On 17/01/2023 10:44, Delphine CC Chiu wrote:
> Add support for meta control-logic-device driver. The CLD manages the
> server system power squence and other state such as host-power-state,
> uart-selection and presense-slots. The baseboard management controller
> (BMC) can access the CLD through I2C.
>
> The version 1 of CLD driver is supported. The registers number, name
> and mode of CLD can be defined in dts file for version 1. The driver
> exports the filesystem following the dts setting.
>
> Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@xxxxxxxxxx>
> Tested-by: Bonnie Lo <Bonnie_Lo@xxxxxxxxxx>
> ---
> MAINTAINERS | 6 +
> drivers/misc/Kconfig | 9 +
> drivers/misc/Makefile | 1 +
> drivers/misc/control-logic-device.c | 443 ++++++++++++++++++++++++++++
> 4 files changed, 459 insertions(+)
> create mode 100644 drivers/misc/control-logic-device.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 7483853880b6..46e250a2c334 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -13388,6 +13388,12 @@ T: git git://linuxtv.org/media_tree.git
> F: Documentation/devicetree/bindings/media/amlogic,gx-vdec.yaml
> F: drivers/staging/media/meson/vdec/
>
> +META CPLD DRIVER
> +M: Delphine CC Chiu <Delphine_CC_Chiu@xxxxxxxxxx>
> +L: linux-i2c@xxxxxxxxxxxxxxx
> +S: Maintained
> +F: Documentation/devicetree/bindings/misc/meta,control-logic-device.txt
Missing entries for driver code.
> +
> METHODE UDPU SUPPORT
> M: Vladimir Vid <vladimir.vid@xxxxxxxxxx>
> S: Maintained
> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
> index 358ad56f6524..21d3bf820438 100644
> --- a/drivers/misc/Kconfig
> +++ b/drivers/misc/Kconfig
> @@ -496,6 +496,15 @@ config VCPU_STALL_DETECTOR
>
> If you do not intend to run this kernel as a guest, say N.
>
> +config CONTROL_LOGIC_DEVICE
> + bool "Meta Control Logic Device Driver"
Too generic...
> + depends on I2C && REGMAP
> + help
> + Say yes here to add support for the Meta CLD device driver. The dirver
> + is used to monitor CLD register value and notify the application if
> + value is changed. Application also can access the CLD register value
> + through this driver.
> +
> source "drivers/misc/c2port/Kconfig"
> source "drivers/misc/eeprom/Kconfig"
> source "drivers/misc/cb710/Kconfig"
> diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
> index ac9b3e757ba1..6fcdd575a143 100644
> --- a/drivers/misc/Makefile
> +++ b/drivers/misc/Makefile
> @@ -62,3 +62,4 @@ obj-$(CONFIG_HI6421V600_IRQ) += hi6421v600-irq.o
> obj-$(CONFIG_OPEN_DICE) += open-dice.o
> obj-$(CONFIG_GP_PCI1XXXX) += mchp_pci1xxxx/
> obj-$(CONFIG_VCPU_STALL_DETECTOR) += vcpu_stall_detector.o
> +obj-$(CONFIG_CONTROL_LOGIC_DEVICE) += control-logic-device.o
Does not look like ordered by name.
> diff --git a/drivers/misc/control-logic-device.c b/drivers/misc/control-logic-device.c
> new file mode 100644
> index 000000000000..07113dcb0836
> --- /dev/null
> +++ b/drivers/misc/control-logic-device.c
> @@ -0,0 +1,443 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2022 Meta Inc.
> + */
> +
> + #include <linux/module.h>
Don't prepend with spaces. Check the code for such trivial style issues
first.
> +#include <linux/i2c.h>
> +#include <linux/regmap.h>
> +#include <linux/sysfs.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/stddef.h>
> +#include <linux/kthread.h>
> +
> +#define CLD_LABEL_LEN 64 /* label = "name:mode:offset" */
> +#define to_cld_reg(x) container_of(x, struct cld_data, bin)
> +
> +struct cld_register_info {
> + const char *name;
> + umode_t mode;
> + u8 reg;
> + u8 value;
> +};
> +
> +struct cld_data {
> + struct list_head list;
> + struct bin_attribute bin;
> + struct kernfs_node *kn;
> + struct cld_register_info info;
> +};
> +
> +struct cld_client {
> + struct bin_attribute new_register_bin;
> + struct bin_attribute delet_register_bin;
> + struct regmap *regmap;
> + struct device *dev;
> + struct cld_data *data;
> + struct task_struct *task;
> + size_t num_attributes;
> +};
> +
> +struct meta_cld_of_ops {
> + int (*load_registers)(struct cld_client *cld);
> +};
> +
> +static struct regmap_config cld_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .cache_type = REGCACHE_NONE,
> +};
> +
> +static ssize_t cld_register_read(struct file *flip, struct kobject *kobj,
> + struct bin_attribute *attr, char *buf,
> + loff_t pos, size_t count)
> +{
> + int ret;
> + unsigned int value;
> + struct device *dev = kobj_to_dev(kobj);
> + struct cld_client *cld = dev_get_drvdata(dev);
> + struct cld_data *data = to_cld_reg(attr);
> +
> + ret = regmap_read(cld->regmap, data->info.reg, &value);
> + if (ret != 0)
> + return ret;
> +
> + if ((data->info.mode & 0400) == 0400)
> + data->info.value = value;
> +
> + snprintf(buf, sizeof(value), "%d\n", value);
> +
> + return strlen(buf);
> +}
> +
> +static ssize_t cld_register_write(struct file *flip, struct kobject *kobj,
> + struct bin_attribute *attr, char *buf,
> + loff_t pos, size_t count)
> +{
> + int ret;
> + unsigned long val;
> + struct device *dev = kobj_to_dev(kobj);
> + struct cld_client *cld = dev_get_drvdata(dev);
> + struct cld_data *data = to_cld_reg(attr);
> +
> + ret = kstrtoul(buf, 0, &val);
> + if (ret)
> + goto out;
> +
> + if (val >= BIT(8)) {
> + ret = -EINVAL;
> + goto out;
> + }
> +
> + ret = regmap_write(cld->regmap, data->info.reg, val);
> + if (ret)
> + goto out;
> +
> +out:
> + return ret ? ret : strlen(buf);
> +}
> +
> +static int cld_bin_register(struct cld_register_info info,
> + struct cld_client *cld)
> +{
> + int ret;
> + struct cld_data *data, *pos;
> + struct bin_attribute *bin;
> + size_t length;
> +
> + list_for_each_entry(pos, &cld->data->list, list) {
> + length = (strlen(info.name) > strlen(pos->info.name)) ?
> + strlen(info.name):strlen(pos->info.name);
> + if (!strncasecmp(info.name, pos->info.name, length))
> + return -EEXIST;
> + }
> +
> + data = devm_kzalloc(cld->dev, sizeof(*data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + bin = &data->bin;
> + data->info = info;
> +
> + sysfs_bin_attr_init(bin);
> + bin->attr.name = kstrdup(info.name, GFP_KERNEL);
> + if (!bin->attr.name)
> + return -EINVAL;
> + bin->attr.mode = info.mode;
> + bin->read = cld_register_read;
> + bin->write = cld_register_write;
> + bin->size = 1;
> + ret = sysfs_create_bin_file(&cld->dev->kobj, bin);
> + if (ret) {
> + dev_err(cld->dev, "%s: failed to create file: %d\n",
> + info.name, ret);
> + goto out;
> + }
> +
> + data->kn = kernfs_find_and_get(cld->dev->kobj.sd, bin->attr.name);
> + if (!data->kn) {
> + sysfs_remove_bin_file(&cld->dev->kobj, bin);
> + ret = -EFAULT;
> + goto out;
> + }
> +
> + list_add_tail(&data->list, &cld->data->list);
> + ++cld->num_attributes;
> +out:
> + return ret;
> +}
> +
> +static int cld_bin_unregister(struct cld_register_info info,
> + struct cld_client *cld)
> +{
> + size_t length;
> + struct cld_data *pos;
> +
> + list_for_each_entry(pos, &cld->data->list, list) {
> + length = (strlen(info.name) > strlen(pos->info.name)) ?
> + strlen(info.name):strlen(pos->info.name);
> + if ((!strncasecmp(info.name, pos->info.name, length)) &&
> + (info.mode == pos->info.mode) &&
> + (info.reg == pos->info.reg)) {
> + kernfs_put(pos->kn);
> + sysfs_remove_bin_file(&cld->dev->kobj,
> + &pos->bin);
> + list_del(&pos->list);
> + devm_kfree(cld->dev, pos);
> + --cld->num_attributes;
> + return 0;
> + }
> + }
> +
> + dev_err(cld->dev, "%s: cannot match cld data\n", info.name);
> + return -EINVAL;
> +}
> +
> +static int cld_parse_label(char *label, struct cld_register_info *info)
> +{
> + char name[CLD_LABEL_LEN] = { 0 };
> + char *mode_str, *reg_str;
> + int rc, i;
> + unsigned long reg;
> + umode_t mode;
> + size_t length;
> + struct {
> + char *mode;
> + int value;
> + } options[] = {
> + {"rw", 0600},
> + {"r", 0400},
> + {"w", 0200},
> + };
> +
> + strncpy(name, label, CLD_LABEL_LEN);
> +
> + mode_str = strchr(name, ':');
> + if (!mode_str)
> + return -EINVAL;
> + *mode_str++ = '\0';
> +
> + reg_str = strchr(mode_str, ':');
> + if (!reg_str)
> + return -EINVAL;
> + *reg_str++ = '\0';
> +
> + if ((*name == '\0') || (*mode_str == '\0') || (*reg_str == '\0'))
> + return -EINVAL;
> +
> + for (i = 0; i < ARRAY_SIZE(options); i++) {
> + length = (strlen(options[i].mode) > strlen(mode_str)) ?
> + strlen(options[i].mode):strlen(mode_str);
> + if (strncasecmp(mode_str, options[i].mode, length) == 0) {
> + rc = kstrtoul(reg_str, 0, ®);
> + if (rc)
> + return -EINVAL;
> + mode = options[i].value;
> + break;
> + }
> + }
> + if ((i >= ARRAY_SIZE(options)) || (reg >= BIT(8)))
> + return -EINVAL;
> +
> + info->name = kstrdup(name, GFP_KERNEL);
> + if (!info->name)
> + return -EINVAL;
> + info->reg = reg;
> + info->mode = mode;
> + return 0;
> +}
> +
> +static int cld_load_registers(struct cld_client *cld, const char *property)
> +{
> + const char *label;
> + int count, ret, i;
> + struct cld_register_info info;
> + struct device *dev = cld->dev;
> +
> + count = of_property_count_strings(dev->of_node, property);
> + if (count <= 0)
> + return -EINVAL;
> +
> + for (i = 0; i < count; i++) {
> + ret = of_property_read_string_index(dev->of_node, property, i,
> + &label);
> + if (ret) {
> + dev_err(dev, ": failed to get label for index %d\n",
> + i);
> + continue;
> + }
> +
> + ret = cld_parse_label((char *)label, &info);
> + if (ret) {
> + dev_err(cld->dev, "%s: failed to parse label\n",
> + label);
> + continue;
> + }
> + cld_bin_register(info, cld);
> + }
> + return (count == cld->num_attributes) ? 0 : (-EINVAL);
> +}
> +
> +static int meta_cld_of_v1_load_registers(struct cld_client *cld)
> +{
> + int ret;
> +
> + ret = cld_load_registers(cld, "registers-map");
> + if (ret)
> + dev_dbg(cld->dev, "failed to load registers\n");
> +
> + return 0;
> +}
> +
> +static ssize_t cld_sysfs_new_register(struct file *filp, struct kobject *kobj,
> + struct bin_attribute *attr,
> + char *buf, loff_t pos, size_t count)
> +{
> + int ret;
> + struct device *dev = kobj_to_dev(kobj);
> + struct cld_client *cld = dev_get_drvdata(dev);
> + struct cld_register_info info;
> +
> + ret = cld_parse_label(buf, &info);
> + if (ret) {
> + dev_err(cld->dev, "failed to parse label\n");
> + goto out;
> + }
> + ret = cld_bin_register(info, cld);
> +
> +out:
> + return (!ret) ? count : ret;
> +}
> +
> +static ssize_t cld_sysfs_delete_register(struct file *filp,
> + struct kobject *kobj,
> + struct bin_attribute *attr,
> + char *buf, loff_t pos, size_t count)
> +{
> + int ret;
> + struct device *dev = kobj_to_dev(kobj);
> + struct cld_client *cld = dev_get_drvdata(dev);
> + struct cld_register_info info;
> +
> + ret = cld_parse_label(buf, &info);
> + if (ret) {
> + dev_err(cld->dev, "failed to parse label\n");
> + goto out;
> + }
> +
> + ret = cld_bin_unregister(info, cld);
> +
> +out:
> + return (!ret) ? count : ret;
> +}
> +
> +static int cld_monitor_thread(void *client)
> +{
> + struct cld_client *cld = client;
> + unsigned int value;
> + int ret;
> + struct cld_data *pos;
> +
> + while (!kthread_should_stop()) {
> + list_for_each_entry(pos, &cld->data->list, list) {
> + if ((pos->info.mode & 0400) == 0400) {
> + ret = regmap_read(cld->regmap, pos->info.reg,
> + &value);
> + if (ret)
> + continue;
> + if (pos->info.value != value) {
> + pos->info.value = value;
> + kernfs_notify(pos->kn);
> + }
> + }
> + }
> + msleep(50);
> + }
> + return 0;
> +}
> +
> +static int cld_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + int ret = 0;
> + const struct meta_cld_of_ops *ops;
> + struct device *dev = &client->dev;
> + struct cld_client *cld;
> +
> + cld = devm_kzalloc(dev, sizeof(*cld), GFP_KERNEL);
> + if (!cld) {
> + ret = -ENOMEM;
return
> + goto out;
> + }
> +
> + cld->dev = dev;
> + cld->num_attributes = 0;
> + cld->regmap = devm_regmap_init_i2c(client, &cld_regmap_config);
> + cld->data = devm_kzalloc(cld->dev, sizeof(struct cld_data),
sizeof(*)
> + GFP_KERNEL);
> + if (!cld->data) {
> + ret = -ENOMEM;
return
> + goto out;
> + }
> +
> + INIT_LIST_HEAD(&cld->data->list);
> +
> + sysfs_bin_attr_init(&cld->new_register_bin);
> + cld->new_register_bin.attr.name = "new_register";
> + cld->new_register_bin.attr.mode = 0200;
> + cld->new_register_bin.write = cld_sysfs_new_register;
> + ret = sysfs_create_bin_file(&dev->kobj, &cld->new_register_bin);
> + if (ret)
> + goto out;
> +
> + sysfs_bin_attr_init(&cld->delet_register_bin);
> + cld->delet_register_bin.attr.name = "delete_register";
> + cld->delet_register_bin.attr.mode = 0200;
> + cld->delet_register_bin.write = cld_sysfs_delete_register;
> + ret = sysfs_create_bin_file(&dev->kobj, &cld->delet_register_bin);
> + if (ret)
> + goto out;
return
> +
> + ops = of_device_get_match_data(cld->dev);
> + if (!ops) {
> + ret = -EINVAL;
return
> + goto out;
> + }
> +
> + ret = ops->load_registers(cld);
> +
> + cld->task = kthread_run(cld_monitor_thread, (void *)cld,
> + "register_monitor");
Why do you need the thread? What do you monitor? All this should be
explained and documented.
> + if (IS_ERR(cld->task)) {
> + ret = PTR_ERR(cld->task);
return
> + cld->task = NULL;
Drop
> + goto out;
> + }
> +
> + dev_set_drvdata(dev, cld);
This should happen before starting thread.
> +
> +out:
> + return ret;
> +}
> +
> +static int cld_remove(struct i2c_client *client)
> +{
> + struct device *dev = &client->dev;
> + struct cld_client *cld = dev_get_drvdata(dev);
> +
> + if (cld->task) {
> + kthread_stop(cld->task);
> + cld->task = NULL;
> + }
> +
> + devm_kfree(dev, cld);
> + return 0;
> +}
> +
> +static const struct meta_cld_of_ops of_v1_ops = {
> + .load_registers = meta_cld_of_v1_load_registers,
> +};
> +
> +static const struct of_device_id cld_of_match[] = {
This would warn now. Drop of_match_ptr.
> + {
> + .compatible = "meta,control-logic-device-v1",
> + .data = &of_v1_ops,
> + },
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(of, cld_of_match)
> +
> +static struct i2c_driver cld = {
> + .driver = { .name = "cld-driver",
> + .of_match_table = of_match_ptr(cld_of_match) },
Blank line before }
> + .probe = cld_probe,
> + .remove = cld_remove,
> +};
> +
> +module_i2c_driver(cld);
> +
> +MODULE_AUTHOR("Ren Chen <ren_chen@xxxxxxxxxx>");
> +MODULE_DESCRIPTION("Meta control logic device driver");
> +MODULE_LICENSE("GPL");
Best regards,
Krzysztof
