+additional lists
> Add support to get the device parameters from ACPI. Assume that the clocks
> are managed by firmware.
>
> Signed-off-by: Naveen Kaje <nkaje@xxxxxxxxxxxxxx>
> ---
<snip>
> + bool input_clk_ctrl = true;
>
> qup = devm_kzalloc(&pdev->dev, sizeof(*qup), GFP_KERNEL);
> if (!qup)
> @@ -1372,7 +1378,14 @@ static int qup_i2c_probe(struct platform_device
> *pdev)
> init_completion(&qup->xfer);
> platform_set_drvdata(pdev, qup);
>
> - of_property_read_u32(node, "clock-frequency", &clk_freq);
> + ret = device_property_read_u32(qup->dev, "clock-frequency",
> &clk_freq);
> + if (ret) {
> + dev_warn(qup->dev, "using default clock-frequency values");
> + clk_freq = DEFAULT_CLK_FREQ;
> + }
> +
> + if (ACPI_HANDLE(qup->dev) && !node)
> + input_clk_ctrl = false;
>
> if (of_device_is_compatible(pdev->dev.of_node, "qcom,i2c-qup-
> v1.1.1")) {
> qup->adap.algo = &qup_i2c_algo;
> @@ -1454,20 +1467,29 @@ nodma:
> return qup->irq;
> }
>
> - qup->clk = devm_clk_get(qup->dev, "core");
> - if (IS_ERR(qup->clk)) {
> - dev_err(qup->dev, "Could not get core clock\n");
> - return PTR_ERR(qup->clk);
> - }
> + if (input_clk_ctrl) {
The above ACPI_HANDLE check can be directly used here and avoid the
variable.
> + qup->clk = devm_clk_get(qup->dev, "core");
> + if (IS_ERR(qup->clk)) {
> + dev_err(qup->dev, "Could not get core clock\n");
> + return PTR_ERR(qup->clk);
> + }
>
> - qup->pclk = devm_clk_get(qup->dev, "iface");
> - if (IS_ERR(qup->pclk)) {
> - dev_err(qup->dev, "Could not get iface clock\n");
> - return PTR_ERR(qup->pclk);
> + qup->pclk = devm_clk_get(qup->dev, "iface");
> + if (IS_ERR(qup->pclk)) {
> + dev_err(qup->dev, "Could not get iface clock\n");
> + return PTR_ERR(qup->pclk);
> + }
> + qup_i2c_enable_clocks(qup);
> + src_clk_freq = clk_get_rate(qup->clk);
> + } else {
> + ret = device_property_read_u32(qup->dev,
> + "src-clock-hz", &src_clk_freq);
> + if (ret) {
> + dev_warn(qup->dev, "using default src-clock-hz");
> + src_clk_freq = DEFAULT_SRC_CLK;
> + }
> }
>
> - qup_i2c_enable_clocks(qup);
> -
> /*
> * Bootloaders might leave a pending interrupt on certain QUP's,
> * so we reset the core before registering for interrupts.
> @@ -1514,7 +1536,6 @@ nodma:
> size = QUP_INPUT_FIFO_SIZE(io_mode);
> qup->in_fifo_sz = qup->in_blk_sz * (2 << size);
>
> - src_clk_freq = clk_get_rate(qup->clk);
> fs_div = ((src_clk_freq / clk_freq) / 2) - 3;
> hs_div = 3;
> qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); @@ -1534,6 +1555,8
> @@ nodma:
> qup->adap.dev.parent = qup->dev;
> qup->adap.dev.of_node = pdev->dev.of_node;
> qup->is_last = true;
> + if (ACPI_HANDLE(qup->dev))
> + ACPI_COMPANION_SET(&qup->adap.dev,
> ACPI_COMPANION(qup->dev));
Can we move this inside the above check.
>
> strlcpy(qup->adap.name, "QUP I2C adapter", sizeof(qup-
> >adap.name));
>
> @@ -1639,6 +1662,13 @@ static const struct of_device_id
> qup_i2c_dt_match[] = { }; MODULE_DEVICE_TABLE(of, qup_i2c_dt_match);
>
> +#if IS_ENABLED(CONFIG_ACPI)
> +static const struct acpi_device_id qup_i2c_acpi_match[] = {
> + { "QCOM8010"},
> + { },
> +};
> +MODULE_DEVICE_TABLE(acpi, qup_i2c_acpi_ids); #endif
> static struct platform_driver qup_i2c_driver = {
> .probe = qup_i2c_probe,
> .remove = qup_i2c_remove,
> @@ -1646,6 +1676,7 @@ static struct platform_driver qup_i2c_driver = {
> .name = "i2c_qup",
> .pm = &qup_i2c_qup_pm_ops,
> .of_match_table = qup_i2c_dt_match,
> + .acpi_match_table = ACPI_PTR(qup_i2c_acpi_match),
Should this also be in #if IS_ENABLED(CONFIG_ACPI) check ?
Regards,
Sricharan
--
To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
