Hello,
After upgrading to 2.6.19-rc6 and enabling experimental support of
pata_via noticed that my hdd was downgraded to UDMA/33:
Before (2.6.18-rc & via82cxxx):
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override withidebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
PCI: VIA IRQ fixup for 0000:00:07.1, from 255 to 0
VP_IDE: chipset revision 16
VP_IDE: not 100%% native mode: will probe irqs later
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci0000:00:07.1
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hda: max request size: 128KiB
hda: 40031712 sectors (20496 MB) w/512KiB Cache, CHS=39714/16/63, UDMA(66)
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 >
Now (2.6.16-rc6 & pata_via):
pata_via 0000:00:07.1: version 0.1.14
ata1: PATA max UDMA/66 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14
ata2: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xFFA8 irq 15
scsi0 : pata_via
ata1.00: ATA-5, max UDMA/66, 40031712 sectors: LBA
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/33
scsi1 : pata_via
ata2: port is slow to respond, please be patient (Status 0xff)
ata2: port failed to respond (30 secs, Status 0xff)
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: softreset failed, retrying in 5 secs
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: softreset failed, retrying in 5 secs
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: reset failed, giving up
scsi 0:0:0:0: Direct-Access ATA FUJITSU MPF3204A 0031 PQ: 0 ANSI: 5
SCSI device sda: 40031712 512-byte hdwr sectors (20496 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 40031712 512-byte hdwr sectors (20496 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 >
sd 0:0:0:0: Attached scsi disk sda
# hdparm -I /dev/sda|grep dma
DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
BTW: is it possible to do something with this annoying long delay with
the "port is slow to respond, please be patient" message? :)
Best regards,
Krzysztof Olędzki
