[PATCH v4 1/4] dt-bindings: i2c: aspeed: add transfer mode support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Append bindings to support transfer mode.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@xxxxxxxxxxxxxxx>
Reviewed-by: Brendan Higgins <brendanhiggins@xxxxxxxxxx>
---
Changes since v3:
- None

Changes since v2:
- Moved SRAM resources back to default dtsi and added mode selection
  property.

Changes since v1:
- Removed buffer reg settings from default device tree and added the settings
  into here to show the predefined buffer range per each bus.

 .../devicetree/bindings/i2c/i2c-aspeed.txt    | 37 +++++++++++++++----
 1 file changed, 30 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
index b47f6ccb196a..242343177324 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
@@ -17,6 +17,20 @@ Optional Properties:
 - bus-frequency	: frequency of the bus clock in Hz defaults to 100 kHz when not
 		  specified
 - multi-master	: states that there is another master active on this bus.
+- aspeed,i2c-xfer-mode	: should be "byte", "buf" or "dma" to select transfer
+			  mode defaults to "byte" mode when not specified.
+
+			  I2C DMA mode on AST2500 has these restrictions:
+			    - If one of these controllers is enabled
+				* UHCI host controller
+				* MCTP controller
+			      I2C has to use buffer mode or byte mode instead
+			      since these controllers run only in DMA mode and
+			      I2C is sharing the same DMA H/W with them.
+			    - If one of these controllers uses DMA mode, I2C
+			      can't use DMA mode
+				* SD/eMMC
+				* Port80 snoop
 
 Example:
 
@@ -26,20 +40,29 @@ i2c {
 	#size-cells = <1>;
 	ranges = <0 0x1e78a000 0x1000>;
 
-	i2c_ic: interrupt-controller@0 {
-		#interrupt-cells = <1>;
-		compatible = "aspeed,ast2400-i2c-ic";
+	i2c_gr: i2c-global-regs@0 {
+		compatible = "aspeed,ast2500-i2c-gr", "syscon";
 		reg = <0x0 0x40>;
-		interrupts = <12>;
-		interrupt-controller;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x40>;
+
+		i2c_ic: interrupt-controller@0 {
+			#interrupt-cells = <1>;
+			compatible = "aspeed,ast2500-i2c-ic";
+			reg = <0x0 0x4>;
+			interrupts = <12>;
+			interrupt-controller;
+		};
 	};
 
 	i2c0: i2c-bus@40 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		#interrupt-cells = <1>;
-		reg = <0x40 0x40>;
-		compatible = "aspeed,ast2400-i2c-bus";
+		reg = <0x40 0x40>, <0x200 0x10>;
+		compatible = "aspeed,ast2500-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB>;
 		resets = <&syscon ASPEED_RESET_I2C>;
 		bus-frequency = <100000>;
-- 
2.17.1




[Index of Archives]     [Linux GPIO]     [Linux SPI]     [Linux Hardward Monitoring]     [LM Sensors]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux