Hi All,
I got asked to forward this email I sent to the lkml to here :)
So that's what I do.
The problem below exists with 2.6.20-git11 and the Jeff's libata-dev
linus-upstream tree, which I cloned yesterday evening at the unholy
hour of 00:10 GMT
I am not on the ide list, so if you could CC me in anything regarding
my problem I'd be very thankfull :)
I attached a complete dmesg output.
Patrick
---------- Forwarded message ----------
From: Patrick Ale <patrick.ale@xxxxxxxxx>
Date: Feb 15, 2007 9:52 AM
Subject: Re: [LIBATA] drives not detected
To: linux-kernel <linux-kernel@xxxxxxxxxxxxxxx>
On 2/15/07, Patrick Ale <patrick.ale@xxxxxxxxx> wrote:
Good morning all,
Now, when I boot up, I miss two drives, exactly the two connected to
this promise card.
I have another onboard Promise controller which works just fine, so
the driver gets loaded properly, and since i see all my other disks
but these two I think we can rule out a misconfiguration of the kernel
config this time ;-)
It would be nice if I'd also mention the kernel I use eh.
It's linux-2.6-git8
Patrick
Linux version 2.6.20-g66efc5a7 (root@localhost) (gcc version 3.4.6 (Gentoo 3.4.6-r2, ssp-3.4.6-1.0, pie-8.7.10)) #1 PREEMPT Wed Feb 14 15:20:37 GMT 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 00000000bfef0000 end: 00000000bfff0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 00000000bfff0000 size: 0000000000003000 end: 00000000bfff3000 type: 4
copy_e820_map() start: 00000000bfff3000 size: 000000000000d000 end: 00000000c0000000 type: 3
copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2
copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
copy_e820_map() start: 00000000ffff0000 size: 0000000000010000 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable)
BIOS-e820: 00000000bfff0000 - 00000000bfff3000 (ACPI NVS)
BIOS-e820: 00000000bfff3000 - 00000000c0000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
2175MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f4c30
Entering add_active_range(0, 0, 786416) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 786416
early_node_map[1] active PFN ranges
0: 0 -> 786416
On node 0 totalpages: 786416
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 4351 pages used for memmap
HighMem zone: 552689 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP 000F65A0, 0014 (r0 GBT )
ACPI: RSDT BFFF3000, 002C (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
ACPI: FACP BFFF3040, 0074 (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
ACPI: DSDT BFFF30C0, 3BD9 (r1 GBT AWRDACPI 1000 MSFT 100000C)
ACPI: FACS BFFF0000, 0040
ACPI: APIC BFFF6CC0, 005A (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c4000000 (gap: c0000000:3ec00000)
Detected 2009.482 MHz processor.
Built 1 zonelists. Total pages: 780273
Kernel command line: root=/dev/sda3
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3114512k/3145664k available (3001k kernel code, 30084k reserved, 999k data, 196k init, 2228160k highmem)
virtual kernel memory layout:
fixmap : 0xfffaa000 - 0xfffff000 ( 340 kB)
pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
vmalloc : 0xf8800000 - 0xffbfe000 ( 115 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc04ec000 - 0xc051d000 ( 196 kB)
.data : 0xc03ee529 - 0xc04e830c ( 999 kB)
.text : 0xc0100000 - 0xc03ee529 (3001 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4020.84 BogoMIPS (lpj=2010422)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: AMD Athlon(tm) XP 2400+ stepping 01
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf9ee0, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 4000-407f claimed by vt8235 PM
PCI quirk: region 5000-500f claimed by vt8235 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 *6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0
SCSI subsystem initialized
libata version 2.10 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
ACPI: PCI Interrupt 0000:00:14.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[eb00c000-eb00c7ff] Max Packet=[2048] IR/IT contexts=[8/8]
PCI: Bridge: 0000:00:01.0
IO window: 7000-7fff
MEM window: e8000000-e9ffffff
PREFETCH window: c0000000-dfffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
microcode: CPU0 not a capable Intel processor
IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx>
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
SGI XFS with ACLs, realtime, large block numbers, no debug enabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: Retrieved PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=398.25 Mhz, System=200.00 MHz
radeonfb: PLL min 20000 max 40000
i2c_adapter i2c-1: unable to read EDID block.
i2c_adapter i2c-1: unable to read EDID block.
i2c_adapter i2c-1: unable to read EDID block.
radeonfb: Monitor 1 type CRT found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
Console: switching to colour frame buffer device 160x64
radeonfb (0000:01:00.0): ATI Radeon AP
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using get_cycles().
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
loop: loaded (max 8 devices)
pata_via 0000:00:11.1: version 0.2.1
ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 17
ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001dc00 irq 14
ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001dc08 irq 15
scsi0 : pata_via
ata1.00: ATA-6: WDC WD2000JB-00GVA0, 08.02D08, max UDMA/100
ata1.00: 390721968 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
scsi1 : pata_via
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000020ed006adc65]
scsi 0:0:0:0: Direct-Access ATA WDC WD2000JB-00G 08.0 PQ: 0 ANSI: 5
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
ieee1394: raw1394: /dev/raw1394 device initialized
ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: irq 18, io mem 0xeb00a000
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 18, io base 0x0000d000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 18, io base 0x0000d400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 18, io base 0x0000d800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-4: new high speed USB device using ehci_hcd and address 3
usb 1-4: configuration #1 chosen from 1 choice
usb 2-1: new low speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:10.0-1
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input3
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
oprofile: using NMI interrupt.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Time: tsc clocksource has been installed.
md: Autodetecting RAID arrays.
Time: acpi_pm clocksource has been installed.
md: autorun ...
md: ... autorun DONE.
XFS mounting filesystem sda3
Ending clean XFS mount for filesystem: sda3
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 196k freed
sd 0:0:0:0: Attached scsi generic sg0 type 0
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 19
eth0: RealTek RTL8139 at 0xf884a000, 00:20:ed:61:8a:9c, IRQ 19
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
pata_pdc2027x 0000:00:0b.0: version 0.74-ac5
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 20
pata_pdc2027x 0000:00:0b.0: PLL input clock 16754 kHz
ata3: PATA max UDMA/133 cmd 0xf88597c0 ctl 0xf8859fda bmdma 0xf8859000 irq 20
ata4: PATA max UDMA/133 cmd 0xf88595c0 ctl 0xf8859dda bmdma 0xf8859008 irq 20
scsi2 : pata_pdc2027x
input: PC Speaker as /class/input/input4
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 4:0:0:0: Direct-Access USB2.0 CardReader CF RW 0.0> PQ: 0 ANSI: 0
sd 4:0:0:0: Attached scsi removable disk sdb
sd 4:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
scsi3 : pata_pdc2027x
ATA: abnormal status 0x8 on port 0xf88595df
pata_sil680 0000:00:0c.0: version 0.4.1
sil680: BA5_EN = 1 clock = 00
sil680: BA5_EN = 1 clock = 10
sil680: 133MHz clock.
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 16 (level, low) -> IRQ 16
ata5: PATA max UDMA/133 cmd 0x0001a800 ctl 0x0001ac02 bmdma 0x0001b800 irq 16
ata6: PATA max UDMA/133 cmd 0x0001b000 ctl 0x0001b402 bmdma 0x0001b808 irq 16
scsi5 : pata_sil680
ata5.00: ATA-6: WDC WD1200JB-00EVA0, 15.05R15, max UDMA/100
ata5.00: 234441648 sectors, multi 0: LBA48
ata5.01: ATA-7: Maxtor 6L250R0, BAH41E00, max UDMA/133
ata5.01: 490234752 sectors, multi 0: LBA48
ata5.00: configured for UDMA/100
ata5.01: configured for UDMA/133
scsi6 : pata_sil680
ata6.00: ATA-6: WDC WD1600JB-00EVA0, 15.05R15, max UDMA/100
ata6.00: 312581808 sectors, multi 0: LBA48
ata6.00: configured for UDMA/100
scsi 5:0:0:0: Direct-Access ATA WDC WD1200JB-00E 15.0 PQ: 0 ANSI: 5
SCSI device sdc: 234441648 512-byte hdwr sectors (120034 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdc: 234441648 512-byte hdwr sectors (120034 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 5:0:0:0: Attached scsi disk sdc
sd 5:0:0:0: Attached scsi generic sg2 type 0
scsi 5:0:1:0: Direct-Access ATA Maxtor 6L250R0 BAH4 PQ: 0 ANSI: 5
SCSI device sdd: 490234752 512-byte hdwr sectors (251000 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdd: 490234752 512-byte hdwr sectors (251000 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 5:0:1:0: Attached scsi disk sdd
sd 5:0:1:0: Attached scsi generic sg3 type 0
scsi 6:0:0:0: Direct-Access ATA WDC WD1600JB-00E 15.0 PQ: 0 ANSI: 5
SCSI device sde: 312581808 512-byte hdwr sectors (160042 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sde: 312581808 512-byte hdwr sectors (160042 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 6:0:0:0: Attached scsi disk sde
sd 6:0:0:0: Attached scsi generic sg4 type 0
sata_sil 0000:00:08.0: version 2.0
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 17 (level, low) -> IRQ 21
ata7: SATA max UDMA/100 cmd 0xf8874080 ctl 0xf887408a bmdma 0xf8874000 irq 21
ata8: SATA max UDMA/100 cmd 0xf88740c0 ctl 0xf88740ca bmdma 0xf8874008 irq 21
scsi7 : sata_sil
ata7: SATA link down (SStatus 0 SControl 310)
scsi8 : sata_sil
ata8: SATA link down (SStatus 0 SControl 310)
ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:11.5 to 64
ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 19 (level, low) -> IRQ 20
pata_pdc2027x 0000:00:0f.0: PLL input clock 33508 kHz
ata9: PATA max UDMA/133 cmd 0xf98a97c0 ctl 0xf98a9fda bmdma 0xf98a9000 irq 20
ata10: PATA max UDMA/133 cmd 0xf98a95c0 ctl 0xf98a9dda bmdma 0xf98a9008 irq 20
scsi9 : pata_pdc2027x
ata9.00: ATA-7: Maxtor 6Y160P0, YAR41BW0, max UDMA/133
ata9.00: 320173056 sectors, multi 16: LBA48
ata9.01: ATA-6: WDC WD1200JB-00DUA3, 75.13B75, max UDMA/100
ata9.01: 234441648 sectors, multi 16: LBA48
ata9.00: configured for UDMA/133
ata9.01: configured for UDMA/100
scsi10 : pata_pdc2027x
ATA: abnormal status 0x78 on port 0xf98a95df
scsi 9:0:0:0: Direct-Access ATA Maxtor 6Y160P0 YAR4 PQ: 0 ANSI: 5
SCSI device sdf: 320173056 512-byte hdwr sectors (163929 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdf: 320173056 512-byte hdwr sectors (163929 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdf: sdf1
sd 9:0:0:0: Attached scsi disk sdf
sd 9:0:0:0: Attached scsi generic sg5 type 0
scsi 9:0:1:0: Direct-Access ATA WDC WD1200JB-00D 75.1 PQ: 0 ANSI: 5
SCSI device sdg: 234441648 512-byte hdwr sectors (120034 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdg: 234441648 512-byte hdwr sectors (120034 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdg: sdg1
sd 9:0:1:0: Attached scsi disk sdg
sd 9:0:1:0: Attached scsi generic sg6 type 0
md: md1 stopped.
md: bind<sdg1>
md: md2 stopped.
md: bind<sdc1>
md: md3 stopped.
md: bind<sdf1>
raid1: raid set md3 active with 1 out of 2 mirrors
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx
XFS mounting filesystem sda6
Ending clean XFS mount for filesystem: sda6
Adding 5863716k swap on /dev/disk/by-id/scsi-SATA_WDC_WD2000JB-00_WD-WCAL81971867-part2. Priority:-1 extents:1 across:5863716k
i2c_adapter i2c-2: sendbytes: error - bailout.
it87: Found IT8705F chip at 0x290, revision 2
it87-isa 9191-0290: Detected broken BIOS defaults, disabling PWM interface
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
