Hi,
I got this SATA PCI card:
00:04.0 Mass storage controller: ALi Corporation ALi M5281 Serial ATA / RAID
Host Controller (rev a4) (prog-if 85)
Subsystem: ALi Corporation ALi M5281 Serial ATA / RAID Host
Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128, Cache Line Size: 512 bytes
Interrupt: pin A routed to IRQ 185
Region 0: I/O ports at d400 [size=8]
Region 1: I/O ports at d000 [size=4]
Region 2: I/O ports at b800 [size=8]
Region 3: I/O ports at b400 [size=4]
Region 4: I/O ports at b000 [size=16]
[virtual] Expansion ROM at 88000000 [disabled] [size=64K]
00:04.1 Mass storage controller: ALi Corporation M5228 ALi ATA/RAID
Controller (rev c6) (prog-if 85)
Subsystem: ALi Corporation Unknown device 5281
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at a800 [size=8]
Region 1: I/O ports at a400 [size=4]
Region 2: I/O ports at a000 [size=8]
Region 3: I/O ports at 9800 [size=4]
Region 4: I/O ports at 9400 [size=16]
It worked very well for half a year but with one disk (IIRC it was even
plugged into second channel but I wont bet on it). Now I have second disk
(very similar) and it is always put into PIO4 mode:
[ 17.404451] libata version 2.00 loaded.
[ 17.404916] sata_uli 0000:00:04.0: version 1.0
[ 17.405009] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 18 (level, low)
-> IRQ 185
[ 17.405223] ata1: SATA max UDMA/133 cmd 0xD400 ctl 0xD002 bmdma 0xB000 irq
185
[ 17.405385] ata2: SATA max UDMA/133 cmd 0xB800 ctl 0xB402 bmdma 0xB008 irq
185
[ 17.405519] scsi2 : sata_uli
[ 17.858803] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 17.880541] ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ
(depth 0/32)
[ 17.880660] ata1.00: ata1: dev 0 multi count 16
[ 17.888858] ata1.00: configured for UDMA/133
[ 17.888941] scsi3 : sata_uli
[ 18.342469] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 18.343573] ata2.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ
(depth 0/32)
[ 18.343691] ata2.00: ata2: dev 0 multi count 16
[ 18.344972] ata2.00: configured for PIO4
[ 18.345466] Vendor: ATA Model: ST3250620NS Rev: 3.AE
[ 18.346391] Type: Direct-Access ANSI SCSI
revision: 05
[ 18.347464] Vendor: ATA Model: ST3250620NS Rev: 3.AE
[ 18.348390] Type: Direct-Access ANSI SCSI
revision: 05
[ 18.349457] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
[ 18.350234] sda: Write Protect is off
[ 18.350307] sda: Mode Sense: 00 3a 00 00
[ 18.351234] SCSI device sda: drive cache: write back
[ 18.352233] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
[ 18.352444] sda: Write Protect is off
[ 18.352517] sda: Mode Sense: 00 3a 00 00
[ 18.353443] SCSI device sda: drive cache: write back
[ 18.353522] sda: sda1 sda2
[ 18.371118] sd 2:0:0:0: Attached scsi disk sda
[ 18.372221] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
[ 18.372431] sdb: Write Protect is off
[ 18.372504] sdb: Mode Sense: 00 3a 00 00
[ 18.373440] SCSI device sdb: drive cache: write back
[ 18.374430] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
[ 18.375218] sdb: Write Protect is off
[ 18.375291] sdb: Mode Sense: 00 3a 00 00
[ 18.376216] SCSI device sdb: drive cache: write back
[ 18.376295] sdb: unknown partition table
[ 18.381481] sd 3:0:0:0: Attached scsi disk sdb
As you probably know this gives very very poor performance. Is there any way
to make it fast? I tried changing cables and reconnecting them but it looks
like it does not help. I can't do too much with this hardware since it is
used as production server. But testing some patches is of course possible. On
the other hand full kernel upgrade to 2.6.19 or .20 is not possible because
this kernel has openvz patches and I don't have them for .19 or .20 yet.
