Hi All,
Here is v8 of my patch series to move the manual instantation of lis3lv02d
i2c_client-s for SMO88xx ACPI device from the generic i2c-i801.c code to
a SMO88xx specific dell-lis3lv02d driver.
Moving the i2c_client instantiation there has the following advantages:
1. This moves the SMO88xx ACPI device quirk handling away from the generic
i2c-i801 module which is loaded on all Intel x86 machines to a module
which will only be loaded when there is an ACPI SMO88xx device.
2. This removes the duplication of the SMO88xx ACPI Hardware ID (HID) table
between the i2c-i801 and dell-smo8800 drivers.
3. This allows extending the quirk handling by adding new code and related
module parameters to the dell-lis3lv02d driver, without needing to modify
the i2c-i801 code.
This series also extends the i2c_client instantiation with support for
probing for the i2c-address of the lis3lv02d chip on devices which
are not yet listed in the DMI table with i2c-addresses for known models.
This probing is only done when requested through a module parameter.
Changes in v8:
- Address some minor review remarks from Andy
Changes in v7:
- Rebase on v6.11-rc1
Changes in v6:
- Use i2c_new_scanned_device() instead of re-inventing it
Changes in v5:
- Make match_acpi_device_ids() and match_acpi_device_ids[] __init[const]
- Add "Depends on I2C" to Kconfig (to fix kernel-test-robot reported issues)
- Add "this may be dangerous warning" to MODULE_PARM_DESC(probe_i2c_addr)
Changes in v4:
- Move the i2c_client instantiation to a new dell-lis3lv02d driver instead
of adding it to the dell-smo8800 driver
- Address a couple of other minor review comments
Changes in v3:
- Use an i2c bus notifier so that the i2c_client will still be instantiated if
the i801 i2c_adapter shows up later or is re-probed (removed + added again).
This addresses the main concern / review-comments made during review of v2.
- Add 2 prep patches to the i2c-core / the i2c-i801 driver to allow bus-notifier
use / to avoid the need to duplicate the PCI-ids of IDF i2c-i801 adapters.
- Switch to standard dmi_system_id matching to check both sys-vendor +
product-name DMI fields
- Drop the patch to alternatively use the st_accel IIO driver instead of
drivers/misc/lis3lv02d/lis3lv02d.c
Changes in v2:
- Drop "[PATCH 1/6] platform/x86: dell-smo8800: Only load on Dell laptops"
- Use a pci_device_id table to check for IDF (non main) i2c-i801 SMBusses
- Add a comment documenting the IDF PCI device ids
- Keep using drivers/misc/lis3lv02d/lis3lv02d.c by default
- Rename the module-parameter to use_iio_driver which can be set to
use the IIO st_accel driver instead
- Add a new patch adding the accelerometer address for the 2 models
I have tested this on to dell_lis3lv02d_devices[]
Since this touches files under both drivers/i2c and drivers/platform/x86
some subsystem coordination is necessary. I think it would be best to just
merge the entire series through the i2c subsystem since this touches some
core i2c files. As pdx86 subsys co-maintainer I'm fine with doing so.
Regards,
Hans
Hans de Goede (6):
i2c: core: Setup i2c_adapter runtime-pm before calling device_add()
i2c: i801: Use a different adapter-name for IDF adapters
platform/x86: dell-smo8800: Move SMO88xx acpi_device_ids to
dell-smo8800-ids.h
platform/x86: dell-smo8800: Move instantiation of lis3lv02d i2c_client
from i2c-i801 to dell-lis3lv02d
platform/x86: dell-smo8800: Add a couple more models to
lis3lv02d_devices[]
platform/x86: dell-smo8800: Add support for probing for the
accelerometer i2c address
drivers/i2c/busses/i2c-i801.c | 133 +---------
drivers/i2c/i2c-core-base.c | 18 +-
drivers/platform/x86/dell/Kconfig | 1 +
drivers/platform/x86/dell/Makefile | 1 +
drivers/platform/x86/dell/dell-lis3lv02d.c | 252 +++++++++++++++++++
drivers/platform/x86/dell/dell-smo8800-ids.h | 27 ++
drivers/platform/x86/dell/dell-smo8800.c | 16 +-
7 files changed, 302 insertions(+), 146 deletions(-)
create mode 100644 drivers/platform/x86/dell/dell-lis3lv02d.c
create mode 100644 drivers/platform/x86/dell/dell-smo8800-ids.h
--
2.46.0
