Re: [PATCH] libata: skip reset on bus not a device

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Oct 09, 2006 at 04:00:33PM +0900, Tejun Heo wrote:
> Joe Jin wrote:
> >>SRST failure would have still occurred but 30sec timeout should have
> >>gone.  Can you post full dmesg?
> >
> >Yes it is.
> >attachment is the output of dmesg
> 
> Great.
> 
> >>Also, please test the patch in the following mail.  You can use either
> >>git or download the full kernel tarball to get the modified kernel.
> >>
> >
> >Did the pathc against 2.6.19-rc1?
> >I have test it, but it have not any change and timeout also appeared :(
> 
> It's against libata development tree.  So, you downloaded the tar.gz and 
> tested it?

And, one more thing to try.  The following patch should fix your
problem.  It's against v2.6.18.

diff --git a/drivers/scsi/libata-core.c b/drivers/scsi/libata-core.c
index 427b73a..3bc7f57 100644
--- a/drivers/scsi/libata-core.c
+++ b/drivers/scsi/libata-core.c
@@ -2271,11 +2271,14 @@ static inline void ata_tf_to_host(struct
  *	Sleep until ATA Status register bit BSY clears,
  *	or a timeout occurs.
  *
- *	LOCKING: None.
+ *	LOCKING:
+ *	Kernel thread context (may sleep).
+ *
+ *	RETURNS:
+ *	0 on success, -errno otherwise.
  */
-
-unsigned int ata_busy_sleep (struct ata_port *ap,
-			     unsigned long tmout_pat, unsigned long tmout)
+int ata_busy_sleep(struct ata_port *ap,
+		   unsigned long tmout_pat, unsigned long tmout)
 {
 	unsigned long timer_start, timeout;
 	u8 status;
@@ -2283,25 +2286,30 @@ unsigned int ata_busy_sleep (struct ata_
 	status = ata_busy_wait(ap, ATA_BUSY, 300);
 	timer_start = jiffies;
 	timeout = timer_start + tmout_pat;
-	while ((status & ATA_BUSY) && (time_before(jiffies, timeout))) {
+	while (status != 0xff && (status & ATA_BUSY) &&
+	       time_before(jiffies, timeout)) {
 		msleep(50);
 		status = ata_busy_wait(ap, ATA_BUSY, 3);
 	}
 
-	if (status & ATA_BUSY)
+	if (status != 0xff && (status & ATA_BUSY))
 		ata_port_printk(ap, KERN_WARNING,
 				"port is slow to respond, please be patient\n");
 
 	timeout = timer_start + tmout;
-	while ((status & ATA_BUSY) && (time_before(jiffies, timeout))) {
+	while (status != 0xff && (status & ATA_BUSY) &&
+	       time_before(jiffies, timeout)) {
 		msleep(50);
 		status = ata_chk_status(ap);
 	}
 
+	if (status == 0xff)
+		return -ENODEV;
+
 	if (status & ATA_BUSY) {
 		ata_port_printk(ap, KERN_ERR, "port failed to respond "
 				"(%lu secs)\n", tmout / HZ);
-		return 1;
+		return -EBUSY;
 	}
 
 	return 0;
@@ -2392,10 +2400,8 @@ static unsigned int ata_bus_softreset(st
 	 * the bus shows 0xFF because the odd clown forgets the D7
 	 * pulldown resistor.
 	 */
-	if (ata_check_status(ap) == 0xFF) {
-		ata_port_printk(ap, KERN_ERR, "SRST failed (status 0xFF)\n");
-		return AC_ERR_OTHER;
-	}
+	if (ata_check_status(ap) == 0xFF)
+		return 0;
 
 	ata_bus_post_reset(ap, devmask);
 
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 66c3100..eb7d90f 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -702,9 +702,8 @@ extern int ata_host_set_suspend(struct a
 				pm_message_t mesg);
 extern void ata_host_set_resume(struct ata_host_set *host_set);
 extern int ata_ratelimit(void);
-extern unsigned int ata_busy_sleep(struct ata_port *ap,
-				   unsigned long timeout_pat,
-				   unsigned long timeout);
+extern int ata_busy_sleep(struct ata_port *ap,
+			  unsigned long timeout_pat, unsigned long timeout);
 extern void ata_port_queue_task(struct ata_port *ap, void (*fn)(void *),
 				void *data, unsigned long delay);
 extern u32 ata_wait_register(void __iomem *reg, u32 mask, u32 val,
@@ -1019,7 +1018,7 @@ static inline u8 ata_busy_wait(struct at
 		udelay(10);
 		status = ata_chk_status(ap);
 		max--;
-	} while ((status & bits) && (max > 0));
+	} while (status != 0xff && (status & bits) && (max > 0));
 
 	return status;
 }
@@ -1040,7 +1039,7 @@ static inline u8 ata_wait_idle(struct at
 {
 	u8 status = ata_busy_wait(ap, ATA_BUSY | ATA_DRQ, 1000);
 
-	if (status & (ATA_BUSY | ATA_DRQ)) {
+	if (status != 0xff && (status & (ATA_BUSY | ATA_DRQ))) {
 		unsigned long l = ap->ioaddr.status_addr;
 		if (ata_msg_warn(ap))
 			printk(KERN_WARNING "ATA: abnormal status 0x%X on port 0x%lX\n",

-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux