On 12/23/19 9:50 PM, PGNet Dev wrote:
hi,
On 12/23/19 9:28 PM, Guenter Roeck wrote:
In the specific issue referenced above, it appears that a Nuvoton NCT6796D
was detected but not instantiated. Most likely the problem is that the IO address
range necessary to access the chip is reserved by the BIOS. Looking into the
kernel log would reveal that information. Again, that has nothing to do with
support for the CPU installed on the board, but with the board vendor and,
to a substantial degree, the lack of support for Linux by that board vendor.
not sure if this is of note,
superiotool --dump
superiotool r
No Super I/O found
superiotool only reports about chips it knows about. You might want to try
sensors-detect; it will at least tell you about unknown chips.
I've contacted Asus tech re: BIOS 'gotchas' that might be interfering; I'll pass on your comments. So far, on other issues, they've been very cooperative/helpful; we'll see how this goes.
As for the kernel log, anything specific to look for, share here? Or just grab & post the whole thing somewhere?
You'll probably see a note about an ACPI resource conflict. If the board
with NCT6796D wasn't yours, that may not be the case.
If you think something is missing that should be displayed by k10temp,
if you have documentation from AMD describing the necessary registers to
obtain this information, and if you have permission from AMD to publish
it, please feel free to submit a patch adding it to the k10temp driver.
Please make sure that the additional information follows the hardware
monitoring ABI (specifically, CPU frequencies are not part of that ABI).
Not entirely sure on the 'should' of it ... yet.
I _can_ say that, currently, for the 'new' setup, the limited info with 'k10temp' is
(1) ASUSTeK PRIME X570-PRO mobo + Ryzen7 3700X
sensors
k10temp-pci-00c3
Adapter: PCI adapter
Tdie: +59.9°C (high = +70.0°C)
Tctl: +59.9°C
and for an older board/cpu, also with 'k10temp', it's
(2) Asus M3A78-CM with a non-Ryzen, AMD Phenom II
sensors
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +42.9°C (high = +70.0°C)
(crit = +99.5°C, hyst = +97.5°C)
The register addresses for temperature limit information (if available) have
not been published by AMD for Ryzen CPUs. The same is true for other chip
specific information (voltages and power); my understanding is that AMD makes
that information only available under NDA, which is not suitable for a Linux
driver. Please feel free to contact AMD and convince them to publish the
necessary information.
atk0110-acpi-0
This is very much _not_ k10temp. As the name says, it is the atk0110 ACPI driver
for ASUS boards. Support is very much board specific, and typically depends on
someone disassembling and analyzing the DSDT of a given board.
Adapter: ACPI interface
Vcore Voltage: 1.02 V (min = +0.85 V, max = +1.60 V)
+3.3 Voltage: 3.23 V (min = +2.97 V, max = +3.63 V)
+5 Voltage: 4.86 V (min = +4.50 V, max = +5.50 V)
+12 Voltage: 12.04 V (min = +10.20 V, max = +13.80 V)
CPU FAN Speed: 2789 RPM (min = 600 RPM, max = 7200 RPM)
CHASSIS FAN Speed: 0 RPM (min = 600 RPM, max = 7200 RPM)
POWER FAN Speed: 0 RPM (min = 600 RPM, max = 7200 RPM)
CPU Temperature: +44.0°C (high = +60.0°C, crit = +95.0°C)
MB Temperature: +34.0°C (high = +45.0°C, crit = +95.0°C)
