Start RuntimePM a bit earlier, so we can use it to enable the clock
during probe for frequency calculations. Make sure it is enabled before
calling setup().
Signed-off-by: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx>
---
drivers/i2c/busses/i2c-sh_mobile.c | 35 +++++++++++++++++------------------
1 file changed, 17 insertions(+), 18 deletions(-)
diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c
index 88af45225003a5..f1a9b971e2c14a 100644
--- a/drivers/i2c/busses/i2c-sh_mobile.c
+++ b/drivers/i2c/busses/i2c-sh_mobile.c
@@ -252,11 +252,7 @@ static int sh_mobile_i2c_init(struct sh_mobile_i2c_data *pd)
u32 tHIGH, tLOW, tf;
uint16_t max_val;
- /* Get clock rate after clock is enabled */
- clk_prepare_enable(pd->clk);
- i2c_clk_khz = clk_get_rate(pd->clk) / 1000;
- clk_disable_unprepare(pd->clk);
- i2c_clk_khz /= pd->clks_per_count;
+ i2c_clk_khz = clk_get_rate(pd->clk) / 1000 / pd->clks_per_count;
if (pd->bus_speed == STANDARD_MODE) {
tLOW = 47; /* tLOW = 4.7 us */
@@ -881,6 +877,20 @@ static int sh_mobile_i2c_probe(struct platform_device *dev)
if (resource_size(res) > 0x17)
pd->flags |= IIC_FLAG_HAS_ICIC67;
+ /* Enable Runtime PM for this device.
+ *
+ * Also tell the Runtime PM core to ignore children
+ * for this device since it is valid for us to suspend
+ * this I2C master driver even though the slave devices
+ * on the I2C bus may not be suspended.
+ *
+ * The state of the I2C hardware bus is unaffected by
+ * the Runtime PM state.
+ */
+ pm_suspend_ignore_children(&dev->dev, true);
+ pm_runtime_enable(&dev->dev);
+ pm_runtime_get_sync(&dev->dev);
+
config = of_device_get_match_data(&dev->dev);
if (config) {
pd->clks_per_count = config->clks_per_count;
@@ -888,6 +898,8 @@ static int sh_mobile_i2c_probe(struct platform_device *dev)
} else {
ret = sh_mobile_i2c_init(pd);
}
+
+ pm_runtime_put_sync(&dev->dev);
if (ret)
return ret;
@@ -896,19 +908,6 @@ static int sh_mobile_i2c_probe(struct platform_device *dev)
pd->dma_direction = DMA_NONE;
pd->dma_rx = pd->dma_tx = ERR_PTR(-EPROBE_DEFER);
- /* Enable Runtime PM for this device.
- *
- * Also tell the Runtime PM core to ignore children
- * for this device since it is valid for us to suspend
- * this I2C master driver even though the slave devices
- * on the I2C bus may not be suspended.
- *
- * The state of the I2C hardware bus is unaffected by
- * the Runtime PM state.
- */
- pm_suspend_ignore_children(&dev->dev, true);
- pm_runtime_enable(&dev->dev);
-
/* setup the private data */
adap = &pd->adap;
i2c_set_adapdata(adap, pd);
--
2.11.0
