On Mon, 2006-12-04 at 21:41 -0800, Andrew Morton wrote:
> On Mon, 04 Dec 2006 23:56:42 -0500
> Jeff Garzik <jeff@xxxxxxxxxx> wrote:
>
> > Andrew Morton wrote:
> > > via-pata-controller-xfer-fixes.patch
> > > via-pata-controller-xfer-fixes-fix.patch
> >
> > Tejun's 3d3cca37559e3ab2b574eda11ed5207ccdb8980a has been ack'd by the
> > reporter as fixing things, so these two shouldn't be needed.
>
> OK thanks, I dropped it.
>
> >
> > > libata_resume_fix.patch
> >
> > I thought this was resolved long ago? Are there still open reports that
> > this solves, where upstream doesn't work?
>
> Heck, I don't know.
>
> >
> > > ahci-ati-sb600-sata-support-for-various-modes.patch
> >
> > With the PCI quirk, I thought ATI was finally sorted?
>
> Was it? I don't know that either.
>
> I'll drop these too.
> -
Hi Jeff, Andrew
The following patch is ATI's final solution. It was ACKed by Alan.
Jeff, you're the maintainer of libata, but this patch is based on
pci/quirks.c, so I don't know who will apply this patch? You or somebody
else?
Andrew, could you please drop ATI's previous patch and add this one
in next -mm patch? The previous patch I sent
(ahci-ati-sb600-sata-support-for-various-modes.patch) is not as good as
this one :)
Best regards,
Conke @AMD/ATI
[------------------PATCH------------------]
--- linux-2.6.19-rc6-git4/drivers/pci/quirks.c.orig 2006-11-23
19:45:49.000000000 +0800
+++ linux-2.6.19-rc6-git4/drivers/pci/quirks.c 2006-11-23
19:34:23.000000000 +0800
@@ -795,6 +795,25 @@ static void __init quirk_mediagx_master(
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX,
PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master );
+
+#if defined(CONFIG_SATA_AHCI) || defined(CONFIG_SATA_AHCI_MODULE)
+static void __devinit quirk_sb600_sata(struct pci_dev *pdev)
+{
+ /* set sb600 sata to ahci mode */
+ if ((pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
+ u8 tmp;
+
+ pci_read_config_byte(pdev, 0x40, &tmp);
+ pci_write_config_byte(pdev, 0x40, tmp|1);
+ pci_write_config_byte(pdev, 0x9, 1);
+ pci_write_config_byte(pdev, 0xa, 6);
+ pci_write_config_byte(pdev, 0x40, tmp);
+
+ pdev->class = 0x010601;
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI,
PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_sb600_sata);
+#endif
/*
* As per PCI spec, ignore base address registers 0-3 of the IDE
controllers
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
