On Thu, Jan 17, 2013 at 12:42:47PM +0200, Mika Westerberg wrote:
> On Thu, Jan 17, 2013 at 12:32:48PM +0200, Felipe Balbi wrote:
> > Hi,
> >
> > On Thu, Jan 17, 2013 at 12:31:05PM +0200, Mika Westerberg wrote:
> > > If IC_EMPTYFIFO_HOLD_MASTER_EN is set to one, the DesignWare I2C controller
> > > doesn't generate STOP on the bus when the FIFO is empty. This violates the
> > > rules of Linux I2C stack as it requires that the STOP is issued once the
> > > i2c_transfer() is finished.
> > >
> > > However, there is no way to detect this from the hardware registers, so we
> > > must make sure that the STOP bit is always set once the last byte of the
> > > last message is transferred.
> > >
> > > This patch is based on the work of Dirk Brandewie.
> > >
> > > Signed-off-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
> > > ---
> > > drivers/i2c/busses/i2c-designware-core.c | 16 ++++++++++++++--
> > > 1 file changed, 14 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c
> > > index f5258c2..94fd818 100644
> > > --- a/drivers/i2c/busses/i2c-designware-core.c
> > > +++ b/drivers/i2c/busses/i2c-designware-core.c
> > > @@ -413,11 +413,23 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev)
> > > rx_limit = dev->rx_fifo_depth - dw_readl(dev, DW_IC_RXFLR);
> > >
> > > while (buf_len > 0 && tx_limit > 0 && rx_limit > 0) {
> > > + u32 cmd = 0;
> > > +
> > > + /*
> > > + * If IC_EMPTYFIFO_HOLD_MASTER_EN is set we must
> > > + * manually set the stop bit. However, it cannot be
> > > + * detected from the registers so we set it always
> > > + * when writing/reading the last byte.
> > > + */
> > > + if (dev->msg_write_idx == dev->msgs_num - 1 &&
> > > + buf_len == 1)
> > > + cmd |= BIT(9);
> > > +
> > > if (msgs[dev->msg_write_idx].flags & I2C_M_RD) {
> > > - dw_writel(dev, 0x100, DW_IC_DATA_CMD);
> > > + dw_writel(dev, cmd | 0x100, DW_IC_DATA_CMD);
> > > rx_limit--;
> > > } else
> > > - dw_writel(dev, *buf++, DW_IC_DATA_CMD);
> > > + dw_writel(dev, cmd | *buf++, DW_IC_DATA_CMD);
> >
> > also need to send STP bit if I2C_M_STOP is set.
>
> True but only if the driver exposes I2C_FUNC_PROTOCOL_MANGLING, which is
> not done in this driver.
right, didn't check the driver, my bad.
--
balbi
Attachment:
signature.asc
Description: Digital signature
