Re: [PATCH 3/3] hwmon: lochnagar: Add Lochnagar 2 hardware monitoring driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Mar 21, 2019 at 06:14:23AM -0700, Guenter Roeck wrote:
> On 3/21/19 4:59 AM, Charles Keepax wrote:
> >On Wed, Mar 20, 2019 at 09:40:10AM -0700, Guenter Roeck wrote:
> >>On Wed, Mar 20, 2019 at 02:58:18PM +0000, Charles Keepax wrote:
> >>>From: Lucas Tanure <tanureal@xxxxxxxxxxxxxxxxxxxxx>
> >>Is this an ieee754 floating point format ? Please add a comment stating it.
> >>Also, if the format supports it, please check for NaN. If the HW guarantees
> >>to never return NaN, please add a respective comment.
> >>
> >>How likely is it that the values overflow ? A precision multipler of
> >>1,000,000,000 means that numbers will overflow quite easily. And does
> >>the the hardware really report voltages and currents in pico-units,
> >>and are temperatures really reported in micro-degrees C ?
> >>
> >
> >I believe the hardware can't return NaN. But will check that,
> >what ranges are possible and add some overflow checking.
> >
> 
> How about the units ? Maybe add a note explaining what the HW actually returns.
> 

Yup can do.

> >>Overall it might make sense to reconfigure the hardware into continuous
> >>measurement mode and get rid of the delays (if that can be configured -
> >>the user guide isn't detailed enough to be able to determine for sure).
> >>After all, it is quite unlikely that the board will be used in an
> >>environment where the power savings would be worth the inconvenience
> >>of having to wait more than two seconds for a set of measurement values
> >>(adding all the current and temperature delays up).
> >>
> >
> >Yeah the hardware is quite slow and regrettably doesn't have a
> >continuous measurement mode. We could potentially add a thread to
> >poll them but mostly the usage for this data is just taking power
> >measurements of various audio use-cases so the large delay isn't
> >a huge problem and not sure it warrents the additional
> >complexity.
> >
> >>>+	msleep(nsamples);
> >>>+
> >>
> >>This needs some explanation how nsamples translates into millisecond waits,
> >>especially since that wait can add up significantly (reading the temperature
> >>will take forever, as will reading all currents).
> >>
> >>>+	ret =  regmap_read_poll_timeout(regmap, LOCHNAGAR2_IMON_CTRL3, val,
> >>>+					val & LOCHNAGAR2_IMON_DONE_MASK,
> >>>+					5000, 2000000);
> >>
> >>Can that indeed take another two seconds on top of the sleep above ?
> >>
> >
> >It does about about 1.5-2 seconds I think last time I checked.
> >
> >Essentially the hardware will average a number of readings and
> >return that. The number of readings given in the driver is what
> >the hardware guys recommended for each, that said we could
> >potentially make it configurable if that helps at all? Also
> >I could get the msleep a bit closer to the actual runtime,
> >just need to check how linear the time is with the number of
> >samples take (I assume very).
> >
> 
> Brr. Just add a note explaining that the long times are indeed intentional,
> and that the HW takes that long.
> 

>From some more detailed discussions with the hardware guys
(shame on me for following the documentation) it seems
there isn't really much need for the temp to take so many
measurements. The current one makes sense as the hardware
actually does some analogue averaging so it should take account
of spikes in the current draw from the part under test. But
the temp should really only change slowly. I have also managed
to refine the estimates for the time taken by the measurements
so will factor that lot into the v2 as well.

Thanks very much for the review, will probably take me a few more
days to beat the last few clarifications out of the hardware guys
then I will fire up a v2.

Thanks,
Charles



[Index of Archives]     [LM Sensors]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux