Andrew Morton wrote: > On Fri, 15 Dec 2006 15:45:55 +0059 > Jiri Slaby <jirislaby@xxxxxxxxx> wrote: > >> Andrew Morton wrote: >>> Temporarily at >>> >>> http://userweb.kernel.org/~akpm/2.6.20-rc1-mm1/ >>> >>> Will appear later at >>> >>> ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.20-rc1/2.6.20-rc1-mm1/ >> The kernel panics at boot in pdc_port_start+0x82 with deref of 0x14: >> http://www.fi.muni.cz/~xslaby/sklad/pdc_oops.png >> >> ATA port is not connected, only 2 SATA disks on my >> # lspci -vvxs 02:01.0 >> 02:01.0 Mass storage controller: Promise Technology, Inc. PDC40775 (SATA 300 >> TX2plus) (rev 02) >> Subsystem: Promise Technology, Inc. PDC40775 (SATA 300 TX2plus) >> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- >> Stepping- SERR- FastB2B- >> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- >> Latency: 72 (1000ns min, 4500ns max), Cache Line Size: 4 bytes >> Interrupt: pin A routed to IRQ 19 >> Region 0: I/O ports at 8000 [size=128] >> Region 2: I/O ports at 8400 [size=256] >> Region 3: Memory at fb025000 (32-bit, non-prefetchable) [size=4K] >> Region 4: Memory at fb000000 (32-bit, non-prefetchable) [size=128K] >> [virtual] Expansion ROM at 50000000 [disabled] [size=32K] >> Capabilities: [60] Power Management version 2 >> Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA >> PME(D0-,D1-,D2-,D3hot-,D3cold-) >> Status: D0 PME-Enable- DSel=0 DScale=0 PME- >> 00: 5a 10 73 3d 07 00 30 02 02 00 80 01 01 48 00 00 >> 10: 01 80 00 00 00 00 00 00 01 84 00 00 00 50 02 fb >> 20: 00 00 00 fb 00 00 00 00 00 00 00 00 5a 10 73 3d >> 30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 04 12 >> > > Presumably > > void __iomem *mmio = (void __iomem *) ap->ioaddr.scr_addr; > > gave us a null pointer. > > Something like this: > > diff -puN drivers/ata/sata_promise.c~a drivers/ata/sata_promise.c > --- a/drivers/ata/sata_promise.c~a > +++ a/drivers/ata/sata_promise.c > @@ -294,6 +294,10 @@ static int pdc_port_start(struct ata_por > void __iomem *mmio = (void __iomem *) ap->ioaddr.scr_addr; > unsigned int tmp; > > + if (!mmio) { > + rc = -EDOM; > + goto out_kfree; > + } > tmp = readl(mmio + 0x014); > tmp = (tmp & ~3) | 1; /* set bits 1:0 = 0:1 */ > writel(tmp, mmio + 0x014); > _ > > should perhaps let you wobble to a state where you can get us the full > dmesg output, please. > > Actually, that should already be possible simply using netconsole. I set it up and here it comes: [ 6.779351] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 21 (level, low) -> IRQ 19 [ 6.779483] sata_promise PATA port found [ 6.779584] ata3: SATA max UDMA/133 cmd 0xF8816200 ctl 0xF8816238 bmdma 0x0 irq 19 [ 6.779708] ata4: SATA max UDMA/133 cmd 0xF8816280 ctl 0xF88162B8 bmdma 0x0 irq 19 [ 6.779831] BUG: unable to handle kernel NULL pointer dereference at virtual address 00000014 [ 6.779958] printing eip: [ 6.780020] c02753b9 [ 6.780080] *pde = 00000000 [ 6.780142] Oops: 0000 [#1] [ 6.780202] SMP [ 6.780328] last sysfs file: [ 6.780389] Modules linked in: [ 6.780488] CPU: 1 [ 6.780488] EIP: 0060:[<c02753b9>] Not tainted VLI [ 6.780490] EFLAGS: 00010202 (2.6.20-rc1-mm1 #203) [ 6.780680] EIP is at pdc_port_start+0x82/0xb0 [ 6.780742] eax: 00000001 ebx: f7e3d9a0 ecx: 00000000 edx: 00000000 [ 6.780808] esi: f7dcc2e8 edi: 00000000 ebp: c193fe3c esp: c193fe24 [ 6.780873] ds: 007b es: 007b fs: 00d8 gs: 0000 ss: 0068 [ 6.780938] Process swapper (pid: 1, ti=c193e000 task=c1923a90 task.ti=c193e000) [ 6.781004] Stack: 000000d0 c1a59a80 c1adcc48 f7ea4000 f88162b8 f7dcc2e8 c193fe90 c026c724 [ 6.781398] 00000078 00000004 00000053 c043d998 f8816280 f88162b8 00000000 00000013 [ 6.781789] f7ea4000 f7d91b00 f8816280 c1adcc48 00000013 c1adcc00 00000002 c01de64f [ 6.782180] Call Trace: [ 6.782298] [<c0103f1b>] show_trace_log_lvl+0x1a/0x30 [ 6.782396] [<c0103fd6>] show_stack_log_lvl+0xa5/0xca [ 6.782494] [<c01041ce>] show_registers+0x1d3/0x2b8 [ 6.782591] [<c01043d4>] die+0x121/0x243 [ 6.782690] [<c01193b0>] do_page_fault+0x2b8/0x5e8 [ 6.782788] [<c0389e74>] error_code+0x7c/0x84 [ 6.782885] [<c026c724>] ata_device_add+0x1b1/0x516 [ 6.782983] [<c027568e>] pdc_ata_init_one+0x2a7/0x3e9 [ 6.783081] [<c01e057e>] pci_device_probe+0x44/0x5f [ 6.783180] [<c02432a2>] driver_probe_device+0x75/0x12c [ 6.783279] [<c0243470>] __driver_attach+0x8c/0x8e [ 6.783376] [<c02428b3>] bus_for_each_dev+0x44/0x62 [ 6.783476] [<c0243161>] driver_attach+0x19/0x1b [ 6.783574] [<c0242ba7>] bus_add_driver+0x6a/0x188 [ 6.783671] [<c02436c9>] driver_register+0x54/0x84 [ 6.783768] [<c01e06e0>] __pci_register_driver+0x45/0x73 [ 6.783865] [<c0520f34>] pdc_ata_init+0xf/0x1b [ 6.783967] [<c01004b6>] init+0x10d/0x310 [ 6.784063] [<c0103bbf>] kernel_thread_helper+0x7/0x18 [ 6.784160] ======================= [ 6.784224] Code: 00 8b 45 f0 e8 ca 25 e9 ff 89 03 85 c0 74 32 89 9e 54 20 00 00 8b 45 ec f6 00 01 74 b6 89 f0 e8 99 1b ff ff 85 c0 74 ab 8b 56 64 <8b> 42 14 83 e0 fc 83 c8 01 89 42 14 89 f8 83 c4 0c 5b 5e 5f 5d [ 6.786508] EIP: [<c02753b9>] pdc_port_start+0x82/0xb0 SS:ESP 0068:c193fe24 [ 6.786641] <0>Kernel panic - not syncing: Attempted to kill init! [ 6.787970] regards, -- http://www.fi.muni.cz/~xslaby/ Jiri Slaby faculty of informatics, masaryk university, brno, cz e-mail: jirislaby gmail com, gpg pubkey fingerprint: B674 9967 0407 CE62 ACC8 22A0 32CC 55C3 39D4 7A7E - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
