266854] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 45.266867] PCI: Setting latency timer of device 0000:00:0f.0 to 64 [ 45.279453] PM: Writing back config space on device 0000:01:08.0 at offset 1 (was 2900005, writing 2900001) [ 45.279463] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18 [ 45.287212] PCI: Setting latency timer of device 0000:06:00.0 to 64 [ 45.287267] ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 16 [ 45.287281] PM: Writing back config space on device 0000:07:00.1 at offset 1 (was 100000, writing 100004) [ 45.319399] usb usb2: root hub lost power or was reset [ 45.386014] usbdev1.7_ep00: PM: resume from 0, parent 1-2 still 1 [ 45.386017] hub 1-2:1.0: PM: resume from 1, parent 1-2 still 1 [ 45.386020] usbdev1.7_ep81: PM: resume from 0, parent 1-2:1.0 still 1 [ 45.386023] usbdev2.4_ep00: PM: resume from 0, parent 2-3 still 1 [ 45.386025] usb 2-3:1.0: PM: resume from 1, parent 2-3 still 1 [ 45.386028] usbdev2.4_ep81: PM: resume from 0, parent 2-3:1.0 still 1 [ 45.386030] usbdev2.4_ep02: PM: resume from 0, parent 2-3:1.0 still 1 [ 45.386033] usbdev2.5_ep00: PM: resume from 0, parent 2-5 still 1 [ 45.386036] pl2303 2-5:1.0: PM: resume from 1, parent 2-5 still 1 [ 45.386039] pl2303 ttyUSB0: PM: resume from 0, parent 2-5:1.0 still 1 [ 45.386042] usbdev2.5_ep81: PM: resume from 0, parent 2-5:1.0 still 1 [ 45.386045] usbdev2.5_ep02: PM: resume from 0, parent 2-5:1.0 still 1 [ 45.386047] usbdev2.5_ep83: PM: resume from 0, parent 2-5:1.0 still 1 [ 45.386050] usb 1-2.3: PM: resume from 1, parent 1-2 still 1 [ 45.386053] usbdev1.10_ep00: PM: resume from 0, parent 1-2.3 still 1 [ 45.386055] usbhid 1-2.3:1.0: PM: resume from 1, parent 1-2.3 still 1 [ 45.386058] usbdev1.10_ep81: PM: resume from 0, parent 1-2.3:1.0 still 1 [ 45.386061] usb 1-2.4: PM: resume from 1, parent 1-2 still 1 [ 45.386064] usbdev1.11_ep00: PM: resume from 0, parent 1-2.4 still 1 [ 45.386066] usbhid 1-2.4:1.0: PM: resume from 1, parent 1-2.4 still 1 [ 45.386069] usbdev1.11_ep81: PM: resume from 0, parent 1-2.4:1.0 still 1 [ 45.386808] Restarting tasks ... done. [ 45.908656] ata1: SATA link down (SStatus 0 SControl 300) [ 46.038488] usb 2-3: USB disconnect, address 4 [ 46.278183] usb 2-5: USB disconnect, address 5 [ 46.278290] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0 [ 46.278302] pl2303 2-5:1.0: device disconnected [ 46.709405] ata3.00: simplex DMA is claimed by other device, disabling DMA [ 46.709410] ata3.01: simplex DMA is claimed by other device, disabling DMA [ 46.739271] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 46.760624] ata2.00: configured for UDMA/133 [ 46.766708] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) [ 46.770504] sda: Write Protect is off [ 46.770508] sda: Mode Sense: 00 3a 00 00 [ 46.789290] ata3.00: configured for PIO4 [ 46.830671] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 46.839142] usb 1-2: USB disconnect, address 7 [ 46.839145] usb 1-2.3: USB disconnect, address 10 [ 46.839351] usb 1-2.4: USB disconnect, address 11 [ 46.869204] ata3.01: configured for PIO4 [ 46.952330] usb 1-2: new high speed USB device using ehci_hcd and address 12 [ 47.014599] usb 1-2: configuration #1 chosen from 1 choice [ 47.014751] hub 1-2:1.0: USB hub found [ 47.014919] hub 1-2:1.0: 4 ports detected [ 47.360147] usb 2-3: new full speed USB device using ohci_hcd and address 6 [ 47.435407] usb 2-3: configuration #1 chosen from 1 choice [ 47.554902] usb 2-5: new full speed USB device using ohci_hcd and address 7 [ 47.631378] usb 2-5: configuration #1 chosen from 1 choice [ 47.632858] pl2303 2-5:1.0: pl2303 converter detected [ 47.632900] usb 2-5: pl2303 converter now attached to ttyUSB0 [ 47.726463] usb 1-2.3: new low speed USB device using ehci_hcd and address 15 [ 47.770717] usb 1-2.3: configuration #1 chosen from 1 choice [ 47.772246] input: Logitech USB-PS/2 Optical Mouse as /class/input/input6 [ 47.772275] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.1-2.3 [ 47.866288] usb 1-2.4: new low speed USB device using ehci_hcd and address 16 [ 47.916470] usb 1-2.4: configuration #1 chosen from 1 choice [ 47.918585] input: HID 046a:0001 as /class/input/input7 [ 47.918613] input: USB HID v1.00 Keyboard [HID 046a:0001] on usb-0000:00:02.1-2.4 [ 49.715588] [drm] Loading R300 Microcode [11140.947574] Stopping tasks ... done. [11140.951996] Shrinking memory... -\|/-\|/-\|/-done (126350 pages freed) [11141.387165] Freed 505400 kbytes in 0.37 seconds (1365.94 MB/s) [11141.387168] Suspending console(s) [11141.387183] pl2303 2-5:1.0: no suspend for driver pl2303? [11141.393260] ACPI: PCI interrupt for device 0000:01:08.0 disabled [11141.416988] ata4: port disabled. ignoring. [11141.416990] ata4: reset failed, giving up [11141.417015] ACPI: PCI interrupt for device 0000:00:02.1 disabled [11141.428954] ACPI: PCI interrupt for device 0000:00:02.0 disabled [11141.441138] Extended CMOS year: 20 [11141.441142] swsusp: critical section: [11141.458212] swsusp: Need to copy 125968 pages [ 46.405801] Extended CMOS year: 20 [ 46.526479] ACPI: Unable to turn cooling device [ffff81003fe90890] 'on' [ 46.538984] PCI: Enabling device 0000:00:02.0 (0000 -> 0002) [ 46.538988] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 22 [ 46.538993] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 46.538998] PM: Writing back config space on device 0000:00:02.0 at offset f (was 1030100, writing 103010a) [ 46.539005] PM: Writing back config space on device 0000:00:02.0 at offset 4 (was 0, writing fe02f000) [ 46.539009] PM: Writing back config space on device 0000:00:02.0 at offset 1 (was b00006, writing b00007) [ 46.552299] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 23 [ 46.552303] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 46.552315] usb usb1: root hub lost power or was reset [ 46.552322] ehci_hcd 0000:00:02.1: debug port 1 [ 46.552325] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 46.552336] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 46.552348] PCI: Setting latency timer of device 0000:00:06.0 to 64 [ 46.552380] ata4: port disabled. ignoring. [ 46.552381] ata4: reset failed, giving up [ 46.566291] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 46.566304] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 46.566317] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 46.566329] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 46.566342] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 46.566354] PCI: Setting latency timer of device 0000:00:0f.0 to 64 [ 46.578942] PM: Writing back config space on device 0000:01:08.0 at offset 1 (was 2900005, writing 2900001) [ 46.578952] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18 [ 46.586654] PCI: Setting latency timer of device 0000:06:00.0 to 64 [ 46.586708] ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 16 [ 46.586722] PM: Writing back config space on device 0000:07:00.1 at offset 1 (was 100000, writing 100004) [ 46.618888] usb usb2: root hub lost power or was reset [ 46.685502] usbdev1.12_ep00: PM: resume from 0, parent 1-2 still 1 [ 46.685505] hub 1-2:1.0: PM: resume from 1, parent 1-2 still 1 [ 46.685508] usbdev1.12_ep81: PM: resume from 0, parent 1-2:1.0 still 1 [ 46.685511] usbdev2.6_ep00: PM: resume from 0, parent 2-3 still 1 [ 46.685513] usb 2-3:1.0: PM: resume from 1, parent 2-3 still 1 [ 46.685516] usbdev2.6_ep81: PM: resume from 0, parent 2-3:1.0 still 1 [ 46.685519] usbdev2.6_ep02: PM: resume from 0, parent 2-3:1.0 still 1 [ 46.685522] usbdev2.7_ep00: PM: resume from 0, parent 2-5 still 1 [ 46.685524] pl2303 2-5:1.0: PM: resume from 1, parent 2-5 still 1 [ 46.685527] pl2303 ttyUSB0: PM: resume from 0, parent 2-5:1.0 still 1 [ 46.685530] usbdev2.7_ep81: PM: resume from 0, parent 2-5:1.0 still 1 [ 46.685533] usbdev2.7_ep02: PM: resume from 0, parent 2-5:1.0 still 1 [ 46.685535] usbdev2.7_ep83: PM: resume from 0, parent 2-5:1.0 still 1 [ 46.685538] usb 1-2.3: PM: resume from 1, parent 1-2 still 1 [ 46.685541] usbdev1.15_ep00: PM: resume from 0, parent 1-2.3 still 1 [ 46.685543] usbhid 1-2.3:1.0: PM: resume from 1, parent 1-2.3 still 1 [ 46.685546] usbdev1.15_ep81: PM: resume from 0, parent 1-2.3:1.0 still 1 [ 46.685549] usb 1-2.4: PM: resume from 1, parent 1-2 still 1 [ 46.685551] usbdev1.16_ep00: PM: resume from 0, parent 1-2.4 still 1 [ 46.685554] usbhid 1-2.4:1.0: PM: resume from 1, parent 1-2.4 still 1 [ 46.685557] usbdev1.16_ep81: PM: resume from 0, parent 1-2.4:1.0 still 1 [ 46.687133] Restarting tasks ... done. [ 47.154878] ata1: SATA link down (SStatus 0 SControl 300) [ 47.284708] usb 2-3: USB disconnect, address 6 [ 47.512421] usb 2-5: USB disconnect, address 7 [ 47.512514] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0 [ 47.512529] pl2303 2-5:1.0: device disconnected [ 47.974011] ata3.00: simplex DMA is claimed by other device, disabling DMA [ 47.974016] ata3.01: simplex DMA is claimed by other device, disabling DMA [ 48.027783] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 48.061190] ata2.00: configured for UDMA/133 [ 48.069834] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) [ 48.074885] sda: Write Protect is off [ 48.074887] sda: Mode Sense: 00 3a 00 00 [ 48.092079] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 48.117809] ata3.00: configured for PIO4 [ 48.159611] usb 1-2: USB disconnect, address 12 [ 48.159613] usb 1-2.3: USB disconnect, address 15 [ 48.159799] usb 1-2.4: USB disconnect, address 16 [ 48.261649] ata3.01: configured for PIO4 [ 48.363361] usb 1-2: new high speed USB device using ehci_hcd and address 17 [ 48.475357] usb 1-2: configuration #1 chosen from 1 choice [ 48.475546] hub 1-2:1.0: USB hub found [ 48.475862] hub 1-2:1.0: 4 ports detected [ 48.840712] usb 2-3: new full speed USB device using ohci_hcd and address 8 [ 48.915559] usb 2-3: configuration #1 chosen from 1 choice [ 49.036838] usb 2-5: new full speed USB device using ohci_hcd and address 9 [ 49.113312] usb 2-5: configuration #1 chosen from 1 choice [ 49.114796] pl2303 2-5:1.0: pl2303 converter detected [ 49.114839] usb 2-5: pl2303 converter now attached to ttyUSB0 [ 49.208399] usb 1-2.3: new low speed USB device using ehci_hcd and address 20 [ 49.252655] usb 1-2.3: configuration #1 chosen from 1 choice [ 49.254306] input: Logitech USB-PS/2 Optical Mouse as /class/input/input8 [ 49.254334] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.1-2.3 [ 49.348225] usb 1-2.4: new low speed USB device using ehci_hcd and address 21 [ 49.398410] usb 1-2.4: configuration #1 chosen from 1 choice [ 49.400547] input: HID 046a:0001 as /class/input/input9 [ 49.400574] input: USB HID v1.00 Keyboard [HID 046a:0001] on usb-0000:00:02.1-2.4 [ 51.888316] [drm] Loading R300 Microcode [ 1868.638886] Stopping tasks ... done. [ 1868.648496] Shrinking memory... -\|done (37345 pages freed) [ 1868.916749] Freed 149380 kbytes in 0.24 seconds (622.41 MB/s) [ 1868.916752] Suspending console(s) [ 1868.916768] pl2303 2-5:1.0: no suspend for driver pl2303? [ 1868.923494] ACPI: PCI interrupt for device 0000:01:08.0 disabled [ 1868.949070] ata4: port disabled. ignoring. [ 1868.949073] ata4: reset failed, giving up [ 1868.949099] ACPI: PCI interrupt for device 0000:00:02.1 disabled [ 1868.962366] ACPI: PCI interrupt for device 0000:00:02.0 disabled [ 1868.975902] Extended CMOS year: 20 [ 1868.975905] swsusp: critical section: [ 1868.992230] swsusp: Need to copy 118066 pages [ 45.033129] Extended CMOS year: 20 [ 45.102696] ACPI: Unable to turn cooling device [ffff81003fe90890] 'on' [ 45.113046] PCI: Enabling