[PATCH] hwmon: (aquacomputer_d5next) Add support for Aquacomputer High Flow Next

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Extend aquacomputer_d5next driver to expose various hardware
sensors of the Aquacomputer High Flow Next flow sensor, which
communicates through a proprietary USB HID protocol.

The High Flow Next exposes +5V voltages, water quality, conductivity
and flow readings. A temperature sensor can be connected to it, in
which case it provides its reading and an estimation of the
dissipated/absorbed power in the liquid cooling loop.

Additionally, serial number and firmware version are exposed through
debugfs.

Registry offsets were discovered and tested by users on Github [1] [2].

[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/8
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/34

Signed-off-by: Aleksa Savic <savicaleksa83@xxxxxxxxx>
---
 Documentation/hwmon/aquacomputer_d5next.rst |  4 +
 drivers/hwmon/Kconfig                       |  6 +-
 drivers/hwmon/aquacomputer_d5next.c         | 88 ++++++++++++++++++++-
 3 files changed, 93 insertions(+), 5 deletions(-)

diff --git a/Documentation/hwmon/aquacomputer_d5next.rst b/Documentation/hwmon/aquacomputer_d5next.rst
index b63a78d47624..3d044b1a9aed 100644
--- a/Documentation/hwmon/aquacomputer_d5next.rst
+++ b/Documentation/hwmon/aquacomputer_d5next.rst
@@ -43,6 +43,10 @@ voltage and current.
 The Farbwerk and Farbwerk 360 expose four temperature sensors. Additionally,
 sixteen virtual temperature sensors of the Farbwerk 360 are exposed.
 
+The High Flow Next exposes +5V voltages, water quality, conductivity and flow readings.
+A temperature sensor can be connected to it, in which case it provides its reading
+and an estimation of the dissipated/absorbed power in the liquid cooling loop.
+
 Depending on the device, not all sysfs and debugfs entries will be available.
 Writing to virtual temperature sensors is not currently supported.
 
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index d32f1705915c..f604f599a341 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -257,14 +257,14 @@ config SENSORS_AHT10
 	  will be called aht10.
 
 config SENSORS_AQUACOMPUTER_D5NEXT
-	tristate "Aquacomputer D5 Next, Octo, Quadro, Farbwerk, and Farbwerk 360"
+	tristate "Aquacomputer D5 Next, Octo, Quadro, Farbwerk, Farbwerk 360, High Flow Next"
 	depends on USB_HID
 	select CRC16
 	help
 	  If you say yes here you get support for sensors and fans of
 	  the Aquacomputer D5 Next watercooling pump, Octo and Quadro fan
-	  controllers, Farbwerk and Farbwerk 360 RGB controllers, where
-	  available.
+	  controllers, Farbwerk and Farbwerk 360 RGB controllers, High Flow
+	  Next sensor, where available.
 
 	  This driver can also be built as a module. If so, the module
 	  will be called aquacomputer_d5next.
diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
index b2b0c4fdfa84..a715142a3d0c 100644
--- a/drivers/hwmon/aquacomputer_d5next.c
+++ b/drivers/hwmon/aquacomputer_d5next.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
  * hwmon driver for Aquacomputer devices (D5 Next, Farbwerk, Farbwerk 360, Octo,
- * Quadro)
+ * Quadro, High Flow Next)
  *
  * Aquacomputer devices send HID reports (with ID 0x01) every second to report
  * sensor values.
@@ -34,7 +34,8 @@ static const char *const aqc_device_names[] = {
 	[farbwerk] = "farbwerk",
 	[farbwerk360] = "farbwerk360",
 	[octo] = "octo",
-	[quadro] = "quadro"
+	[quadro] = "quadro",
+	[highflownext] = "highflownext"
 };
 
 #define DRIVER_NAME			"aquacomputer_d5next"
@@ -120,6 +121,16 @@ static u8 quadro_sensor_fan_offsets[] = { 0x70, 0x7D, 0x8A, 0x97 };
 /* Fan speed registers in Quadro control report (from 0-100%) */
 static u16 quadro_ctrl_fan_offsets[] = { 0x36, 0x8b, 0xe0, 0x135 };
 
+/* Register offsets for the High Flow Next */
+#define HIGHFLOWNEXT_NUM_SENSORS	2
+#define HIGHFLOWNEXT_SENSOR_START	85
+#define HIGHFLOWNEXT_FLOW		81
+#define HIGHFLOWNEXT_WATER_QUALITY	89
+#define HIGHFLOWNEXT_POWER		91
+#define HIGHFLOWNEXT_CONDUCTIVITY	95
+#define HIGHFLOWNEXT_5V_VOLTAGE		97
+#define HIGHFLOWNEXT_5V_VOLTAGE_USB	99
+
 /* Labels for D5 Next */
 static const char *const label_d5next_temp[] = {
 	"Coolant temp"
@@ -228,6 +239,27 @@ static const char *const label_quadro_speeds[] = {
 	"Flow speed [dL/h]"
 };
 
+/* Labels for High Flow Next */
+static const char *const label_highflownext_temp_sensors[] = {
+	"Coolant temp",
+	"External sensor"
+};
+
+static const char *const label_highflownext_fan_speed[] = {
+	"Flow [dL/h]",
+	"Water quality [%]",
+	"Conductivity [nS/cm]",
+};
+
+static const char *const label_highflownext_power[] = {
+	"Dissipated power",
+};
+
+static const char *const label_highflownext_voltage[] = {
+	"+5V voltage",
+	"+5V USB voltage"
+};
+
 struct aqc_data {
 	struct hid_device *hdev;
 	struct device *hwmon_dev;
@@ -390,6 +422,11 @@ static umode_t aqc_is_visible(const void *data, enum hwmon_sensor_types type, u3
 		break;
 	case hwmon_fan:
 		switch (priv->kind) {
+		case highflownext:
+			/* Special case to support flow sensor, water quality and conductivity */
+			if (channel < 3)
+				return 0444;
+			break;
 		case quadro:
 			/* Special case to support flow sensor */
 			if (channel < priv->num_fans + 1)
@@ -402,6 +439,18 @@ static umode_t aqc_is_visible(const void *data, enum hwmon_sensor_types type, u3
 		}
 		break;
 	case hwmon_power:
+		switch (priv->kind) {
+		case highflownext:
+			/* Special case to support one power sensor */
+			if (channel == 0)
+				return 0444;
+			break;
+		default:
+			if (channel < priv->num_fans)
+				return 0444;
+			break;
+		}
+		break;
 	case hwmon_curr:
 		if (channel < priv->num_fans)
 			return 0444;
@@ -413,6 +462,11 @@ static umode_t aqc_is_visible(const void *data, enum hwmon_sensor_types type, u3
 			if (channel < priv->num_fans + 2)
 				return 0444;
 			break;
+		case highflownext:
+			/* Special case to support two voltage sensors */
+			if (channel < 2)
+				return 0444;
+			break;
 		default:
 			if (channel < priv->num_fans)
 				return 0444;
@@ -679,6 +733,22 @@ static int aqc_raw_event(struct hid_device *hdev, struct hid_report *report, u8
 	case quadro:
 		priv->speed_input[4] = get_unaligned_be16(data + priv->flow_sensor_offset);
 		break;
+	case highflownext:
+		/* If external temp sensor is not connected, its power reading is also N/A */
+		if (priv->temp_input[1] == -ENODATA)
+			priv->power_input[0] = -ENODATA;
+		else
+			priv->power_input[0] =
+			    get_unaligned_be16(data + HIGHFLOWNEXT_POWER) * 1000000;
+
+		priv->voltage_input[0] = get_unaligned_be16(data + HIGHFLOWNEXT_5V_VOLTAGE) * 10;
+		priv->voltage_input[1] =
+		    get_unaligned_be16(data + HIGHFLOWNEXT_5V_VOLTAGE_USB) * 10;
+
+		priv->speed_input[0] = get_unaligned_be16(data + HIGHFLOWNEXT_FLOW);
+		priv->speed_input[1] = get_unaligned_be16(data + HIGHFLOWNEXT_WATER_QUALITY);
+		priv->speed_input[2] = get_unaligned_be16(data + HIGHFLOWNEXT_CONDUCTIVITY);
+		break;
 	default:
 		break;
 	}
@@ -851,6 +921,19 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
 		priv->voltage_label = label_fan_voltage;
 		priv->current_label = label_fan_current;
 		break;
+	case USB_PRODUCT_ID_HIGHFLOWNEXT:
+		priv->kind = highflownext;
+
+		priv->num_fans = 0;
+		priv->num_temp_sensors = HIGHFLOWNEXT_NUM_SENSORS;
+		priv->temp_sensor_start_offset = HIGHFLOWNEXT_SENSOR_START;
+		priv->power_cycle_count_offset = QUADRO_POWER_CYCLES;
+
+		priv->temp_label = label_highflownext_temp_sensors;
+		priv->speed_label = label_highflownext_fan_speed;
+		priv->power_label = label_highflownext_power;
+		priv->voltage_label = label_highflownext_voltage;
+		break;
 	default:
 		break;
 	}
@@ -907,6 +990,7 @@ static const struct hid_device_id aqc_table[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_FARBWERK360) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_OCTO) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_QUADRO) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_HIGHFLOWNEXT) },
 	{ }
 };
 
-- 
2.37.2




[Index of Archives]     [LM Sensors]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux