[PATCH hwmon-next v4 2/3] hwmon: (pmbus) Add support for MPS Multi-phase mp2888 controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add support for mp2888 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a digital, multi-phase, pulse-width modulation
controller.

This device supports:
- One power rail.
- Programmable Multi-Phase up to 10 Phases.
- PWM-VID Interface
- One pages 0 for telemetry.
- Programmable pins for PMBus Address.
- Built-In EEPROM to Store Custom Configurations.
- Can configured VOUT readout in direct or VID format and allows
  setting of different formats on rails 1 and 2. For VID the following
  protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
  10-mV DAC, IMVP9 mode with 5-mV DAC.

Signed-off-by: Vadim Pasternak <vadimp@xxxxxxxxxx>
---
v3->v4
 Comments pointed out by Guenter:
  - Fix PMBUS_READ_VIN and limits calculations.
  - Add comment for PMBUS_OT_WARN_LIMIT scaling.
  - Fix PMBUS_READ_IOUT, PMBUS_READ_POUT, PMBUS_READ_PIN calculations.
  - Enable PMBUS_IOUT_OC_WARN_LIMIT and PMBUS_POUT_OP_WARN_LIMIT.
 Fixes from Vadim:
  - Disable PMBUS_POUT_MAX. Device uses this register for different
    purpose.
  - Disable PMBUS_MFR_VOU_MIN. Device doe not implement this register.
  - Update documentation file.

v2->v3
 Comments pointed out by Guenter:
 - Fix precision for PMBUS_READ_VIN (it requires adding scale for
   PMBUS_VIN_OV_FAULT_LIMIT and PMBUS_VIN_UV_WARN_LIMIT.
 - Fix precision for PMBUS_READ_TEMPERATURE_1 (it requires adding
   scale for PMBUS_OT_WARN_LIMIT).
 - Use DIV_ROUND_CLOSEST_ULL for scaling PMBUS_READ_POUT,
   PMBUS_READ_PIN readouts.
 Notes and fixes from Vadim:
  - READ_IOUT in linear11 does not give write calculation (tested with
    external load), while in direct format readouts are correct.
  - Disable non-configured phases in mp2888_identify_multiphase().

v1->v2:
 Comments pointed out by Guenter:
  - Use standard access for getting PMBUS_OT_WARN_LIMIT,
    PMBUS_VIN_OV_FAULT_LIMIT, PMBUS_VIN_UV_WARN_LIMIT.
  - Use linear11 conversion for PMBUS_READ_VIN, PMBUS_READ_POUT,
    PMBUS_READ_PIN, PMBUS_READ_TEMPERATURE_1 and adjust coefficients.
  - Add reading phases current from the dedicated registers.
  - Add comment for not implemented or implemented not according to the
	spec registers, for which "ENXIO" code is returned.
  - Set PMBUS_HAVE_IOUT" statically.
  Notes from Vadim:
  - READ_IOUT uses direct format, so I did not adjust it like the below
    registers.
---
 Documentation/hwmon/mp2888.rst | 113 +++++++++++++
 drivers/hwmon/pmbus/Kconfig    |   9 +
 drivers/hwmon/pmbus/Makefile   |   1 +
 drivers/hwmon/pmbus/mp2888.c   | 366 +++++++++++++++++++++++++++++++++++++++++
 4 files changed, 489 insertions(+)
 create mode 100644 Documentation/hwmon/mp2888.rst
 create mode 100644 drivers/hwmon/pmbus/mp2888.c

diff --git a/Documentation/hwmon/mp2888.rst b/Documentation/hwmon/mp2888.rst
new file mode 100644
index 000000000000..5e578fd7b147
--- /dev/null
+++ b/Documentation/hwmon/mp2888.rst
@@ -0,0 +1,113 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver mp2888
+====================
+
+Supported chips:
+
+  * MPS MP12254
+
+    Prefix: 'mp2888'
+
+Author:
+
+	Vadim Pasternak <vadimp@xxxxxxxxxx>
+
+Description
+-----------
+
+This driver implements support for Monolithic Power Systems, Inc. (MPS)
+vendor dual-loop, digital, multi-phase controller MP2888.
+
+This device: supports:
+
+- One power rail.
+- Programmable Multi-Phase up to 10 Phases.
+- PWM-VID Interface
+- One pages 0 for telemetry.
+- Programmable pins for PMBus Address.
+- Built-In EEPROM to Store Custom Configurations.
+
+Device complaint with:
+
+- PMBus rev 1.3 interface.
+
+Device supports direct format for reading output current, output voltage,
+input and output power and temperature.
+Device supports linear format for reading input voltage and input power.
+
+The driver provides the next attributes for the current:
+
+- for current out input and maximum alarm;
+- for phase current: input and label.
+
+The driver exports the following attributes via the 'sysfs' files, where:
+
+- 'n' is number of configured phases (from 1 to 10);
+- index 1 for "iout";
+- indexes 2 ... 1 + n for phases.
+
+**curr[1-{1+n}]_input**
+
+**curr[1-{1+n}]_label**
+
+**curr1_max**
+
+**curr1_max_alarm**
+
+The driver provides the next attributes for the voltage:
+
+- for voltage in: input, low and high critical thresholds, low and high
+  critical alarms;
+- for voltage out: input and high alarm;
+
+The driver exports the following attributes via the 'sysfs' files, where
+
+**in1_crit**
+
+**in1_crit_alarm**
+
+**in1_input**
+
+**in1_label**
+
+**in1_min**
+
+**in1_min_alarm**
+
+**in2_alarm**
+
+**in2_input**
+
+**in2_label**
+
+The driver provides the next attributes for the power:
+
+- for power in alarm and input.
+- for power out: cap, cap alarm an input.
+
+The driver exports the following attributes via the 'sysfs' files, where
+- indexes 1 for "pin";
+- indexes 2 for "pout";
+
+**power1_alarm**
+
+**power1_input**
+
+**power1_label**
+
+**power2_input**
+
+**power2_label**
+
+**power2_max**
+
+**power2_max_alarm**
+
+The driver provides the next attributes for the temperature:
+
+**temp1_input**
+
+**temp1_max**
+
+**temp1_max_alarm**
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index 32d2fc850621..a57571928b31 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -211,6 +211,15 @@ config SENSORS_MAX8688
 	  This driver can also be built as a module. If so, the module will
 	  be called max8688.
 
+config SENSORS_MP2888
+	tristate "MPS MP2888"
+	help
+	  If you say yes here you get hardware monitoring support for MPS
+	  MP2888 Digital, Multi-Phase, Pulse-Width Modulation Controller.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called mp2888.
+
 config SENSORS_MP2975
 	tristate "MPS MP2975"
 	help
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index 6a4ba0fdc1db..a6d7352621ca 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_SENSORS_MAX20751)	+= max20751.o
 obj-$(CONFIG_SENSORS_MAX31785)	+= max31785.o
 obj-$(CONFIG_SENSORS_MAX34440)	+= max34440.o
 obj-$(CONFIG_SENSORS_MAX8688)	+= max8688.o
+obj-$(CONFIG_SENSORS_MP2888)	+= mp2888.o
 obj-$(CONFIG_SENSORS_MP2975)	+= mp2975.o
 obj-$(CONFIG_SENSORS_PM6764TR)	+= pm6764tr.o
 obj-$(CONFIG_SENSORS_PXE1610)	+= pxe1610.o
diff --git a/drivers/hwmon/pmbus/mp2888.c b/drivers/hwmon/pmbus/mp2888.c
new file mode 100644
index 000000000000..393221d25379
--- /dev/null
+++ b/drivers/hwmon/pmbus/mp2888.c
@@ -0,0 +1,366 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Hardware monitoring driver for MPS Multi-phase Digital VR Controllers
+ *
+ * Copyright (C) 2020 Nvidia Technologies Ltd.
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include "pmbus.h"
+
+/* Vendor specific registers. */
+#define MP2888_MFR_SYS_CONFIG	0x44
+#define MP2888_MFR_READ_CS1_2	0x73
+#define MP2888_MFR_READ_CS3_4	0x74
+#define MP2888_MFR_READ_CS5_6	0x75
+#define MP2888_MFR_READ_CS7_8	0x76
+#define MP2888_MFR_READ_CS9_10	0x77
+#define MP2888_MFR_VR_CONFIG1	0xe1
+
+#define MP2888_TOTAL_CURRENT_RESOLUTION	BIT(3)
+#define MP2888_PHASE_CURRENT_RESOLUTION	BIT(4)
+#define MP2888_DRMOS_KCS		GENMASK(2, 0)
+#define MP2888_TEMP_UNIT		10
+#define MP2888_MAX_PHASE		10
+
+struct mp2888_data {
+	struct pmbus_driver_info info;
+	int total_curr_resolution;
+	int phase_curr_resolution;
+	int curr_sense_gain;
+};
+
+#define to_mp2888_data(x)  container_of(x, struct mp2888_data, info)
+
+static int mp2888_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+	switch (reg) {
+	case PMBUS_VOUT_MODE:
+		/* Enforce VOUT direct format. */
+		return PB_VOUT_MODE_DIRECT;
+	default:
+		return -ENODATA;
+	}
+}
+
+static int
+mp2888_current_sense_gain_and_resolution_get(struct i2c_client *client, struct mp2888_data *data)
+{
+	int ret;
+
+	/*
+	 * Obtain DrMOS current sense gain of power stage from the register
+	 * , bits 0-2. The value is selected as below:
+	 * 00b - 5µA/A, 01b - 8.5µA/A, 10b - 9.7µA/A, 11b - 10µA/A. Other
+	 * values are reserved.
+	 */
+	ret = i2c_smbus_read_word_data(client, MP2888_MFR_SYS_CONFIG);
+	if (ret < 0)
+		return ret;
+
+	switch (ret & MP2888_DRMOS_KCS) {
+	case 0:
+		data->curr_sense_gain = 85;
+		break;
+	case 1:
+		data->curr_sense_gain = 97;
+		break;
+	case 2:
+		data->curr_sense_gain = 100;
+		break;
+	case 3:
+		data->curr_sense_gain = 50;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/*
+	 * Obtain resolution selector for total and phase current report and protection.
+	 * 0: original resolution; 1: half resolution (in such case phase current value should
+	 * be doubled.
+	 */
+	data->total_curr_resolution = (ret & MP2888_TOTAL_CURRENT_RESOLUTION) >> 3;
+	data->phase_curr_resolution = (ret & MP2888_PHASE_CURRENT_RESOLUTION) >> 4;
+
+	return 0;
+}
+
+static int
+mp2888_read_phase(struct i2c_client *client, struct mp2888_data *data, int page, int phase, u8 reg)
+{
+	int ret;
+
+	ret = pmbus_read_word_data(client, page, phase, reg);
+	if (ret < 0)
+		return ret;
+
+	if (!((phase + 1) % 2))
+		ret >>= 8;
+	ret &= 0xff;
+
+	/*
+	 * Output value is calculated as: (READ_CSx / 80 – 1.23) / (Kcs * Rcs)
+	 * where:
+	 * - Kcs is the DrMOS current sense gain of power stage, which is obtained from the
+	 *   register MP2888_MFR_VR_CONFIG1, bits 13-12 with the following selection of DrMOS
+	 *   (data->curr_sense_gain):
+	 *   00b - 5µA/A, 01b - 8.5µA/A, 10b - 9.7µA/A, 11b - 10µA/A.
+	 * - Rcs is the internal phase current sense resistor. This parameter depends on hardware
+	 *   assembly. By default it is set to 1kΩ. In case of different assembly, user should
+	 *   scale this parameter by dividing it by Rcs.
+	 * If phase current resolution bit is set to 1, READ_CSx value should be doubled.
+	 * Note, that current phase sensing, providing by the device is not accurate. This is
+	 * because sampling of current occurrence of bit weight has a big deviation, especially for
+	 * light load.
+	 */
+	ret = DIV_ROUND_CLOSEST(ret * 100 - 9800, data->curr_sense_gain);
+	if (data->phase_curr_resolution)
+		ret *= 2;
+	/* Scale according to total current resolution. */
+	if (data->total_curr_resolution)
+		ret *= 2;
+	else
+		ret *= 4;
+	return ret;
+}
+
+static int
+mp2888_read_phases(struct i2c_client *client, struct mp2888_data *data, int page, int phase)
+{
+	int ret;
+
+	switch (phase) {
+	case 0 ... 1:
+		ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS1_2);
+		break;
+	case 2 ... 3:
+		ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS3_4);
+		break;
+	case 4 ... 5:
+		ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS5_6);
+		break;
+	case 6 ... 7:
+		ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS7_8);
+		break;
+	case 8 ... 9:
+		ret = mp2888_read_phase(client, data, page, phase, MP2888_MFR_READ_CS9_10);
+		break;
+	default:
+		return -ENODATA;
+	}
+	return ret;
+}
+
+static int mp2888_read_word_data(struct i2c_client *client, int page, int phase, int reg)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct mp2888_data *data = to_mp2888_data(info);
+	int ret;
+
+	switch (reg) {
+	case PMBUS_READ_VIN:
+		ret = pmbus_read_word_data(client, page, phase, reg);
+		if (ret <= 0)
+			return ret;
+
+		/*
+		 * READ_VIN requires fixup to scale it to linear11 format. Register data format
+		 * provides 10 bits for mantissa and 6 bits for exponent. Bits 15:10 are set with
+		 * the fixed value 111011b.
+		 */
+		ret = ((ret & 0x3ff) >> 1) | (ret & ~GENMASK(11, 0));
+		break;
+	case PMBUS_OT_WARN_LIMIT:
+		ret = pmbus_read_word_data(client, page, phase, reg);
+		if (ret < 0)
+			return ret;
+		/*
+		 * Chip reports limits in degrees C, but the actual temperature in 10th of
+		 * degrees C - scaling is needed to match both.
+		 */
+		ret *= MP2888_TEMP_UNIT;
+		break;
+	case PMBUS_READ_IOUT:
+	case PMBUS_IOUT_OC_WARN_LIMIT:
+		if (phase != 0xff)
+			return mp2888_read_phases(client, data, page, phase);
+
+		ret = pmbus_read_word_data(client, page, phase, reg);
+		if (ret < 0)
+			return ret;
+		/*
+		 * READ_IOUT register has unused bits 15:12 with fixed value 1110b. Clear these
+		 * bits and scale with total current resolution. Data is provided in direct format.
+		 */
+		ret &= GENMASK(11, 0);
+		break;
+	case PMBUS_READ_POUT:
+	case PMBUS_READ_PIN:
+	case PMBUS_POUT_OP_WARN_LIMIT:
+		ret = pmbus_read_word_data(client, page, phase, reg);
+		if (ret < 0)
+			return ret;
+		ret = data->total_curr_resolution ? ret * 2 : ret;
+		break;
+	/*
+	 * The below registers are not implemented by device or implemented not according to the
+	 * spec. Skip all of them to avoid exposing non-relevant inputs to sysfs.
+	 */
+	case PMBUS_OT_FAULT_LIMIT:
+	case PMBUS_UT_WARN_LIMIT:
+	case PMBUS_UT_FAULT_LIMIT:
+	case PMBUS_VIN_UV_FAULT_LIMIT:
+	case PMBUS_VOUT_UV_WARN_LIMIT:
+	case PMBUS_VOUT_OV_WARN_LIMIT:
+	case PMBUS_VOUT_UV_FAULT_LIMIT:
+	case PMBUS_VOUT_OV_FAULT_LIMIT:
+	case PMBUS_VIN_OV_WARN_LIMIT:
+	case PMBUS_IOUT_OC_LV_FAULT_LIMIT:
+	case PMBUS_IOUT_OC_FAULT_LIMIT:
+	case PMBUS_POUT_MAX:
+	case PMBUS_IOUT_UC_FAULT_LIMIT:
+	case PMBUS_POUT_OP_FAULT_LIMIT:
+	case PMBUS_PIN_OP_WARN_LIMIT:
+	case PMBUS_MFR_VIN_MIN:
+	case PMBUS_MFR_VOUT_MIN:
+	case PMBUS_MFR_VIN_MAX:
+	case PMBUS_MFR_VOUT_MAX:
+	case PMBUS_MFR_IIN_MAX:
+	case PMBUS_MFR_IOUT_MAX:
+	case PMBUS_MFR_PIN_MAX:
+	case PMBUS_MFR_POUT_MAX:
+	case PMBUS_MFR_MAX_TEMP_1:
+		return -ENXIO;
+	default:
+		return -ENODATA;
+	}
+
+	return ret;
+}
+
+static int
+mp2888_identify_multiphase(struct i2c_client *client, struct mp2888_data *data,
+			   struct pmbus_driver_info *info)
+{
+	int i, ret;
+
+	ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 0);
+	if (ret < 0)
+		return ret;
+
+	/* Identify multiphase number - could be from 1 to 10. */
+	ret = i2c_smbus_read_word_data(client, MP2888_MFR_VR_CONFIG1);
+	if (ret <= 0)
+		return ret;
+
+	info->phases[0] = ret & GENMASK(3, 0);
+
+	/*
+	 * The device provides a total of 10 PWM pins, and can be configured to different phase
+	 * count applications for rail.
+	 */
+	if (info->phases[0] > MP2888_MAX_PHASE)
+		return -EINVAL;
+
+	/* Disable non-configured phases. */
+	for (i = info->phases[0]; i < MP2888_MAX_PHASE; i++)
+		info->pfunc[i] = 0;
+
+	return 0;
+}
+
+static struct pmbus_driver_info mp2888_info = {
+	.pages = 1,
+	.format[PSC_VOLTAGE_IN] = linear,
+	.format[PSC_VOLTAGE_OUT] = direct,
+	.format[PSC_TEMPERATURE] = direct,
+	.format[PSC_CURRENT_IN] = linear,
+	.format[PSC_CURRENT_OUT] = direct,
+	.format[PSC_POWER] = direct,
+	.m[PSC_TEMPERATURE] = 1,
+	.R[PSC_TEMPERATURE] = 1,
+	.m[PSC_VOLTAGE_OUT] = 1,
+	.R[PSC_VOLTAGE_OUT] = 3,
+	.m[PSC_CURRENT_OUT] = 4,
+	.m[PSC_POWER] = 1,
+	.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | PMBUS_HAVE_IOUT |
+		   PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
+		   PMBUS_HAVE_POUT | PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT |
+		   PMBUS_PHASE_VIRTUAL,
+	.pfunc[0] = PMBUS_HAVE_IOUT,
+	.pfunc[1] = PMBUS_HAVE_IOUT,
+	.pfunc[2] = PMBUS_HAVE_IOUT,
+	.pfunc[3] = PMBUS_HAVE_IOUT,
+	.pfunc[4] = PMBUS_HAVE_IOUT,
+	.pfunc[5] = PMBUS_HAVE_IOUT,
+	.pfunc[6] = PMBUS_HAVE_IOUT,
+	.pfunc[7] = PMBUS_HAVE_IOUT,
+	.pfunc[8] = PMBUS_HAVE_IOUT,
+	.pfunc[9] = PMBUS_HAVE_IOUT,
+	.read_byte_data = mp2888_read_byte_data,
+	.read_word_data = mp2888_read_word_data,
+};
+
+static int mp2888_probe(struct i2c_client *client)
+{
+	struct pmbus_driver_info *info;
+	struct mp2888_data *data;
+	int ret;
+
+	data = devm_kzalloc(&client->dev, sizeof(struct mp2888_data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	memcpy(&data->info, &mp2888_info, sizeof(*info));
+	info = &data->info;
+
+	/* Identify multiphase configuration. */
+	ret = mp2888_identify_multiphase(client, data, info);
+	if (ret)
+		return ret;
+
+	/* Obtain current sense gain of power stage and current resolution. */
+	ret = mp2888_current_sense_gain_and_resolution_get(client, data);
+	if (ret)
+		return ret;
+
+	if (data->total_curr_resolution) {
+		info->m[PSC_POWER] *= 2;
+		info->m[PSC_CURRENT_OUT] /= 2;
+	}
+
+	return pmbus_do_probe(client, info);
+}
+
+static const struct i2c_device_id mp2888_id[] = {
+	{"mp2888", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, mp2888_id);
+
+static const struct of_device_id __maybe_unused mp2888_of_match[] = {
+	{.compatible = "mps,mp2888"},
+	{}
+};
+MODULE_DEVICE_TABLE(of, mp2888_of_match);
+
+static struct i2c_driver mp2888_driver = {
+	.driver = {
+		.name = "mp2888",
+		.of_match_table = of_match_ptr(mp2888_of_match),
+	},
+	.probe_new = mp2888_probe,
+	.id_table = mp2888_id,
+};
+
+module_i2c_driver(mp2888_driver);
+
+MODULE_AUTHOR("Vadim Pasternak <vadimp@xxxxxxxxxx>");
+MODULE_DESCRIPTION("PMBus driver for MPS MP2888 device");
+MODULE_LICENSE("GPL");
-- 
2.11.0




[Index of Archives]     [LM Sensors]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux