Since we have generic definitions for bus frequencies, let's use them.
Cc: Ray Jui <rjui@xxxxxxxxxxxx>
Cc: Scott Branden <sbranden@xxxxxxxxxxxx>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
---
drivers/i2c/busses/i2c-bcm-iproc.c | 14 +++++++-------
1 file changed, 7 insertions(+), 7 deletions(-)
diff --git a/drivers/i2c/busses/i2c-bcm-iproc.c b/drivers/i2c/busses/i2c-bcm-iproc.c
index 30efb7913b2e..627ad88dcf04 100644
--- a/drivers/i2c/busses/i2c-bcm-iproc.c
+++ b/drivers/i2c/busses/i2c-bcm-iproc.c
@@ -858,25 +858,25 @@ static int bcm_iproc_i2c_cfg_speed(struct bcm_iproc_i2c_dev *iproc_i2c)
if (ret < 0) {
dev_info(iproc_i2c->device,
"unable to interpret clock-frequency DT property\n");
- bus_speed = 100000;
+ bus_speed = I2C_STANDARD_MODE_FREQ;
}
- if (bus_speed < 100000) {
+ if (bus_speed < I2C_STANDARD_MODE_FREQ) {
dev_err(iproc_i2c->device, "%d Hz bus speed not supported\n",
bus_speed);
dev_err(iproc_i2c->device,
"valid speeds are 100khz and 400khz\n");
return -EINVAL;
- } else if (bus_speed < 400000) {
- bus_speed = 100000;
+ } else if (bus_speed < I2C_FAST_MODE_FREQ) {
+ bus_speed = I2C_STANDARD_MODE_FREQ;
} else {
- bus_speed = 400000;
+ bus_speed = I2C_FAST_MODE_FREQ;
}
iproc_i2c->bus_speed = bus_speed;
val = iproc_i2c_rd_reg(iproc_i2c, TIM_CFG_OFFSET);
val &= ~BIT(TIM_CFG_MODE_400_SHIFT);
- val |= (bus_speed == 400000) << TIM_CFG_MODE_400_SHIFT;
+ val |= (bus_speed == I2C_FAST_MODE_FREQ) << TIM_CFG_MODE_400_SHIFT;
iproc_i2c_wr_reg(iproc_i2c, TIM_CFG_OFFSET, val);
dev_info(iproc_i2c->device, "bus set to %u Hz\n", bus_speed);
@@ -1029,7 +1029,7 @@ static int bcm_iproc_i2c_resume(struct device *dev)
/* configure to the desired bus speed */
val = iproc_i2c_rd_reg(iproc_i2c, TIM_CFG_OFFSET);
val &= ~BIT(TIM_CFG_MODE_400_SHIFT);
- val |= (iproc_i2c->bus_speed == 400000) << TIM_CFG_MODE_400_SHIFT;
+ val |= (iproc_i2c->bus_speed == I2C_FAST_MODE_FREQ) << TIM_CFG_MODE_400_SHIFT;
iproc_i2c_wr_reg(iproc_i2c, TIM_CFG_OFFSET, val);
bcm_iproc_i2c_enable_disable(iproc_i2c, true);
--
2.25.0
