From: Tamal Saha <tamal.saha@xxxxxxxxx>
Intel Keem Bay platform supports multimaster operations over same i2c
bus using Synopsis i2c designware IP. When multi masters initiate i2c
operation simultaneously in a loop, SCL line is stucked low forever
after few i2c operations. Following interrupt sequences are observed
in:
working case: TX_EMPTY, RX_FULL and STOP_DET
non working case: TX_EMPTY, STOP_DET, RX_FULL.
DW_apb_i2c stretches the SCL line when the TX FIFO is empty or when
RX FIFO is full. The DW_apb_i2c master will continue to hold the SCL
line LOW until RX FIFO is read.
Linux kernel i2c designware software does not handle above non working
sequence. TX_EMPTY, RX_FULL and STOP_DET routine execution are required
in sequence although RX_FULL interrupt is raised after STOP_DET by
hardware. Clear STOP_DET for following conditions
(STOP_DET ,RX_FULL, rx_outstanding)
Write Operation: (1, 0, 0)
Read Operation:
RX_FULL followed by STOP_DET: (0, 1, 1) -> (1, 0, 0)
STOP_DET followed by RX_FULL: (1, 0, 1) -> (1, 1, 0)
RX_FULL and STOP_DET together: (1, 1, 1)
Signed-off-by: Tamal Saha <tamal.saha@xxxxxxxxx>
---
drivers/i2c/busses/i2c-designware-master.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/drivers/i2c/busses/i2c-designware-master.c b/drivers/i2c/busses/i2c-designware-master.c
index 9b08bb5df38d..9177463c2cbb 100644
--- a/drivers/i2c/busses/i2c-designware-master.c
+++ b/drivers/i2c/busses/i2c-designware-master.c
@@ -701,7 +701,8 @@ static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev)
regmap_read(dev->map, DW_IC_CLR_RX_DONE, &dummy);
if (stat & DW_IC_INTR_ACTIVITY)
regmap_read(dev->map, DW_IC_CLR_ACTIVITY, &dummy);
- if (stat & DW_IC_INTR_STOP_DET)
+ if ((stat & DW_IC_INTR_STOP_DET) &&
+ ((dev->rx_outstanding == 0) || (stat & DW_IC_INTR_RX_FULL)))
regmap_read(dev->map, DW_IC_CLR_STOP_DET, &dummy);
if (stat & DW_IC_INTR_START_DET)
regmap_read(dev->map, DW_IC_CLR_START_DET, &dummy);
@@ -723,6 +724,7 @@ static int i2c_dw_irq_handler_master(struct dw_i2c_dev *dev)
if (stat & DW_IC_INTR_TX_ABRT) {
dev->cmd_err |= DW_IC_ERR_TX_ABRT;
dev->status = STATUS_IDLE;
+ dev->rx_outstanding = 0;
/*
* Anytime TX_ABRT is set, the contents of the tx/rx
@@ -745,7 +747,8 @@ static int i2c_dw_irq_handler_master(struct dw_i2c_dev *dev)
*/
tx_aborted:
- if ((stat & (DW_IC_INTR_TX_ABRT | DW_IC_INTR_STOP_DET)) || dev->msg_err)
+ if (((stat & (DW_IC_INTR_TX_ABRT | DW_IC_INTR_STOP_DET)) || dev->msg_err) &&
+ (dev->rx_outstanding == 0))
complete(&dev->cmd_complete);
else if (unlikely(dev->flags & ACCESS_INTR_MASK)) {
/* Workaround to trigger pending interrupt */
--
2.17.1
