Re: [RFC PATCH 6/6] riscv: dts: starfive: jh8100: add pinctrl device tree nodes

[Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>]

On 21/12/2023 09:36, Alex Soo wrote:
> Add pinctrl_east/pinctrl_west/pinctrl_gmac/pinctrl_aon device
> tree nodes for JH8100 SoC.
> 
> Signed-off-by: Alex Soo <yuklin.soo@xxxxxxxxxxxxxxxx>
> Reviewed-by: Ley Foon Tan <leyfoon.tan@xxxxxxxxxxxxxxxx>

I have some doubts about it...

> ---
>  arch/riscv/boot/dts/starfive/jh8100-evb.dts   |   5 +
>  arch/riscv/boot/dts/starfive/jh8100-pinfunc.h | 418 ++++++++++++++++++
>  arch/riscv/boot/dts/starfive/jh8100.dtsi      |  44 ++
>  3 files changed, 467 insertions(+)
>  create mode 100644 arch/riscv/boot/dts/starfive/jh8100-pinfunc.h
> 
> diff --git a/arch/riscv/boot/dts/starfive/jh8100-evb.dts b/arch/riscv/boot/dts/starfive/jh8100-evb.dts
> index c16bc25d8988..8634e41984f8 100644
> --- a/arch/riscv/boot/dts/starfive/jh8100-evb.dts
> +++ b/arch/riscv/boot/dts/starfive/jh8100-evb.dts
> @@ -26,3 +26,8 @@ memory@40000000 {
>  &uart0 {
>  	status = "okay";
>  };
> +
> +&pinctrl_aon {

Wrong order. Nodes do not go to the end.

> +	wakeup-gpios = <&pinctrl_aon PAD_RGPIO2 GPIO_ACTIVE_HIGH>;
> +	wakeup-source;

None of these were tested.

It does not look like you tested the DTS against bindings. Please run
`make dtbs_check W=1` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).

> +};
> diff --git a/arch/riscv/boot/dts/starfive/jh8100-pinfunc.h b/arch/riscv/boot/dts/starfive/jh8100-pinfunc.h
> new file mode 100644
> index 000000000000..3fb16ef62d90
> --- /dev/null
> +++ b/arch/riscv/boot/dts/starfive/jh8100-pinfunc.h
> @@ -0,0 +1,418 @@
> +/* SPDX-License-Identifier: GPL-2.0 OR MIT */
> +/*
> + * Copyright (C) 2023 StarFive Technology Co., Ltd.
> + * Author: Alex Soo <yuklin.soo@xxxxxxxxxxxxxxxx>
> + *
> + */
> +
> +#ifndef __JH8100_PINFUNC_H__
> +#define __JH8100_PINFUNC_H__
> +
> +/*
> + * mux bits:
> + *  | 31 - 24 | 23 - 16 | 15 - 10 |  9 - 8   |  7 - 0  |
> + *  |  din    |  dout   |  doen   | function | gpio nr |
> + *
> + * dout:     output signal
> + * doen:     output enable signal
> + * din:      optional input signal, 0xff = none
> + * function:
> + * gpio nr:  gpio number, 0 - 63
> + */
> +#define GPIOMUX(n, dout, doen, din) ( \
> +		(((din)  & 0xff) << 24) | \
> +		(((dout) & 0xff) << 16) | \
> +		(((doen) & 0x3f) << 10) | \
> +		((n) & 0x3f))
> +
> +#define PINMUX(n, func) ((1 << 10) | (((func) & 0x3) << 8) | ((n) & 0xff))
> +
> +/* sys_iomux_east dout */
> +#define GPOUT_LOW				0
> +#define GPOUT_HIGH				1

Where are these used?

> +#define GPOUT_SYS_CAN0_STBY			2
> +#define GPOUT_SYS_CAN0_TST_NEXT_BIT		3
> +#define GPOUT_SYS_CAN0_TST_SAMPLE_POINT		4
> +#define GPOUT_SYS_CAN0_TXD			5
> +#define GPOUT_SYS_I2C0_CLK			6
> +#define GPOUT_SYS_I2C0_DATA			7
> +#define GPOUT_SYS_I2S0_STEREO_RSCKO		8

You add here bunch of constants not used anywhere. No single example of
their usage, not a one.

Best regards,
Krzysztof