Re: [PATCH v2 6/7] dt-bindings: serial: Add bindings for GENI based UART Controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 1/16/2018 11:35 PM, Bjorn Andersson wrote:
On Fri 12 Jan 17:05 PST 2018, Karthikeyan Ramasubramanian wrote:

Add device tree binding support for GENI based UART Controller in the
QUP Wrapper.

Signed-off-by: Karthikeyan Ramasubramanian <kramasub@xxxxxxxxxxxxxx>
Signed-off-by: Girish Mahadevan <girishm@xxxxxxxxxxxxxx>
---
  .../devicetree/bindings/serial/qcom,geni-uart.txt  | 29 ++++++++++++++++++++++
  .../devicetree/bindings/soc/qcom/qcom,geni-se.txt  | 13 ++++++++++
  2 files changed, 42 insertions(+)
  create mode 100644 Documentation/devicetree/bindings/serial/qcom,geni-uart.txt

diff --git a/Documentation/devicetree/bindings/serial/qcom,geni-uart.txt b/Documentation/devicetree/bindings/serial/qcom,geni-uart.txt
new file mode 100644
index 0000000..e7b9e24
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/qcom,geni-uart.txt
@@ -0,0 +1,29 @@
+Qualcomm Technologies Inc. GENI Serial Engine based UART Controller
+
+The Generic Interface (GENI) Serial Engine based UART controller supports
+console use-cases and is supported only by GENI based Qualcomm Universal
+Peripheral (QUP) cores.
+
+Required properties:
+- compatible: should contain "qcom,geni-debug-uart".

Why is this uart a _debug_ uart? Is there a separate binding for the
geni-uart?
Yes. It will be uploaded at a later point in time.

I like that your naming here matches my suggestion with qcom,geni-i2c.

+- reg: Should contain UART register location and length.
+- reg-names: Should contain "se-phys".

No need to specify reg-names for a single reg.
Ok.

+- interrupts: Should contain UART core interrupts.
+- clock-names: Should contain "se-clk".

Omit the "clk"
Ok.

+- clocks: clocks needed for UART, includes the core clock.

Be more specific.
Ok.

+- pinctrl-names/pinctrl-0/1: The GPIOs assigned to this core. The names
+  Should be "active" and "sleep" for the pin confuguration when core is active
+  or when entering sleep state.

Omit pinctrl information.
Ok.

+
+Example:
+uart0: qcom,serial@a88000 {

Don't use qcom, in node name. This should be named "serial".
Ok.

+	compatible = "qcom,geni-debug-uart";
+	reg = <0xa88000 0x7000>;
+	reg-names = "se-phys";
+	interrupts = <0 355 0>;

<GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>
Ok.

+	clock-names = "se-clk";
+	clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qup_1_uart_3_active>;
+	pinctrl-1 = <&qup_1_uart_3_sleep>;
+};

Regards,
Bjorn

Regards,
Karthik.
--
Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project



[Index of Archives]     [Linux GPIO]     [Linux SPI]     [Linux Hardward Monitoring]     [LM Sensors]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux