On Mon, Apr 03, 2017 at 01:09:14PM +0200, Hans de Goede wrote: > The INT33FE ACPI device has a CRS table with I2cSerialBusV2 resources for > 3 devices: Maxim MAX17047 Fuel Gauge Controller, FUSB300C USB Type-C > Controller and PI3USB30532 USB switch. +Rafael > > This commit adds a driver for this ACPI device which instantiates > i2c-clients for these, so that the standard i2c drivers for these chips > can bind to the them. Out of curiosity, has Intel provided any documentation for this HID? If not, Mika, Andy, this would be a good opportunity to push on the "Default to open" policy for ACPI device specs. I'd suggest raising with Mark Doran as he's been helping us with that in the past. This is independent of this patch, just something that will require constant tending and nagging to affect change there. A few comments/questions below... > > Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx> > --- > Changes in v4: > -This is a new patch in v4 of this patch-set replacing the > cht_wc_fuel_gauge driver which was binding to the INT33FE device before > I figured out this is some sort of meta device describing 3 devices > and that the fuel-guage really is just a Maxim MAX17047. The > cht_wc_fuel_gauge driver will be replaced by a max17047 driver which I > will submit seperately > --- > drivers/platform/x86/Kconfig | 13 +++ > drivers/platform/x86/Makefile | 1 + > drivers/platform/x86/intel_cht_int33fe.c | 144 +++++++++++++++++++++++++++++++ > 3 files changed, 158 insertions(+) > create mode 100644 drivers/platform/x86/intel_cht_int33fe.c > > diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig > index 6a5b79c..57f7c1d 100644 > --- a/drivers/platform/x86/Kconfig > +++ b/drivers/platform/x86/Kconfig > @@ -772,6 +772,19 @@ config ACPI_CMPC > keys as input device, backlight device, tablet and accelerometer > devices. > > +config INTEL_CHT_INT33FE > + tristate "Intel Cherry Trail ACPI INT33FE Driver" > + depends on X86 && ACPI > + ---help--- > + This driver add support for the INT33FE ACPI device found on > + some Intel Cherry Trail devices. > + > + The INT33FE ACPI device has a CRS table with I2cSerialBusV2 > + resources for 3 devices: Maxim MAX17047 Fuel Gauge Controller, > + FUSB300C USB Type-C Controller and PI3USB30532 USB switch. > + This driver instantiates i2c-clients for these, so that standard > + i2c drivers for these chips can bind to the them. > + > config INTEL_HID_EVENT > tristate "INTEL HID Event" > depends on ACPI > diff --git a/drivers/platform/x86/Makefile b/drivers/platform/x86/Makefile > index 6d4b01a..6731893 100644 > --- a/drivers/platform/x86/Makefile > +++ b/drivers/platform/x86/Makefile > @@ -44,6 +44,7 @@ obj-$(CONFIG_ACPI_TOSHIBA) += toshiba_acpi.o > obj-$(CONFIG_TOSHIBA_BT_RFKILL) += toshiba_bluetooth.o > obj-$(CONFIG_TOSHIBA_HAPS) += toshiba_haps.o > obj-$(CONFIG_TOSHIBA_WMI) += toshiba-wmi.o > +obj-$(CONFIG_INTEL_CHT_INT33FE) += intel_cht_int33fe.o > obj-$(CONFIG_INTEL_HID_EVENT) += intel-hid.o > obj-$(CONFIG_INTEL_VBTN) += intel-vbtn.o > obj-$(CONFIG_INTEL_SCU_IPC) += intel_scu_ipc.o > diff --git a/drivers/platform/x86/intel_cht_int33fe.c b/drivers/platform/x86/intel_cht_int33fe.c > new file mode 100644 > index 0000000..3a06426 > --- /dev/null > +++ b/drivers/platform/x86/intel_cht_int33fe.c > @@ -0,0 +1,144 @@ > +/* > + * Intel Cherry Trail ACPI INT33FE pseudo device driver > + * > + * Copyright (C) 2017 Hans de Goede <hdegoede@xxxxxxxxxx> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + * > + * Some Intel Cherry Trail based device which ship with Windows 10, have > + * this weird INT33FE ACPI device with a CRS table with 4 I2cSerialBusV2 > + * resources, for 4 different chips attached to various i2c busses: > + * 1. The Whiskey Cove pmic, which is also described by the INT34D3 ACPI device > + * 2. Maxim MAX17047 Fuel Gauge Controller > + * 3. FUSB300C USB Type-C Controller > + * 4. PI3USB30532 USB switch > + * > + * So this driver is a stub / pseudo driver whose only purpose is to > + * instantiate i2c-clients for chips 2 - 4, so that standard i2c drivers > + * for these chips can bind to the them. What about 1. Whiskey Cove PMIC? Are we ignoring that resource in lieu of the INT34D3 HID? Do they both provide the same resources? > + */ > + > +#include <linux/acpi.h> > +#include <linux/i2c.h> > +#include <linux/interrupt.h> > +#include <linux/module.h> > +#include <linux/power/acpi.h> > +#include <linux/slab.h> > + > +#define EXPECTED_PTYPE 4 > + > +struct cht_int33fe_data { > + struct i2c_client *max17047; > + struct i2c_client *fusb300c; > + struct i2c_client *pi3usb30532; > +}; > + > +static int cht_int33fe_probe(struct i2c_client *client) > +{ > + struct device *dev = &client->dev; > + struct i2c_board_info board_info; > + struct cht_int33fe_data *data; > + acpi_status status; > + unsigned long long ptyp; Minor nit, prefered ordering is longest to shortest, "Reverse Christmas Tree Order", just move ptyp up a line. > + int fusb300c_irq; > + > + status = acpi_evaluate_integer(ACPI_HANDLE(dev), "PTYP", NULL, &ptyp); > + if (ACPI_FAILURE(status)) { > + dev_err(dev, "Error getting PTYPE\n"); > + return -ENODEV; > + } > + > + /* > + * The same ACPI HID is used for different configurations check PTYP > + * to ensure that we are dealing with the expected config. > + */ > + if (ptyp != EXPECTED_PTYPE) > + return -ENODEV; > + Are any of the other configurations known and relevant? > + /* The FUSB300C uses the irq at index 1 and is the only irq user */ > + fusb300c_irq = acpi_dev_gpio_irq_get(ACPI_COMPANION(dev), 1); > + if (fusb300c_irq < 0) { > + if (fusb300c_irq != -EPROBE_DEFER) > + dev_err(dev, "Error getting FUSB300C irq\n"); > + return fusb300c_irq; > + } Since this driver is a dependency for 3 devices, is it correct to abort here if 1 of the 3 fails? I could see it making sense to issue the warning, but continue on so the other two devices could be setup. On the other hand, if PTYP 4 means the USB irq should be defined, then perhaps if that fails we don't trust any of it and just bail out. What was your rationale for the chosen approach? > + > + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); > + if (!data) > + return -ENOMEM; > + > + memset(&board_info, 0, sizeof(board_info)); > + strlcpy(board_info.type, "max17047", I2C_NAME_SIZE); > + > + data->max17047 = i2c_acpi_new_device(dev, 1, &board_info); > + if (!data->max17047) > + return -EPROBE_DEFER; /* Wait for the i2c-adapter to load */ > + > + memset(&board_info, 0, sizeof(board_info)); > + strlcpy(board_info.type, "fusb300c", I2C_NAME_SIZE); > + board_info.irq = fusb300c_irq; > + > + data->fusb300c = i2c_acpi_new_device(dev, 2, &board_info); > + if (!data->fusb300c) > + goto out_unregister_max17047; > + > + memset(&board_info, 0, sizeof(board_info)); > + strlcpy(board_info.type, "pi3usb30532", I2C_NAME_SIZE); > + > + data->pi3usb30532 = i2c_acpi_new_device(dev, 3, &board_info); > + if (!data->pi3usb30532) > + goto out_unregister_fusb300c; > + > + i2c_set_clientdata(client, data); > + > + return 0; > + > +out_unregister_fusb300c: > + i2c_unregister_device(data->fusb300c); > + > +out_unregister_max17047: > + i2c_unregister_device(data->max17047); > + > + return -EPROBE_DEFER; /* Wait for the i2c-adapter to load */ > +} > + > +static int cht_int33fe_remove(struct i2c_client *i2c) > +{ > + struct cht_int33fe_data *data = i2c_get_clientdata(i2c); > + > + i2c_unregister_device(data->pi3usb30532); > + i2c_unregister_device(data->fusb300c); > + i2c_unregister_device(data->max17047); > + > + return 0; > +} > + > +static const struct i2c_device_id cht_int33fe_i2c_id[] = { > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, cht_int33fe_i2c_id); > + > +static const struct acpi_device_id cht_int33fe_acpi_ids[] = { > + { "INT33FE", }, > + { } > +}; > +MODULE_DEVICE_TABLE(acpi, cht_int33fe_acpi_ids); > + > +static struct i2c_driver cht_int33fe_driver = { > + .driver = { > + .name = "Intel Cherry Trail ACPI INT33FE driver", > + .acpi_match_table = ACPI_PTR(cht_int33fe_acpi_ids), > + }, > + .probe_new = cht_int33fe_probe, > + .remove = cht_int33fe_remove, > + .id_table = cht_int33fe_i2c_id, > + .disable_i2c_core_irq_mapping = true, > +}; > + > +module_i2c_driver(cht_int33fe_driver); > + > +MODULE_DESCRIPTION("Intel Cherry Trail ACPI INT33FE pseudo device driver"); > +MODULE_AUTHOR("Hans de Goede <hdegoede@xxxxxxxxxx>"); > +MODULE_LICENSE("GPL"); > -- > 2.9.3 > > -- Darren Hart VMware Open Source Technology Center -- To unsubscribe from this list: send the line "unsubscribe linux-i2c" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html