On 5/3/21 1:46 PM, Vadim Pasternak wrote:
> Add support for mp2888 device from Monolithic Power Systems, Inc. (MPS)
> vendor. This is a digital, multi-phase, pulse-width modulation
> controller.
>
> This device supports:
> - One power rail.
> - Programmable Multi-Phase up to 10 Phases.
> - PWM-VID Interface
> - One pages 0 for telemetry.
> - Programmable pins for PMBus Address.
> - Built-In EEPROM to Store Custom Configurations.
> - Can configured VOUT readout in direct or VID format and allows
> setting of different formats on rails 1 and 2. For VID the following
> protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
> 10-mV DAC, IMVP9 mode with 5-mV DAC.
>
> Signed-off-by: Vadim Pasternak <vadimp@xxxxxxxxxx>
> ---
> v3->v4
> Comments pointed out by Guenter:
> - Fix PMBUS_READ_VIN and limits calculations.
> - Add comment for PMBUS_OT_WARN_LIMIT scaling.
> - Fix PMBUS_READ_IOUT, PMBUS_READ_POUT, PMBUS_READ_PIN calculations.
> - Enable PMBUS_IOUT_OC_WARN_LIMIT and PMBUS_POUT_OP_WARN_LIMIT.
> Fixes from Vadim:
> - Disable PMBUS_POUT_MAX. Device uses this register for different
> purpose.
> - Disable PMBUS_MFR_VOU_MIN. Device doe not implement this register.
> - Update documentation file.
>
> v2->v3
> Comments pointed out by Guenter:
> - Fix precision for PMBUS_READ_VIN (it requires adding scale for
> PMBUS_VIN_OV_FAULT_LIMIT and PMBUS_VIN_UV_WARN_LIMIT.
> - Fix precision for PMBUS_READ_TEMPERATURE_1 (it requires adding
> scale for PMBUS_OT_WARN_LIMIT).
> - Use DIV_ROUND_CLOSEST_ULL for scaling PMBUS_READ_POUT,
> PMBUS_READ_PIN readouts.
> Notes and fixes from Vadim:
> - READ_IOUT in linear11 does not give write calculation (tested with
> external load), while in direct format readouts are correct.
> - Disable non-configured phases in mp2888_identify_multiphase().
>
> v1->v2:
> Comments pointed out by Guenter:
> - Use standard access for getting PMBUS_OT_WARN_LIMIT,
> PMBUS_VIN_OV_FAULT_LIMIT, PMBUS_VIN_UV_WARN_LIMIT.
> - Use linear11 conversion for PMBUS_READ_VIN, PMBUS_READ_POUT,
> PMBUS_READ_PIN, PMBUS_READ_TEMPERATURE_1 and adjust coefficients.
> - Add reading phases current from the dedicated registers.
> - Add comment for not implemented or implemented not according to the
> spec registers, for which "ENXIO" code is returned.
> - Set PMBUS_HAVE_IOUT" statically.
> Notes from Vadim:
> - READ_IOUT uses direct format, so I did not adjust it like the below
> registers.
> ---
> Documentation/hwmon/mp2888.rst | 113 +++++++++++++
> drivers/hwmon/pmbus/Kconfig | 9 +
> drivers/hwmon/pmbus/Makefile | 1 +
> drivers/hwmon/pmbus/mp2888.c | 366 +++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 489 insertions(+)
> create mode 100644 Documentation/hwmon/mp2888.rst
> create mode 100644 drivers/hwmon/pmbus/mp2888.c
>
> diff --git a/Documentation/hwmon/mp2888.rst b/Documentation/hwmon/mp2888.rst
> new file mode 100644
> index 000000000000..5e578fd7b147
> --- /dev/null
> +++ b/Documentation/hwmon/mp2888.rst
> @@ -0,0 +1,113 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +Kernel driver mp2888
> +====================
> +
> +Supported chips:
> +
> + * MPS MP12254
> +
> + Prefix: 'mp2888'
> +
> +Author:
> +
> + Vadim Pasternak <vadimp@xxxxxxxxxx>
> +
> +Description
> +-----------
> +
> +This driver implements support for Monolithic Power Systems, Inc. (MPS)
> +vendor dual-loop, digital, multi-phase controller MP2888.
> +
> +This device: supports:
> +
> +- One power rail.
> +- Programmable Multi-Phase up to 10 Phases.
> +- PWM-VID Interface
> +- One pages 0 for telemetry.
> +- Programmable pins for PMBus Address.
> +- Built-In EEPROM to Store Custom Configurations.
> +
> +Device complaint with:
> +
> +- PMBus rev 1.3 interface.
> +
> +Device supports direct format for reading output current, output voltage,
> +input and output power and temperature.
> +Device supports linear format for reading input voltage and input power.
> +
> +The driver provides the next attributes for the current:
> +
> +- for current out input and maximum alarm;
> +- for phase current: input and label.
> +
> +The driver exports the following attributes via the 'sysfs' files, where:
> +
> +- 'n' is number of configured phases (from 1 to 10);
> +- index 1 for "iout";
> +- indexes 2 ... 1 + n for phases.
> +
> +**curr[1-{1+n}]_input**
> +
> +**curr[1-{1+n}]_label**
> +
> +**curr1_max**
> +
> +**curr1_max_alarm**
> +
> +The driver provides the next attributes for the voltage:
> +
> +- for voltage in: input, low and high critical thresholds, low and high
> + critical alarms;
> +- for voltage out: input and high alarm;
> +
> +The driver exports the following attributes via the 'sysfs' files, where
> +
> +**in1_crit**
> +
> +**in1_crit_alarm**
> +
> +**in1_input**
> +
> +**in1_label**
> +
> +**in1_min**
> +
> +**in1_min_alarm**
> +
> +**in2_alarm**
> +
> +**in2_input**
> +
> +**in2_label**
> +
> +The driver provides the next attributes for the power:
> +
> +- for power in alarm and input.
> +- for power out: cap, cap alarm an input.
> +
> +The driver exports the following attributes via the 'sysfs' files, where
> +- indexes 1 for "pin";
> +- indexes 2 for "pout";
> +
> +**power1_alarm**
> +
> +**power1_input**
> +
> +**power1_label**
> +
> +**power2_input**
> +
> +**power2_label**
> +
> +**power2_max**
> +
> +**power2_max_alarm**
> +
> +The driver provides the next attributes for the temperature:
> +
> +**temp1_input**
> +
> +**temp1_max**
> +
> +**temp1_max_alarm**
> diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> index 32d2fc850621..a57571928b31 100644
> --- a/drivers/hwmon/pmbus/Kconfig
> +++ b/drivers/hwmon/pmbus/Kconfig
> @@ -211,6 +211,15 @@ config SENSORS_MAX8688
> This driver can also be built as a module. If so, the module will
> be called max8688.
>
> +config SENSORS_MP2888
> + tristate "MPS MP2888"
> + help
> + If you say yes here you get hardware monitoring support for MPS
> + MP2888 Digital, Multi-Phase, Pulse-Width Modulation Controller.
> +
> + This driver can also be built as a module. If so, the module will
> + be called mp2888.
> +
> config SENSORS_MP2975
> tristate "MPS MP2975"
> help
> diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> index 6a4ba0fdc1db..a6d7352621ca 100644
> --- a/drivers/hwmon/pmbus/Makefile
> +++ b/drivers/hwmon/pmbus/Makefile
> @@ -24,6 +24,7 @@ obj-$(CONFIG_SENSORS_MAX20751) += max20751.o
> obj-$(CONFIG_SENSORS_MAX31785) += max31785.o
> obj-$(CONFIG_SENSORS_MAX34440) += max34440.o
> obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
> +obj-$(CONFIG_SENSORS_MP2888) += mp2888.o
> obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
> obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
> obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o
> diff --git a/drivers/hwmon/pmbus/mp2888.c b/drivers/hwmon/pmbus/mp2888.c
> new file mode 100644
> index 000000000000..393221d25379
> --- /dev/null
> +++ b/drivers/hwmon/pmbus/mp2888.c
> @@ -0,0 +1,366 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Hardware monitoring driver for MPS Multi-phase Digital VR Controllers
> + *
> + * Copyright (C) 2020 Nvidia Technologies Ltd.
> + */
> +
> +#include <linux/err.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include "pmbus.h"
> +
> +/* Vendor specific registers. */
> +#define MP2888_MFR_SYS_CONFIG 0x44
> +#define MP2888_MFR_READ_CS1_2 0x73
> +#define MP2888_MFR_READ_CS3_4 0x74
> +#define MP2888_MFR_READ_CS5_6 0x75
> +#define MP2888_MFR_READ_CS7_8 0x76
> +#define MP2888_MFR_READ_CS9_10 0x77
> +#define MP2888_MFR_VR_CONFIG1 0xe1
> +
> +#define MP2888_TOTAL_CURRENT_RESOLUTION BIT(3)
> +#define MP2888_PHASE_CURRENT_RESOLUTION BIT(4)
> +#define MP2888_DRMOS_KCS GENMASK(2, 0)
> +#define MP2888_TEMP_UNIT 10
> +#define MP2888_MAX_PHASE 10
> +
> +struct mp2888_data {
> + struct pmbus_driver_info info;
> + int total_curr_resolution;
> + int phase_curr_resolution;
> + int curr_sense_gain;
> +};
> +
> +#define to_mp2888_data(x) container_of(x, struct mp2888_data, info)
> +
> +static int mp2888_read_byte_data(struct i2c_client *client, int page, int reg)
> +{
> + switch (reg) {
> + case PMBUS_VOUT_MODE:
> + /* Enforce VOUT direct format. */
> + return PB_VOUT_MODE_DIRECT;
> + default:
> + return -ENODATA;
> + }
> +}
> +
> +static int
> +mp2888_current_sense_gain_and_resolution_get(struct i2c_client *client, struct mp2888_data *data)
> +{
> + int ret;
> +
> + /*
> + * Obtain DrMOS current sense gain of power stage from the register
> + * , bits 0-2. The value is selected as below:
> + * 00b - 5µA/A, 01b - 8.5µA/A, 10b - 9.7µA/A, 11b - 10µA/A. Other
> + * values are reserved.
> + */
> + ret = i2c_smbus_read_word_data(client, MP2888_MFR_SYS_CONFIG);
> + if (ret < 0)
> + return ret;
> +
> + switch (ret & MP2888_DRMOS_KCS) {
> + case 0:
> + data->curr_sense_gain = 85;
> + break;
> + case 1:
> + data->curr_sense_gain = 97;
> + break;
> + case 2:
> + data->curr_sense_gain = 100;
> + break;
> + case 3:
> + data->curr_sense_gain = 50;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + /*
> + * Obtain resolution selector for total and phase current report and protection.
> + * 0: original resolution; 1: half resolution (in such case phase current value should
> + * be doubled.
> + */
> + data->total_curr_resolution = (ret & MP2888_TOTAL_CURRENT_RESOLUTION) >> 3;
> + data->phase_curr_resolution = (ret & MP2888_PHASE_CURRENT_RESOLUTION) >> 4;
> +
> + return 0;
> +}
> +
> +static int
> +mp2888_read_phase(struct i2c_client *client, struct mp2888_data *data, int page, int phase, u8 reg)
> +{
> + int ret;
> +
> + ret = pmbus_read_word_data(client, page, phase, reg);
> + if (ret < 0)
> + return ret;
> +
> + if (!((phase + 1) % 2))
> + ret >>= 8;
> + ret &= 0xff;
> +
> + /*
> + * Output value is calculated as: (READ_CSx / 80 – 1.23) / (Kcs * Rcs)
> + * where:
> + * - Kcs is the DrMOS current sense gain of power stage, which is obtained from the
> + * register MP2888_MFR_VR_CONFIG1, bits 13-12 with the following selection of DrMOS
> + * (data->curr_sense_gain):
> + * 00b - 5µA/A, 01b - 8.5µA/A, 10b - 9.7µA/A, 11b - 10µA/A.
> + * - Rcs is the internal phase current sense resistor. This parameter depends on hardware
> + * assembly. By default it is set to 1kΩ. In case of different assembly, user should
> + * scale this parameter by dividing it by Rcs.
> + * If phase current resolution bit is set to 1, READ_CSx value should be doubled.
> + * Note, that current phase sensing, providing by the device is not accurate. This is
> + * because sampling of current occurrence of bit weight has a big deviation, especially for
> + * light load.
> + */
> + ret = DIV_ROUND_CLOSEST(ret * 100 - 9800, data->curr_sense_gain);
> + if (data->phase_curr_resolution)
> + ret *= 2;
> + /* Scale according to total current resolution. */
> + if (data->total_curr_resolution)
> + ret *= 2;
> + else
> + ret *= 4;
> + return ret;
> +}
> +
> +static int
> +mp2888_read_phases(struct i2c_client *client, struct mp2888_data *data, int page, int phase)
> +{
> + int ret;
> +
> + switch (phase) {
> + case 0 ... 1:
> + ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS1_2);
> + break;
> + case 2 ... 3:
> + ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS3_4);
> + break;
> + case 4 ... 5:
> + ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS5_6);
> + break;
> + case 6 ... 7:
> + ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS7_8);
> + break;
> + case 8 ... 9:
> + ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS9_10);
> + break;
> + default:
> + return -ENODATA;
> + }
> + return ret;
> +}
> +
> +static int mp2888_read_word_data(struct i2c_client *client, int page, int phase, int reg)
> +{
> + const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
> + struct mp2888_data *data = to_mp2888_data(info);
> + int ret;
> +
> + switch (reg) {
> + case PMBUS_READ_VIN:
> + ret = pmbus_read_word_data(client, page, phase, reg);
> + if (ret <= 0)
> + return ret;
> +
> + /*
> + * READ_VIN requires fixup to scale it to linear11 format. Register data format
> + * provides 10 bits for mantissa and 6 bits for exponent. Bits 15:10 are set with
> + * the fixed value 111011b.
> + */
> + ret = ((ret & 0x3ff) >> 1) | (ret & ~GENMASK(11, 0));
That results in a loss of resolution. I think you'll want something like
ret = (ret & GENMASK(9, 0)) | ((ret & GENMASK(31, 10)) << 1);
though I am not sure about the bit numbers.
> + break;
> + case PMBUS_OT_WARN_LIMIT:
> + ret = pmbus_read_word_data(client, page, phase, reg);
> + if (ret < 0)
> + return ret;
> + /*
> + * Chip reports limits in degrees C, but the actual temperature in 10th of
> + * degrees C - scaling is needed to match both.
> + */
> + ret *= MP2888_TEMP_UNIT;
> + break;
> + case PMBUS_READ_IOUT:
> + case PMBUS_IOUT_OC_WARN_LIMIT:
> + if (phase != 0xff)
> + return mp2888_read_phases(client, data, page, phase);
> +
> + ret = pmbus_read_word_data(client, page, phase, reg);
> + if (ret < 0)
> + return ret;
> + /*
> + * READ_IOUT register has unused bits 15:12 with fixed value 1110b. Clear these
> + * bits and scale with total current resolution. Data is provided in direct format.
> + */
> + ret &= GENMASK(11, 0);
> + break;
> + case PMBUS_READ_POUT:
> + case PMBUS_READ_PIN:
> + case PMBUS_POUT_OP_WARN_LIMIT:
> + ret = pmbus_read_word_data(client, page, phase, reg);
> + if (ret < 0)
> + return ret;
> + ret = data->total_curr_resolution ? ret * 2 : ret;
> + break;
> + /*
> + * The below registers are not implemented by device or implemented not according to the
> + * spec. Skip all of them to avoid exposing non-relevant inputs to sysfs.
> + */
> + case PMBUS_OT_FAULT_LIMIT:
> + case PMBUS_UT_WARN_LIMIT:
> + case PMBUS_UT_FAULT_LIMIT:
> + case PMBUS_VIN_UV_FAULT_LIMIT:
> + case PMBUS_VOUT_UV_WARN_LIMIT:
> + case PMBUS_VOUT_OV_WARN_LIMIT:
> + case PMBUS_VOUT_UV_FAULT_LIMIT:
> + case PMBUS_VOUT_OV_FAULT_LIMIT:
> + case PMBUS_VIN_OV_WARN_LIMIT:
> + case PMBUS_IOUT_OC_LV_FAULT_LIMIT:
> + case PMBUS_IOUT_OC_FAULT_LIMIT:
> + case PMBUS_POUT_MAX:
> + case PMBUS_IOUT_UC_FAULT_LIMIT:
> + case PMBUS_POUT_OP_FAULT_LIMIT:
> + case PMBUS_PIN_OP_WARN_LIMIT:
> + case PMBUS_MFR_VIN_MIN:
> + case PMBUS_MFR_VOUT_MIN:
> + case PMBUS_MFR_VIN_MAX:
> + case PMBUS_MFR_VOUT_MAX:
> + case PMBUS_MFR_IIN_MAX:
> + case PMBUS_MFR_IOUT_MAX:
> + case PMBUS_MFR_PIN_MAX:
> + case PMBUS_MFR_POUT_MAX:
> + case PMBUS_MFR_MAX_TEMP_1:
> + return -ENXIO;
> + default:
> + return -ENODATA;
> + }
> +
> + return ret;
> +}
> +
> +static int
> +mp2888_identify_multiphase(struct i2c_client *client, struct mp2888_data *data,
> + struct pmbus_driver_info *info)
> +{
> + int i, ret;
> +
> + ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 0);
> + if (ret < 0)
> + return ret;
> +
> + /* Identify multiphase number - could be from 1 to 10. */
> + ret = i2c_smbus_read_word_data(client, MP2888_MFR_VR_CONFIG1);
> + if (ret <= 0)
> + return ret;
> +
> + info->phases[0] = ret & GENMASK(3, 0);
> +
> + /*
> + * The device provides a total of 10 PWM pins, and can be configured to different phase
> + * count applications for rail.
> + */
> + if (info->phases[0] > MP2888_MAX_PHASE)
> + return -EINVAL;
> +
> + /* Disable non-configured phases. */
> + for (i = info->phases[0]; i < MP2888_MAX_PHASE; i++)
> + info->pfunc[i] = 0;
> +
> + return 0;
> +}
> +
> +static struct pmbus_driver_info mp2888_info = {
> + .pages = 1,
> + .format[PSC_VOLTAGE_IN] = linear,
> + .format[PSC_VOLTAGE_OUT] = direct,
> + .format[PSC_TEMPERATURE] = direct,
> + .format[PSC_CURRENT_IN] = linear,
> + .format[PSC_CURRENT_OUT] = direct,
> + .format[PSC_POWER] = direct,
> + .m[PSC_TEMPERATURE] = 1,
> + .R[PSC_TEMPERATURE] = 1,
> + .m[PSC_VOLTAGE_OUT] = 1,
> + .R[PSC_VOLTAGE_OUT] = 3,
> + .m[PSC_CURRENT_OUT] = 4,
> + .m[PSC_POWER] = 1,
> + .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | PMBUS_HAVE_IOUT |
> + PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
> + PMBUS_HAVE_POUT | PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT |
> + PMBUS_PHASE_VIRTUAL,
> + .pfunc[0] = PMBUS_HAVE_IOUT,
> + .pfunc[1] = PMBUS_HAVE_IOUT,
> + .pfunc[2] = PMBUS_HAVE_IOUT,
> + .pfunc[3] = PMBUS_HAVE_IOUT,
> + .pfunc[4] = PMBUS_HAVE_IOUT,
> + .pfunc[5] = PMBUS_HAVE_IOUT,
> + .pfunc[6] = PMBUS_HAVE_IOUT,
> + .pfunc[7] = PMBUS_HAVE_IOUT,
> + .pfunc[8] = PMBUS_HAVE_IOUT,
> + .pfunc[9] = PMBUS_HAVE_IOUT,
> + .read_byte_data = mp2888_read_byte_data,
> + .read_word_data = mp2888_read_word_data,
Still no write_word_data function, meaning limit writes are quite likely
going to be wrong.
Thanks,
Guenter
> +};
> +
> +static int mp2888_probe(struct i2c_client *client)
> +{
> + struct pmbus_driver_info *info;
> + struct mp2888_data *data;
> + int ret;
> +
> + data = devm_kzalloc(&client->dev, sizeof(struct mp2888_data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + memcpy(&data->info, &mp2888_info, sizeof(*info));
> + info = &data->info;
> +
> + /* Identify multiphase configuration. */
> + ret = mp2888_identify_multiphase(client, data, info);
> + if (ret)
> + return ret;
> +
> + /* Obtain current sense gain of power stage and current resolution. */
> + ret = mp2888_current_sense_gain_and_resolution_get(client, data);
> + if (ret)
> + return ret;
> +
> + if (data->total_curr_resolution) {
> + info->m[PSC_POWER] *= 2;
> + info->m[PSC_CURRENT_OUT] /= 2;
> + }
> +
> + return pmbus_do_probe(client, info);
> +}
> +
> +static const struct i2c_device_id mp2888_id[] = {
> + {"mp2888", 0},
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, mp2888_id);
> +
> +static const struct of_device_id __maybe_unused mp2888_of_match[] = {
> + {.compatible = "mps,mp2888"},
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, mp2888_of_match);
> +
> +static struct i2c_driver mp2888_driver = {
> + .driver = {
> + .name = "mp2888",
> + .of_match_table = of_match_ptr(mp2888_of_match),
> + },
> + .probe_new = mp2888_probe,
> + .id_table = mp2888_id,
> +};
> +
> +module_i2c_driver(mp2888_driver);
> +
> +MODULE_AUTHOR("Vadim Pasternak <vadimp@xxxxxxxxxx>");
> +MODULE_DESCRIPTION("PMBus driver for MPS MP2888 device");
> +MODULE_LICENSE("GPL");
>
