On 30/11/2023 05:44, Andrew Jeffery wrote:
On Wed, 2023-11-29 at 16:02 +0700, Quan Nguyen wrote:
On 29/11/2023 07:33, Andrew Jeffery wrote:
On Tue, 2023-11-28 at 14:52 +0700, Quan Nguyen wrote:
diff --git a/drivers/i2c/busses/i2c-aspeed.c b/drivers/i2c/busses/i2c-aspeed.c
index 79476b46285b..3231f430e335 100644
--- a/drivers/i2c/busses/i2c-aspeed.c
+++ b/drivers/i2c/busses/i2c-aspeed.c
@@ -611,8 +611,9 @@ static irqreturn_t aspeed_i2c_bus_irq(int irq, void *dev_id)
spin_lock(&bus->lock);
irq_received = readl(bus->base + ASPEED_I2C_INTR_STS_REG);
- /* Ack all interrupts except for Rx done */
- writel(irq_received & ~ASPEED_I2CD_INTR_RX_DONE,
+ /* Ack all interrupts except for Rx done and Tx done with/without ACK */
I'm not a huge fan of this comment, it just says what the code does. It
would be much better to explain *why* the code does what it does.
I realise describing what the code does was already the gist of the
comment and that you're just updating it to match the change to the
code, but that's my entire problem with it. We'd be better off deleting
it if we're not going to explain why the masking is necessary.
Thanks for the comment Andrew.
I would prefer to delete it.
But if to put some comment, how about:
/* Early ack INTR_RX_DONE, INTR_TX_[ACK|NAK] would indicate HW to start
receiving/sending new data and may cause a race condition as irq handler
not yet to handle these irqs but being acked. Let ack them late in the
end of irq handler when those are truly processed */
Please update the patch with this comment. It at least goes some way to
explain why.
Yes, will do in next version.
+ writel(irq_received &
+ ~(ASPEED_I2CD_INTR_RX_DONE | ASPEED_I2CD_INTR_TX_ACK | ASPEED_I2CD_INTR_TX_NAK),
bus->base + ASPEED_I2C_INTR_STS_REG);
readl(bus->base + ASPEED_I2C_INTR_STS_REG);
irq_received &= ASPEED_I2CD_INTR_RECV_MASK;
@@ -657,12 +658,12 @@ static irqreturn_t aspeed_i2c_bus_irq(int irq, void *dev_id)
"irq handled != irq. expected 0x%08x, but was 0x%08x\n",
irq_received, irq_handled);
- /* Ack Rx done */
- if (irq_received & ASPEED_I2CD_INTR_RX_DONE) {
- writel(ASPEED_I2CD_INTR_RX_DONE,
- bus->base + ASPEED_I2C_INTR_STS_REG);
- readl(bus->base + ASPEED_I2C_INTR_STS_REG);
- }
+ /* Ack Rx done and Tx done with/without ACK */
+ writel(irq_received &
+ (ASPEED_I2CD_INTR_RX_DONE | ASPEED_I2CD_INTR_TX_ACK | ASPEED_I2CD_INTR_TX_NAK),
+ bus->base + ASPEED_I2C_INTR_STS_REG);
+ readl(bus->base + ASPEED_I2C_INTR_STS_REG);
I'm not sure why the write was conditional, but I'm not sure that
making it unconditional is valid either? Why the change? Why not add
the extra interrupt bits to the condition in addition to the value mask
for the write?
In original code, only INTR_RX_DONE was acked late. So the check
(irq_received & ASPEED_I2CD_INTR_RX_DONE) is need and that help to save
one write() then read() if there was no such irq.
In the new code, there is no such check and the drawback is that there
always be one write() and one read() for all cases, include the case
where there is no irq at all, ie writing 0 into ASPEED_I2C_INTR_STS_REG.
And yes, your concern maybe right, we can not say of writing 0 into
ASPEED_I2C_INTR_STS_REG is good or not.
I checked back my debug log and seeing that irq always come with at
least one of INTR_RX_DONE BIT(2), INTR_TX_ACK BIT(0), INTR_TX_NAK BIT(1)
raised. So it seems like the case of writing 0 into
ASPEED_I2C_INTR_STS_REG is indeed rarely to happen.
Do you think we should change it to:
if (irq_received & (INTR_RX_DONE | INTR_TX_ACK | INTR_TX_NAK)) {
writel( irq_received & (INTR_RX_DONE| INTR_TX_ACK| INTR_TX_NAK),
bus->base + ASPEED_I2C_INTR_STS_REG);
readl(bus->base + ASPEED_I2C_INTR_STS_REG);
}
This is less different from the existing strategy and doesn't require
any explanation beyond what you're already trying to achieve in the
patch, so I think you should switch to this approach.
If someone wants to work out why it was done conditionally and argue
for its removal then they can do that separately.
I agree, will update in next version.
Thanks
- Quan