device 0000:00:02.0 (0000 -> 0002) [ 45.113050] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 22 [ 45.113056] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 45.113061] PM: Writing back config space on device 0000:00:02.0 at offset f (was 1030100, writing 103010a) [ 45.113067] PM: Writing back config space on device 0000:00:02.0 at offset 4 (was 0, writing fe02f000) [ 45.113072] PM: Writing back config space on device 0000:00:02.0 at offset 1 (was b00006, writing b00007) [ 45.121372] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 23 [ 45.121376] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 45.121385] usb usb1: root hub lost power or was reset [ 45.121390] ehci_hcd 0000:00:02.1: debug port 1 [ 45.121392] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 45.121401] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 45.121411] PCI: Setting latency timer of device 0000:00:06.0 to 64 [ 45.121434] ata4: port disabled. ignoring. [ 45.121435] ata4: reset failed, giving up [ 45.128447] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 45.128458] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 45.128468] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 45.128478] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 45.128488] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 45.128498] PCI: Setting latency timer of device 0000:00:0f.0 to 64 [ 45.134697] PM: Writing back config space on device 0000:01:08.0 at offset 1 (was 2900005, writing 2900001) [ 45.134705] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18 [ 45.138897] PCI: Setting latency timer of device 0000:06:00.0 to 64 [ 45.138930] ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 16 [ 45.138940] PM: Writing back config space on device 0000:07:00.1 at offset 1 (was 100000, writing 100004) [ 45.154668] usb usb2: root hub lost power or was reset [ 45.187980] usbdev1.17_ep00: PM: resume from 0, parent 1-2 still 1 [ 45.187983] hub 1-2:1.0: PM: resume from 1, parent 1-2 still 1 [ 45.187985] usbdev1.17_ep81: PM: resume from 0, parent 1-2:1.0 still 1 [ 45.187988] usbdev2.8_ep00: PM: resume from 0, parent 2-3 still 1 [ 45.187991] usb 2-3:1.0: PM: resume from 1, parent 2-3 still 1 [ 45.187994] usbdev2.8_ep81: PM: resume from 0, parent 2-3:1.0 still 1 [ 45.187996] usbdev2.8_ep02: PM: resume from 0, parent 2-3:1.0 still 1 [ 45.187999] usbdev2.9_ep00: PM: resume from 0, parent 2-5 still 1 [ 45.188002] pl2303 2-5:1.0: PM: resume from 1, parent 2-5 still 1 [ 45.188005] pl2303 ttyUSB0: PM: resume from 0, parent 2-5:1.0 still 1 [ 45.188007] usbdev2.9_ep81: PM: resume from 0, parent 2-5:1.0 still 1 [ 45.188010] usbdev2.9_ep02: PM: resume from 0, parent 2-5:1.0 still 1 [ 45.188013] usbdev2.9_ep83: PM: resume from 0, parent 2-5:1.0 still 1 [ 45.188016] usb 1-2.3: PM: resume from 1, parent 1-2 still 1 [ 45.188018] usbdev1.20_ep00: PM: resume from 0, parent 1-2.3 still 1 [ 45.188021] usbhid 1-2.3:1.0: PM: resume from 1, parent 1-2.3 still 1 [ 45.188024] usbdev1.20_ep81: PM: resume from 0, parent 1-2.3:1.0 still 1 [ 45.188027] usb 1-2.4: PM: resume from 1, parent 1-2 still 1 [ 45.188029] usbdev1.21_ep00: PM: resume from 0, parent 1-2.4 still 1 [ 45.188032] usbhid 1-2.4:1.0: PM: resume from 1, parent 1-2.4 still 1 [ 45.188035] usbdev1.21_ep81: PM: resume from 0, parent 1-2.4:1.0 still 1 [ 45.189668] Restarting tasks ... done. [ 45.427658] ata1: SATA link down (SStatus 0 SControl 300) [ 45.492574] usb 2-3: USB disconnect, address 8 [ 45.612423] usb 2-5: USB disconnect, address 9 [ 45.612522] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0 [ 45.612534] pl2303 2-5:1.0: device disconnected [ 45.862207] ata3.00: simplex DMA is claimed by other device, disabling DMA [ 45.862212] ata3.01: simplex DMA is claimed by other device, disabling DMA [ 45.892076] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 45.909792] ata2.00: configured for UDMA/133 [ 45.917258] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) [ 45.919786] sda: Write Protect is off [ 45.919789] sda: Mode Sense: 00 3a 00 00 [ 45.942097] ata3.00: configured for PIO4 [ 45.963270] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 45.971972] usb 1-2: USB disconnect, address 17 [ 45.971975] usb 1-2.3: USB disconnect, address 20 [ 45.972182] usb 1-2.4: USB disconnect, address 21 [ 46.022005] ata3.01: configured for PIO4 [ 46.085160] usb 1-2: new high speed USB device using ehci_hcd and address 22 [ 46.147417] usb 1-2: configuration #1 chosen from 1 choice [ 46.147568] hub 1-2:1.0: USB hub found [ 46.147737] hub 1-2:1.0: 4 ports detected [ 46.492976] usb 2-3: new full speed USB device using ohci_hcd and address 10 [ 46.568121] usb 2-3: configuration #1 chosen from 1 choice [ 46.689693] usb 2-5: new full speed USB device using ohci_hcd and address 11 [ 46.765875] usb 2-5: configuration #1 chosen from 1 choice [ 46.767359] pl2303 2-5:1.0: pl2303 converter detected [ 46.767401] usb 2-5: pl2303 converter now attached to ttyUSB0 [ 46.860966] usb 1-2.3: new low speed USB device using ehci_hcd and address 25 [ 46.905221] usb 1-2.3: configuration #1 chosen from 1 choice [ 46.906812] input: Logitech USB-PS/2 Optical Mouse as /class/input/input10 [ 46.906840] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.1-2.3 [ 47.000791] usb 1-2.4: new low speed USB device using ehci_hcd and address 26 [ 47.050975] usb 1-2.4: configuration #1 chosen from 1 choice [ 47.053263] input: HID 046a:0001 as /class/input/input11 [ 47.053291] input: USB HID v1.00 Keyboard [HID 046a:0001] on usb-0000:00:02.1-2.4 [ 48.843424] [drm] Loading R300 Microcode [ 5527.919787] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 5527.921129] ISO 9660 Extensions: RRIP_1991A [ 5543.460247] ata3.00: disabled [ 5543.460251] ata3.01: disabled [ 5543.463584] Trying to free nonexistent resource <00000000000001f0-00000000000001f7> [ 5543.463588] Trying to free nonexistent resource <0000000000000170-0000000000000177> [ 5544.447160] pata_amd 0000:00:04.0: version 0.2.7 [ 5544.447173] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 5544.450745] ata5: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14 [ 5544.451229] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15 [ 5544.451245] scsi4 : pata_amd [ 5544.607725] ata5.00: ATAPI, max UDMA/33 [ 5544.687551] ata5.01: ATAPI, max UDMA/66 [ 5544.767439] ata5.00: configured for UDMA/33 [ 5544.847348] ata5.01: configured for UDMA/33 [ 5544.847819] scsi5 : pata_amd [ 5544.847869] ata6: port disabled. ignoring. [ 5544.847871] ata6: reset failed, giving up [ 5544.853145] scsi 4:0:0:0: CD-ROM _NEC DVD_RW ND-3500AG 2.1A PQ: 0 ANSI: 5 [ 5544.855207] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray [ 5544.855243] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 5544.855271] sr 4:0:0:0: Attached scsi generic sg1 type 5 [ 5544.857560] scsi 4:0:1:0: CD-ROM PIONEER DVD-ROM DVD-106 1.22 PQ: 0 ANSI: 5 [ 5544.862326] sr1: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray [ 5544.862366] sr 4:0:1:0: Attached scsi CD-ROM sr1 [ 5544.862397] sr 4:0:1:0: Attached scsi generic sg2 type 5 [ 5547.650288] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 5547.651829] ISO 9660 Extensions: RRIP_1991A [ 5573.214514] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 5573.215370] ISO 9660 Extensions: RRIP_1991A [ 6413.972484] EXT3 FS on sda1, internal journal [ 6481.731596] EXT3 FS on sda1, internal journal [ 8025.835826] time.c: can't update CMOS clock from 59 to 0 [10031.009704] ISO 9660 Extensions: Microsoft Joliet Level 3 [10031.032879] ISO 9660 Extensions: RRIP_1991A -- Tobias PGP: http://9ac7e0bc.uguu.de このメールは十割再利用されたビットで作られています。 - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
