From: Yann Sionneau <ysionneau@xxxxxxxxx>
The designware IP can be synthesized with the IC_EMPTYFIFO_HOLD_MASTER_EN
parameter.
In which case, if the TX FIFO gets empty and the last command didn't have
the STOP bit (IC_DATA_CMD[9]), the dw_apb_i2c will hold SCL low until
a new command is pushed into the TX FIFO or the transfer is aborted.
When the dw_apb_i2c is holding SCL low, it cannot be disabled.
The transfer must first be aborted.
Also, the bus recover won't work because SCL is held low by the master.
This patch checks if the master is holding SCL low in __i2c_dw_disable
before trying to disable the IP.
If SCL is held low, an abort is initiated.
When the abort is done, the disabling can then proceed.
This whole situation can happen for instance during SMBUS read data block
if the slave just responds with "byte count == 0".
This puts the master in an unrecoverable state, holding SCL low and the
current __i2c_dw_disable procedure is not working. In this situation
only a Linux reboot can fix the i2c bus.
Co-developed-by: Jonathan Borne <jborne@xxxxxxxxx>
Signed-off-by: Jonathan Borne <jborne@xxxxxxxxx>
Tested-by: Yann Sionneau <ysionneau@xxxxxxxxx>
Signed-off-by: Yann Sionneau <ysionneau@xxxxxxxxx>
---
drivers/i2c/busses/i2c-designware-common.c | 17 +++++++++++++++++
drivers/i2c/busses/i2c-designware-core.h | 3 +++
2 files changed, 20 insertions(+)
diff --git a/drivers/i2c/busses/i2c-designware-common.c b/drivers/i2c/busses/i2c-designware-common.c
index 9f8574320eb2..744927b0c5af 100644
--- a/drivers/i2c/busses/i2c-designware-common.c
+++ b/drivers/i2c/busses/i2c-designware-common.c
@@ -440,8 +440,25 @@ void __i2c_dw_disable(struct dw_i2c_dev *dev)
{
int timeout = 100;
u32 status;
+ u32 raw_intr_stats;
+ u32 enable;
+ bool abort_needed;
+ bool abort_done = false;
+
+ regmap_read(dev->map, DW_IC_RAW_INTR_STAT, &raw_intr_stats);
+ regmap_read(dev->map, DW_IC_ENABLE, &enable);
+
+ abort_needed = raw_intr_stats & DW_IC_INTR_MST_ON_HOLD;
+ if (abort_needed)
+ regmap_write(dev->map, DW_IC_ENABLE, enable | DW_IC_ENABLE_ABORT);
do {
+ if (abort_needed && !abort_done) {
+ regmap_read(dev->map, DW_IC_ENABLE, &enable);
+ abort_done = !(enable & DW_IC_ENABLE_ABORT);
+ continue;
+ }
+
__i2c_dw_disable_nowait(dev);
/*
* The enable status register may be unimplemented, but
diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h
index 19ae23575945..dcd9bd9ee00f 100644
--- a/drivers/i2c/busses/i2c-designware-core.h
+++ b/drivers/i2c/busses/i2c-designware-core.h
@@ -98,6 +98,7 @@
#define DW_IC_INTR_START_DET BIT(10)
#define DW_IC_INTR_GEN_CALL BIT(11)
#define DW_IC_INTR_RESTART_DET BIT(12)
+#define DW_IC_INTR_MST_ON_HOLD BIT(13)
#define DW_IC_INTR_DEFAULT_MASK (DW_IC_INTR_RX_FULL | \
DW_IC_INTR_TX_ABRT | \
@@ -109,6 +110,8 @@
DW_IC_INTR_RX_UNDER | \
DW_IC_INTR_RD_REQ)
+#define DW_IC_ENABLE_ABORT BIT(1)
+
#define DW_IC_STATUS_ACTIVITY BIT(0)
#define DW_IC_STATUS_TFE BIT(2)
#define DW_IC_STATUS_MASTER_ACTIVITY BIT(5)
--
2.17.1
