From: Vikram Pandita <vikram.pandita@xxxxxx> In case a peripheral is driving SDA bus low (ie. a start condition), provide a constant clock output using the test mode of the OMAP I2C controller to try and clear the bus. Soft reset I2C controller after attempting the bus clear to ensure that controller is in a good state. Based upon Vikram Pandita's patch from TI Android 3.0. I acknowledge the contributions and suggestions of Jon and Hemant. A couple differences from the original patch ... 1. Add a new function for bus clear 2. Ensure that the CON.I2C_EN bit is set when using the SYSTEST feature to output a permanent clock. This bit needs to be set and typically it would be set by the unidle function but this is not the case for all OMAP generations. 3. Program the SYSTEST setting only the bits we care about. However, restore SYSTEST registers to there original state as some OMAP generations do not implement perform a soft-reset. 4. Clear the CON register after performing the bus clear, so when we call the init function the controller is disabled and the init function will re-enable later. Original patch can be found here: http://git.omapzoom.org/?p=kernel/omap.git;a=commit;h=a2ab04192ba25e60f95ba1ff3af5601a2d7b5bd1 Signed-off-by: Vikram Pandita <vikram.pandita@xxxxxx> Signed-off-by: Jon Hunter <jon-hunter@xxxxxx> Signed-off-by: Shubhrajyoti D <shubhrajyoti@xxxxxx> --- drivers/i2c/busses/i2c-omap.c | 33 ++++++++++++++++++++++++++++++--- 1 files changed, 30 insertions(+), 3 deletions(-) diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index e402ebb..a882558 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -147,16 +147,15 @@ enum { #define OMAP_I2C_SCLH_HSSCLH 8 /* I2C System Test Register (OMAP_I2C_SYSTEST): */ -#ifdef DEBUG #define OMAP_I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */ #define OMAP_I2C_SYSTEST_FREE (1 << 14) /* Free running mode */ #define OMAP_I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */ -#define OMAP_I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */ +#define OMAP_I2C_SYSTEST_TMODE_TEST (2 << 12) /* Test mode select */ +#define OMAP_I2C_SYSTEST_TMODE_LOOP (3 << 12) /* Test mode select */ #define OMAP_I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense in */ #define OMAP_I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive out */ #define OMAP_I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense in */ #define OMAP_I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive out */ -#endif /* OCP_SYSSTATUS bit definitions */ #define SYSS_RESETDONE_MASK (1 << 0) @@ -319,6 +318,7 @@ static int omap_i2c_reset(struct omap_i2c_dev *dev) dev->westate); } } + return 0; } static int omap_i2c_init(struct omap_i2c_dev *dev) @@ -471,6 +471,31 @@ static int omap_i2c_wait_for_bb(struct omap_i2c_dev *dev) } /* + * Bus Clear + */ +static int omap_i2c_bus_clear(struct omap_i2c_dev *dev) +{ + u16 w; + + /* + * Per the I2C specification, if we are stuck in a bus busy state + * we can attempt a bus clear to try and recover the bus by sending + * at least 9 clock pulses on SCL. Put the I2C in a test mode so it + * will output a continuous clock on SCL. + */ + w = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG); + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); + omap_i2c_write_reg(dev, OMAP_I2C_SYSTEST_REG, (OMAP_I2C_SYSTEST_ST_EN + | OMAP_I2C_SYSTEST_TMODE_TEST)); + msleep(1); + omap_i2c_write_reg(dev, OMAP_I2C_SYSTEST_REG, w); + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); + omap_i2c_reset(dev); + omap_i2c_init(dev); + return omap_i2c_wait_for_bb(dev); +} + +/* * Low level master read/write transaction. */ static int omap_i2c_xfer_msg(struct i2c_adapter *adap, @@ -597,6 +622,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) r = omap_i2c_wait_for_bb(dev); if (r < 0) + r = omap_i2c_bus_clear(dev); + if (r < 0) goto out; if (dev->set_mpu_wkup_lat != NULL) -- 1.7.4.1 -- To unsubscribe from this list: send the line "unsubscribe linux-i2c" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