This is what I am getting from various utilities:
# dmesg
[ 0.000000] Linux version 2.6.18-028test010 (root@gamma) (gcc version
3.4.6 (Gentoo 3.4.6-r2, ssp-3.4.6-1.0, pie-8.7.10)) #3 SMP Thu Jan 18
02:02:53 CET 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fffb000 (usable)
[ 0.000000] BIOS-e820: 000000007fffb000 - 000000007ffff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007ffff000 - 0000000080000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 1151MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f0410
[ 0.000000] On node 0 totalpages: 524283
[ 0.000000] DMA zone: 4096 pages, LIFO batch:0
[ 0.000000] Normal zone: 225280 pages, LIFO batch:31
[ 0.000000] HighMem zone: 294907 pages, LIFO batch:31
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP (v000 ASUS ) @
0x000f5640
[ 0.000000] ACPI: RSDT (v001 ASUS TR-DLS 0x42302e31 MSFT 0x31313031) @
0x7fffb000
[ 0.000000] ACPI: FADT (v001 ASUS TR-DLS 0x42302e31 MSFT 0x31313031) @
0x7fffb0d8
[ 0.000000] ACPI: BOOT (v001 ASUS TR-DLS 0x42302e31 MSFT 0x31313031) @
0x7fffb030
[ 0.000000] ACPI: MADT (v001 ASUS TR-DLS 0x42302e31 MSFT 0x31313031) @
0x7fffb058
[ 0.000000] ACPI: DSDT (v001 ASUS TR-DLS 0x00001000 MSFT 0x0100000b) @
0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0xe408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x03] enabled)
[ 0.000000] Processor #3 6:11 APIC version 17
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:11 APIC version 17
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-15
[ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec01000] gsi_base[16])
[ 0.000000] IOAPIC[1]: apic_id 3 already used, trying 1
[ 0.000000] IOAPIC[1]: apic_id 1, version 17, address 0xfec01000, GSI
16-31
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec02000] gsi_base[32])
[ 0.000000] IOAPIC[2]: apic_id 4, version 17, address 0xfec02000, GSI
32-47
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 3 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap:
80000000:7ec00000)
[ 0.000000] Detected 1266.797 MHz processor.
[ 40.450209] Built 1 zonelists. Total pages: 524283
[ 40.450218] Kernel command line: BOOT_IMAGE=linux ro root=40
real_root=/dev/evms/root udev doevms2 no-hlt
[ 40.450629] mapped APIC to ffffd000 (fee00000)
[ 40.450636] mapped IOAPIC to ffffc000 (fec00000)
[ 40.450641] mapped IOAPIC to ffffb000 (fec01000)
[ 40.450647] mapped IOAPIC to ffffa000 (fec02000)
[ 40.450654] Enabling fast FPU save and restore... done.
[ 40.450660] Enabling unmasked SIMD FPU exception support... done.
[ 40.450667] Initializing CPU#0
[ 40.450745] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 40.452580] Console: colour VGA+ 80x25
[ 40.457081] Dentry cache hash table entries: 131072 (order: 7, 524288
bytes)
[ 40.459152] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 40.602726] Memory: 2069264k/2097132k available (3215k kernel code, 26736k
reserved, 921k data, 216k init, 1179628k highmem)
[ 40.602875] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[ 40.662614] Calibrating delay using timer specific routine.. 2533.95
BogoMIPS (lpj=1266979)
[ 40.664751] Mount-cache hash table entries: 512
[ 40.665157] CPU: After generic identify, caps: 0383fbff 00000000 00000000
00000000 00000000 00000000 00000000
[ 40.665180] CPU: After vendor identify, caps: 0383fbff 00000000 00000000
00000000 00000000 00000000 00000000
[ 40.665200] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 40.665310] CPU: L2 cache: 512K
[ 40.665382] CPU: After all inits, caps: 0383fbff 00000000 00000000
00000040 00000000 00000000 00000000
[ 40.665396] Intel machine check architecture supported.
[ 40.665477] Intel machine check reporting enabled on CPU#0.
[ 40.665592] Checking 'hlt' instruction... disabled
[ 40.665871] Freeing SMP alternatives: 20k freed
[ 40.665952] ACPI: Core revision 20060707
[ 40.670197] Page beancounter hash is 131072 entries.
[ 40.671587] CPU0: Intel(R) Pentium(R) III CPU family 1266MHz stepping
01
[ 40.671861] Booting processor 1/0 eip 2000
[ 40.682256] Initializing CPU#1
[ 40.742560] Calibrating delay using timer specific routine.. 2533.13
BogoMIPS (lpj=1266567)
[ 40.742574] CPU: After generic identify, caps: 0383fbff 00000000 00000000
00000000 00000000 00000000 00000000
[ 40.742587] CPU: After vendor identify, caps: 0383fbff 00000000 00000000
00000000 00000000 00000000 00000000
[ 40.742604] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 40.742609] CPU: L2 cache: 512K
[ 40.742614] CPU: After all inits, caps: 0383fbff 00000000 00000000
00000040 00000000 00000000 00000000
[ 40.742626] Intel machine check architecture supported.
[ 40.742633] Intel machine check reporting enabled on CPU#1.
[ 40.742978] CPU1: Intel(R) Pentium(R) III CPU - S 1266MHz stepping
04
[ 40.743597] Total of 2 processors activated (5067.09 BogoMIPS).
[ 40.744155] ENABLING IO-APIC IRQs
[ 40.744438] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 40.754527] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[ 40.754608] ...trying to set up timer (IRQ0) through the 8259A ... failed.
[ 40.754721] timer doesn't work through the IO-APIC - disabling NMI
Watchdog!
[ 40.754807] ...trying to set up timer as Virtual Wire IRQ... works.
[ 40.866487] checking TSC synchronization across 2 CPUs: passed.
[ 0.000955] Brought up 2 CPUs
[ 0.338431] migration_cost=1855
[ 0.338816] checking if image is initramfs... it is
[ 0.646592] Freeing initrd memory: 2292k freed
[ 0.647746] NET: Registered protocol family 16
[ 0.648073] ACPI: bus type pci registered
[ 0.648732] PCI: PCI BIOS revision 2.10 entry at 0xf1b10, last bus=1
[ 0.648825] PCI: Using configuration type 1
[ 0.648899] Setting up standard PCI resources
[ 0.657179] ACPI: Interpreter enabled
[ 0.657265] ACPI: Using IOAPIC for interrupt routing
[ 0.658504] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 14
15) *0, disabled.
[ 0.659394] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14
15) *0, disabled.
[ 0.660282] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14
15)
[ 0.661108] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14
15) *0, disabled.
[ 0.661995] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 *12 14
15)
[ 0.662841] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14
15) *0, disabled.
[ 0.663721] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14
15) *0, disabled.
[ 0.664616] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14
15) *0
[ 0.665455] ACPI: PCI Interrupt Link [LNKI] (IRQs 3 4 *5 6 7 9 10 11 12 14
15)
[ 0.666277] ACPI: PCI Interrupt Link [LNKJ] (IRQs 3 4 5 6 7 9 *10 11 12 14
15)
[ 0.667104] ACPI: PCI Interrupt Link [LNKK] (IRQs 3 4 5 6 7 9 10 11 12 14
15) *0, disabled.
[ 0.667987] ACPI: PCI Interrupt Link [LNKL] (IRQs 3 4 5tries: 1024 (order
0, 4096 bytes)
[ 0.776046] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
[ 0.776403] JFS: nTxBlock = 8192, nTxLock = 65536
[ 0.789371] SGI XFS with ACLs, security attributes, realtime, no debug
enabled
[ 0.790022] SGI XFS Quota Management subsystem
[ 0.790200] Initializing Cryptographic API
[ 0.790281] io scheduler noop registered
[ 0.790574] io scheduler cfq registered (default)
[ 0.791078] isapnp: Scanning for PnP cards...
[ 1.147170] isapnp: No Plug & Play device found
[ 1.190889] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing disabled
[ 1.191199] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.191472] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.192354] 00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.192760] 00:04: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.194261] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024
blocksize
[ 1.194595] netconsole: not configured, aborting
[ 1.194674] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 1.194760] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
[ 1.194943] SvrWks CSB5: IDE controller at PCI slot 0000:00:0f.1
[ 1.195044] SvrWks CSB5: chipset revision 147
[ 1.195120] SvrWks CSB5: not 100% native mode: will probe irqs later
[ 1.195321] ide0: BM-DMA at 0x7400-0x7407, BIOS settings: hda:pio,
hdb:pio
[ 1.195505] ide1: BM-DMA at 0x7408-0x740f, BIOS settings: hdc:pio,
hdd:pio
[ 1.195683] Probing IDE interface ide0...
[ 1.708783] Probing IDE interface ide1...
[ 2.221689] ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 23 (level, low)
-> IRQ 169
[ 2.367927] sym0: <1010-66> rev 0x1 at pci 0000:01:04.0 irq 169
[ 2.370131] sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
[ 2.370216] sym0: open drain IRQ line driver, using on-chip SRAM
[ 2.370298] sym0: using LOAD/STORE-based firmware.
[ 2.370377] sym0: handling phase mismatch from SCRIPTS.
[ 10.001807] sym1: SCSI BUS has been reset.
[ 10.001888] scsi1 : sym-2.2.3
[ 17.404451] libata version 2.00 loaded.
[ 17.404916] sata_uli 0000:00:04.0: version 1.0
[ 17.405009] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 18 (level, low)
-> IRQ 185
[ 17.405223] ata1: SATA max UDMA/133 cmd 0xD400 ctl 0xD002 bmdma 0xB000 irq
185
[ 17.405385] ata2: SATA max UDMA/133 cmd 0xB800 ctl 0xB402 bmdma 0xB008 irq
185
[ 17.405519] scsi2 : sata_uli
[ 17.858803] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 17.880541] ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ
(depth 0/32)
[ 17.880660] ata1.00: ata1: dev 0 multi count 16
[ 17.888858] ata1.00: configured for UDMA/133
[ 17.888941] scsi3 : sata_uli
[ 18.342469] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 18.343573] ata2.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ
(depth 0/32)
[ 18.343691] ata2.00: ata2: dev 0 multi count 16
[ 18.344972] ata2.00: configured for PIO4
[ 18.345466] Vendor: ATA Model: ST3250620NS Rev: 3.AE
[ 18.346391] Type: Direct-Access ANSI SCSI
revision: 05
[ 18.347464] Vendor: ATA Model: ST3250620NS Rev: 3.AE
[ 18.348390] Type: Direct-Access ANSI SCSI
revision: 05
[ 18.349457] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
[ 18.350234] sda: Write Protect is off
[ 18.350307] sda: Mode Sense: 00 3a 00 00
[ 18.351234] SCSI device sda: drive cache: write back
[ 18.352233] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
[ 18.352444] sda: Write Protect is off
[ 18.352517] sda: Mode Sense: 00 3a 00 00
[ 18.353443] SCSI device sda: drive cache: write back
[ 18.353522] sda: sda1 sda2
[ 18.371118] sd 2:0:0:0: Attached scsi disk sda
[ 18.372221] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
[ 18.372431] sdb: Write Protect is off
[ 18.372504] sdb: Mode Sense: 00 3a 00 00
[ 18.373440] SCSI device sdb: drive cache: write back
[ 18.374430] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
[ 18.375218] sdb: Write Protect is off
[ 18.375291] sdb: Mode Sense: 00 3a 00 00
[ 18.376216] SCSI device sdb: drive cache: write back
[ 18.376295] sdb: unknown partition table
[ 18.381481] sd 3:0:0:0: Attached scsi disk sdb
[ 18.381688] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 18.381774] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 18.383816] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 18.383956] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 18.384135] mice: PS/2 mouse device common for all mice
[ 18.384237] md: linear personality registered for level -1
[ 18.384317] md: raid0 personality registered for level 0
[ 18.384396] md: raid1 personality registered for level 1
[ 18.384479] md: raid10 personality registered for level 10
[ 18.401283] raid6: int32x1 410 MB/s
[ 18.418290] raid6: int32x2 515 MB/s
[ 18.435336] raid6: int32x4 363 MB/s
[ 18.452181] raid6: int32x8 339 MB/s
[ 18.469201] raid6: mmxx1 1218 MB/s
[ 18.486181] raid6: mmxx2 1468 MB/s
[ 18.503165] raid6: sse1x1 1144 MB/s
[ 18.520121] raid6: sse1x2 1472 MB/s
[ 18.520194] raid6: using algorithm sse1x2 (1472 MB/s)
[ 18.520275] md: raid6 personality registered for level 6
[ 18.520356] md: raid5 personality registered for level 5
[ 18.520436] md: raid4 personality registered for level 4
[ 18.520516] raid5: automatically using best checksumming function:
pIII_sse
[ 18.525116] pIII_sse : 2936.000 MB/sec
[ 18.525191] raid5: using function: pIII_sse (2936.000 MB/sec)
[ 18.525273] md: multipath personality registered for level -4
[ 18.525357] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 18.525440] md: bitmap version 4.39
[ 18.525761] device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
dm-devel@xxxxxxxxxx
[ 18.526030] device-mapper: multipath: version 1.0.4 loaded
[ 18.526117] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 18.526304] TCP bic registered
[ 18.526481] Starting balanced_irq
[ 18.526563] Using IPI Shortcut mode
[ 18.526865] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 18.527117] Time: tsc clocksource has been installed.
[ 18.527306] Freeing unused kernel memory: 216k freed
[ 18.575330] input: AT Translated Set 2 keyboard as /class/input/input0
[ 20.746542] ReiserFS: dm-4: found reiserfs format "3.6" with standard
journal
[ 20.951697] ReiserFS: dm-4: using ordered data mode
[ 20.962477] ReiserFS: dm-4: journal params: device dm-4, size 8192,
journal first block 18, max trans len 1024, max batch 900, max commit age 30,
max trans age 30
[ 20.964729] ReiserFS: dm-4: checking transaction log (dm-4)
[ 20.998074] ReiserFS: dm-4: Using r5 hash to sort names
[ 21.756494] NET: Registered protocol family 1
[ 24.535738] piix4_smbus 0000:00:0f.0: Found 0000:00:0f.0 device
[ 24.547532] e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
[ 24.547546] e100: Copyright(c) 1999-2005 Intel Corporation
[ 24.547642] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 20 (level, low)
-> IRQ 193
[ 24.571116] e100: eth0: e100_probe: addr 0xfe000000, irq 193, MAC addr
00:E0:18:59:69:9D
[ 27.230063] ReiserFS: dm-7: found reiserfs format "3.6" with standard
journal
[ 27.412980] ReiserFS: dm-7: using ordered data mode
[ 27.421903] ReiserFS: dm-7: journal params: device dm-7, size 8192,
journal first block 18, max trans len 1024, max batch 900, max commit age 30,
max trans age 30
[ 27.424180] ReiserFS: dm-7: checking transaction log (dm-7)
[ 27.452356] ReiserFS: dm-7: Using r5 hash to sort names
[ 27.479944] ReiserFS: dm-9: found reiserfs format "3.6" with standard
journal
[ 32.988256] ReiserFS: dm-9: using ordered data mode
[ 33.003544] ReiserFS: dm-9: journal params: device dm-9, size 8192,
journal first block 18, max trans len 1024, max batch 900, max commit age 30,
max trans age 30
[ 33.005611] ReiserFS: dm-9: checking transaction log (dm-9)
[ 33.053562] ReiserFS: dm-9: Using r5 hash to sort names
[ 33.127199] ReiserFS: dm-2: found reiserfs format "3.6" with standard
journal
[ 39.540725] ReiserFS: dm-2: using ordered data mode
[ 39.558141] ReiserFS: dm-2: journal params: device dm-2, size 8192,
journal first block 18, max trans len 1024, max batch 900, max commit age 30,
max trans age 30
[ 39.560283] ReiserFS: dm-2: checking transaction log (dm-2)
[ 39.611942] ReiserFS: dm-2: Using r5 hash to sort names
[ 41.866945] Adding 1048568k swap on /var/swapfile. Priority:-1
extents:211 across:1058640k
[ 178.626262] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 179.812674] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[ 180.962075] NET: Registered protocol family 17
[ 185.132332] NET: Unregistered protocol family 17
[ 185.141710] NET: Registered protocol family 17
# hdparm -vItT /dev/sda
/dev/sda:
IO_support = 0 (default 16-bit)
readonly = 0 (off)
readahead = 256 (on)
geometry = 30401/255/63, sectors = 488397168, start = 0
ATA device, with non-removable media
Model Number: ST3250620NS
Serial Number: 5QE08MGB
Firmware Revision: 3.AEE
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 488397168
device size with M = 1024*1024: 238475 MBytes
device size with M = 1000*1000: 250059 MBytes (250 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific
minimum
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 254, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
64-bit World wide name
unknown 84[11]
unknown 84[12]
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Phy event counters
Device-initiated interface power management
* Software settings preservation
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
Timing cached reads: 868 MB in 2.01 seconds = 432.39 MB/sec
Timing buffered disk reads: 198 MB in 3.03 seconds = 65.44 MB/sec
# hdparm -vItT /dev/sdb
/dev/sdb:
IO_support = 0 (default 16-bit)
readonly = 0 (off)
readahead = 256 (on)
geometry = 30401/255/63, sectors = 488397168, start = 0
ATA device, with non-removable media
Model Number: ST3250620NS
Serial Number: 9QF1Q5WE
Firmware Revision: 3.AEG
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 488397168
device size with M = 1024*1024: 238475 MBytes
device size with M = 1000*1000: 250059 MBytes (250 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific
minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0xfefe)
Recommended acoustic management value: 254, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
64-bit World wide name
unknown 84[11]
unknown 84[12]
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Phy event counters
Device-initiated interface power management
* Software settings preservation
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
Timing cached reads: 864 MB in 2.00 seconds = 431.88 MB/sec
Timing buffered disk reads: 14 MB in 3.34 seconds = 4.19 MB/sec
# smartctl -d ata -a /dev/sda
smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST3250620NS
Serial Number: 5QE08MGB
Firmware Version: 3.AEE
User Capacity: 250,059,350,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Feb 3 01:42:33 2007 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has
ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 106 089 006 Pre-fail Always -
11053265
3 Spin_Up_Time 0x0003 091 090 000 Pre-fail Always -
0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always -
16
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always -
0
7 Seek_Error_Rate 0x000f 080 060 030 Pre-fail Always -
110081628
9 Power_On_Hours 0x0032 100 100 000 Old_age Always -
479
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always -
0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always -
113
187 Unknown_Attribute 0x0032 100 100 000 Old_age Always -
0
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always -
0
190 Unknown_Attribute 0x0022 056 051 045 Old_age Always -
808189996
194 Temperature_Celsius 0x0022 044 049 000 Old_age Always -
44 (Lifetime Min/Max 0/29)
195 Hardware_ECC_Recovered 0x001a 063 058 000 Old_age Always -
6
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always -
0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline -
0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always -
0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline -
0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always -
0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Extended offline Completed without error 00% 478 -
# 2 Extended offline Interrupted (host reset) 80% 473 -
# 3 Short offline Completed without error 00% 473 -
# 4 Extended offline Completed without error 00% 393 -
# 5 Short offline Completed without error 00% 391 -
# 6 Extended offline Completed without error 00% 15 -
# 7 Short offline Completed without error 00% 14 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
# smartctl -d ata -a /dev/sdb
smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST3250620NS
Serial Number: 9QF1Q5WE
Firmware Version: 3.AEG
User Capacity: 250,059,350,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Feb 3 01:43:04 2007 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has
ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 112 100 006 Pre-fail Always -
49974568
3 Spin_Up_Time 0x0003 096 095 000 Pre-fail Always -
0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always -
6
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always -
0
7 Seek_Error_Rate 0x000f 063 060 030 Pre-fail Always -
2188910
9 Power_On_Hours 0x0032 100 100 000 Old_age Always -
24
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always -
0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always -
22
187 Unknown_Attribute 0x0032 100 100 000 Old_age Always -
0
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always -
0
190 Unknown_Attribute 0x0022 056 051 045 Old_age Always -
757858348
194 Temperature_Celsius 0x0022 044 049 000 Old_age Always -
44 (Lifetime Min/Max 0/33)
195 Hardware_ECC_Recovered 0x001a 073 071 000 Old_age Always -
193550671
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always -
0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline -
0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always -
0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline -
0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always -
0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Extended offline Completed without error 00% 4 -
# 2 Extended offline Interrupted (host reset) 60% 2 -
# 3 Short offline Completed without error 00% 1 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
More info available on request.
Any ideas?
Thanks in advance,
Grzegorz Kulewski
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
