Superseded by tdfxfb. I2C/DDC support used to live in a separate driver but this caused driver conflicts. Signed-off-by: Jean Delvare <khali@xxxxxxxxxxxx> Cc: Krzysztof Helt <krzysztof.h1@xxxxx> --- Scheduled for kernel 2.6.33. Documentation/feature-removal-schedule.txt | 9 - Documentation/i2c/busses/i2c-voodoo3 | 62 ------- drivers/i2c/busses/Kconfig | 16 - drivers/i2c/busses/Makefile | 3 drivers/i2c/busses/i2c-voodoo3.c | 248 ---------------------------- 5 files changed, 338 deletions(-) --- linux-2.6.32-pre.orig/Documentation/feature-removal-schedule.txt 2009-09-18 18:56:51.000000000 +0200 +++ linux-2.6.32-pre/Documentation/feature-removal-schedule.txt 2009-09-18 23:04:29.000000000 +0200 @@ -412,15 +412,6 @@ Who: Alex Chiang <achiang@xxxxxx> --------------------------- -What: i2c-voodoo3 driver -When: October 2009 -Why: Superseded by tdfxfb. I2C/DDC support used to live in a separate - driver but this caused driver conflicts. -Who: Jean Delvare <khali@xxxxxxxxxxxx> - Krzysztof Helt <krzysztof.h1@xxxxx> - ---------------------------- - What: CONFIG_RFKILL_INPUT When: 2.6.33 Why: Should be implemented in userspace, policy daemon. --- linux-2.6.32-pre.orig/Documentation/i2c/busses/i2c-voodoo3 2009-06-10 05:05:27.000000000 +0200 +++ /dev/null 1970-01-01 00:00:00.000000000 +0000 @@ -1,62 +0,0 @@ -Kernel driver i2c-voodoo3 - -Supported adapters: - * 3dfx Voodoo3 based cards - * Voodoo Banshee based cards - -Authors: - Frodo Looijaard <frodol@xxxxxx>, - Philip Edelbrock <phil@xxxxxxxxxxxxx>, - Ralph Metzler <rjkm@xxxxxxxxxxxxxxxx>, - Mark D. Studebaker <mdsxyz123@xxxxxxxxx> - -Main contact: Philip Edelbrock <phil@xxxxxxxxxxxxx> - -The code is based upon Ralph's test code (he did the hard stuff ;') - -Description ------------ - -The 3dfx Voodoo3 chip contains two I2C interfaces (aka a I2C 'master' or -'host'). - -The first interface is used for DDC (Data Display Channel) which is a -serial channel through the VGA monitor connector to a DDC-compliant -monitor. This interface is defined by the Video Electronics Standards -Association (VESA). The standards are available for purchase at -http://www.vesa.org . - -The second interface is a general-purpose I2C bus. The intent by 3dfx was -to allow manufacturers to add extra chips to the video card such as a -TV-out chip such as the BT869 or possibly even I2C based temperature -sensors like the ADM1021 or LM75. - -Stability ---------- - -Seems to be stable on the test machine, but needs more testing on other -machines. Simultaneous accesses of the DDC and I2C busses may cause errors. - -Supported Devices ------------------ - -Specifically, this driver was written and tested on the '3dfx Voodoo3 AGP -3000' which has a tv-out feature (s-video or composite). According to the -docs and discussions, this code should work for any Voodoo3 based cards as -well as Voodoo Banshee based cards. The DDC interface has been tested on a -Voodoo Banshee card. - -Issues ------- - -Probably many, but it seems to work OK on my system. :') - - -External Device Connection --------------------------- - -The digital video input jumpers give availability to the I2C bus. -Specifically, pins 13 and 25 (bottom row middle, and bottom right-end) are -the I2C clock and I2C data lines, respectively. +5V and GND are probably -also easily available making the addition of extra I2C/SMBus devices easy -to implement. --- linux-2.6.32-pre.orig/drivers/i2c/busses/Kconfig 2009-09-18 22:40:54.000000000 +0200 +++ linux-2.6.32-pre/drivers/i2c/busses/Kconfig 2009-09-18 23:04:23.000000000 +0200 @@ -640,22 +640,6 @@ config I2C_TINY_USB This driver can also be built as a module. If so, the module will be called i2c-tiny-usb. -comment "Graphics adapter I2C/DDC channel drivers" - depends on PCI - -config I2C_VOODOO3 - tristate "Voodoo 3 (DEPRECATED)" - depends on PCI - select I2C_ALGOBIT - help - If you say yes to this option, support will be included for the - Voodoo 3 I2C interface. This driver is deprecated and you should - use the tdfxfb driver instead, which additionally provides - framebuffer support. - - This driver can also be built as a module. If so, the module - will be called i2c-voodoo3. - comment "Other I2C/SMBus bus drivers" config I2C_ACORN --- linux-2.6.32-pre.orig/drivers/i2c/busses/Makefile 2009-09-18 22:40:54.000000000 +0200 +++ linux-2.6.32-pre/drivers/i2c/busses/Makefile 2009-09-18 23:04:16.000000000 +0200 @@ -61,9 +61,6 @@ obj-$(CONFIG_I2C_PARPORT_LIGHT) += i2c-p obj-$(CONFIG_I2C_TAOS_EVM) += i2c-taos-evm.o obj-$(CONFIG_I2C_TINY_USB) += i2c-tiny-usb.o -# Graphics adapter I2C/DDC channel drivers -obj-$(CONFIG_I2C_VOODOO3) += i2c-voodoo3.o - # Other I2C/SMBus bus drivers obj-$(CONFIG_I2C_ACORN) += i2c-acorn.o obj-$(CONFIG_I2C_ELEKTOR) += i2c-elektor.o --- linux-2.6.32-pre.orig/drivers/i2c/busses/i2c-voodoo3.c 2009-09-10 10:08:18.000000000 +0200 +++ /dev/null 1970-01-01 00:00:00.000000000 +0000 @@ -1,248 +0,0 @@ -/* - Copyright (c) 1998, 1999 Frodo Looijaard <frodol@xxxxxx>, - Philip Edelbrock <phil@xxxxxxxxxxxxx>, - Ralph Metzler <rjkm@xxxxxxxxxxxxxxxx>, and - Mark D. Studebaker <mdsxyz123@xxxxxxxxx> - - Based on code written by Ralph Metzler <rjkm@xxxxxxxxxxxxxxxx> and - Simon Vogl - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -*/ - -/* This interfaces to the I2C bus of the Voodoo3 to gain access to - the BT869 and possibly other I2C devices. */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <linux/i2c.h> -#include <linux/i2c-algo-bit.h> -#include <asm/io.h> - -/* the only registers we use */ -#define REG 0x78 -#define REG2 0x70 - -/* bit locations in the register */ -#define DDC_ENAB 0x00040000 -#define DDC_SCL_OUT 0x00080000 -#define DDC_SDA_OUT 0x00100000 -#define DDC_SCL_IN 0x00200000 -#define DDC_SDA_IN 0x00400000 -#define I2C_ENAB 0x00800000 -#define I2C_SCL_OUT 0x01000000 -#define I2C_SDA_OUT 0x02000000 -#define I2C_SCL_IN 0x04000000 -#define I2C_SDA_IN 0x08000000 - -/* initialization states */ -#define INIT2 0x2 -#define INIT3 0x4 - -/* delays */ -#define CYCLE_DELAY 10 -#define TIMEOUT (HZ / 2) - - -static void __iomem *ioaddr; - -/* The voo GPIO registers don't have individual masks for each bit - so we always have to read before writing. */ - -static void bit_vooi2c_setscl(void *data, int val) -{ - unsigned int r; - r = readl(ioaddr + REG); - if (val) - r |= I2C_SCL_OUT; - else - r &= ~I2C_SCL_OUT; - writel(r, ioaddr + REG); - readl(ioaddr + REG); /* flush posted write */ -} - -static void bit_vooi2c_setsda(void *data, int val) -{ - unsigned int r; - r = readl(ioaddr + REG); - if (val) - r |= I2C_SDA_OUT; - else - r &= ~I2C_SDA_OUT; - writel(r, ioaddr + REG); - readl(ioaddr + REG); /* flush posted write */ -} - -/* The GPIO pins are open drain, so the pins always remain outputs. - We rely on the i2c-algo-bit routines to set the pins high before - reading the input from other chips. */ - -static int bit_vooi2c_getscl(void *data) -{ - return (0 != (readl(ioaddr + REG) & I2C_SCL_IN)); -} - -static int bit_vooi2c_getsda(void *data) -{ - return (0 != (readl(ioaddr + REG) & I2C_SDA_IN)); -} - -static void bit_vooddc_setscl(void *data, int val) -{ - unsigned int r; - r = readl(ioaddr + REG); - if (val) - r |= DDC_SCL_OUT; - else - r &= ~DDC_SCL_OUT; - writel(r, ioaddr + REG); - readl(ioaddr + REG); /* flush posted write */ -} - -static void bit_vooddc_setsda(void *data, int val) -{ - unsigned int r; - r = readl(ioaddr + REG); - if (val) - r |= DDC_SDA_OUT; - else - r &= ~DDC_SDA_OUT; - writel(r, ioaddr + REG); - readl(ioaddr + REG); /* flush posted write */ -} - -static int bit_vooddc_getscl(void *data) -{ - return (0 != (readl(ioaddr + REG) & DDC_SCL_IN)); -} - -static int bit_vooddc_getsda(void *data) -{ - return (0 != (readl(ioaddr + REG) & DDC_SDA_IN)); -} - -static int config_v3(struct pci_dev *dev) -{ - unsigned long cadr; - - /* map Voodoo3 memory */ - cadr = dev->resource[0].start; - cadr &= PCI_BASE_ADDRESS_MEM_MASK; - ioaddr = ioremap_nocache(cadr, 0x1000); - if (ioaddr) { - writel(0x8160, ioaddr + REG2); - writel(0xcffc0020, ioaddr + REG); - dev_info(&dev->dev, "Using Banshee/Voodoo3 I2C device at %p\n", ioaddr); - return 0; - } - return -ENODEV; -} - -static struct i2c_algo_bit_data voo_i2c_bit_data = { - .setsda = bit_vooi2c_setsda, - .setscl = bit_vooi2c_setscl, - .getsda = bit_vooi2c_getsda, - .getscl = bit_vooi2c_getscl, - .udelay = CYCLE_DELAY, - .timeout = TIMEOUT -}; - -static struct i2c_adapter voodoo3_i2c_adapter = { - .owner = THIS_MODULE, - .name = "I2C Voodoo3/Banshee adapter", - .algo_data = &voo_i2c_bit_data, -}; - -static struct i2c_algo_bit_data voo_ddc_bit_data = { - .setsda = bit_vooddc_setsda, - .setscl = bit_vooddc_setscl, - .getsda = bit_vooddc_getsda, - .getscl = bit_vooddc_getscl, - .udelay = CYCLE_DELAY, - .timeout = TIMEOUT -}; - -static struct i2c_adapter voodoo3_ddc_adapter = { - .owner = THIS_MODULE, - .class = I2C_CLASS_DDC, - .name = "DDC Voodoo3/Banshee adapter", - .algo_data = &voo_ddc_bit_data, -}; - -static struct pci_device_id voodoo3_ids[] __devinitdata = { - { PCI_DEVICE(PCI_VENDOR_ID_3DFX, PCI_DEVICE_ID_3DFX_VOODOO3) }, - { PCI_DEVICE(PCI_VENDOR_ID_3DFX, PCI_DEVICE_ID_3DFX_BANSHEE) }, - { 0, } -}; - -MODULE_DEVICE_TABLE (pci, voodoo3_ids); - -static int __devinit voodoo3_probe(struct pci_dev *dev, const struct pci_device_id *id) -{ - int retval; - - retval = config_v3(dev); - if (retval) - return retval; - - /* set up the sysfs linkage to our parent device */ - voodoo3_i2c_adapter.dev.parent = &dev->dev; - voodoo3_ddc_adapter.dev.parent = &dev->dev; - - retval = i2c_bit_add_bus(&voodoo3_i2c_adapter); - if (retval) - return retval; - retval = i2c_bit_add_bus(&voodoo3_ddc_adapter); - if (retval) - i2c_del_adapter(&voodoo3_i2c_adapter); - return retval; -} - -static void __devexit voodoo3_remove(struct pci_dev *dev) -{ - i2c_del_adapter(&voodoo3_i2c_adapter); - i2c_del_adapter(&voodoo3_ddc_adapter); - iounmap(ioaddr); -} - -static struct pci_driver voodoo3_driver = { - .name = "voodoo3_smbus", - .id_table = voodoo3_ids, - .probe = voodoo3_probe, - .remove = __devexit_p(voodoo3_remove), -}; - -static int __init i2c_voodoo3_init(void) -{ - return pci_register_driver(&voodoo3_driver); -} - -static void __exit i2c_voodoo3_exit(void) -{ - pci_unregister_driver(&voodoo3_driver); -} - - -MODULE_AUTHOR("Frodo Looijaard <frodol@xxxxxx>, " - "Philip Edelbrock <phil@xxxxxxxxxxxxx>, " - "Ralph Metzler <rjkm@xxxxxxxxxxxxxxxx>, " - "and Mark D. Studebaker <mdsxyz123@xxxxxxxxx>"); -MODULE_DESCRIPTION("Voodoo3 I2C/SMBus driver"); -MODULE_LICENSE("GPL"); - -module_init(i2c_voodoo3_init); -module_exit(i2c_voodoo3_exit); -- Jean Delvare -- To unsubscribe from this list: send the line "unsubscribe linux-i2c" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
