---
.../devicetree/bindings/i2c/i2c-mux-simple.txt | 91 ++++++++++++++++++++++
1 file changed, 91 insertions(+)
create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-simple.txt
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-simple.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-simple.txt
new file mode 100644
index 000000000000..fec1ab39ad64
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-simple.txt
@@ -0,0 +1,91 @@
+Simple I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses GPIOs to
+route the I2C signals.
+
+ .-----. .-----.
+ | dev | | dev |
+ .------------. '-----' '-----'
+ | SoC | | |
+ | | .--------+--------'
+ | .------. | .------+ child bus A, on MUX value set to 0
+ | | I2C |-|--| Mux |
+ | '------' | '--+---+ child bus B, on MUX value set to 1
+ | .------. | | '----------+--------+--------.
+ | | MUX- | | | | | |
+ | | Ctrl |-|-----+ .-----. .-----. .-----.
+ | '------' | | dev | | dev | | dev |
+ '------------' '-----' '-----' '-----'
+
+Required properties:
+- compatible: i2c-mux-simple,mux-locked or i2c-mux-simple,parent-locked
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+ port is connected to.
+- control-muxes : Node of the multiplexer that controls "Mux".
+- control-mux-names : Should be "mux".
+* Standard I2C mux properties. See i2c-mux.txt in this directory.
+* I2C child bus nodes. See i2c-mux.txt in this directory.
+
+Optional properties:
+- idle-state: value to set the muxer to when idle. When no value is
+ given, it defaults to the last value used.
+
+For each i2c child node, an I2C child bus will be created. They will
+be numbered based on their order in the device tree.
+
+Whenever an access is made to a device on a child bus, the value set
+in the relevant node's reg property will be fed to the mux controller.
+
+If an idle state is defined, using the idle-state (optional) property,
+whenever an access is not being made to a device on a child bus, the
+mux controller will be set according to the idle value.
+
+If an idle state is not defined, the most recently used value will be
+left programmed into hardware whenever no access is being made to a
+device on a child bus.
+
+Example:
+ control_i2c_mux: control-i2c-mux {
+ compatible = "mux-gpio";
+
+ mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
+ <&pioA 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ i2c-mux {
+ compatible = "i2c-mux-simple,mux-locked";
+ i2c-parent = <&i2c1>;
+
+ control-muxes = <&control_i2c_mux>;
+ control-mux-names = "mux";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ssd1307: oled@3c {
+ compatible = "solomon,ssd1307fb-i2c";
+ reg = <0x3c>;
+ pwms = <&pwm 4 3000>;
+ reset-gpios = <&gpio2 7 1>;
+ reset-active-low;
+ };
+ };
+
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pca9555: pca9555@20 {
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+ };
+ };
+ };
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
