Re: [PATCH v2 2/5] dt-bindings: pinctrl: Add StarFive JH7110 sys pinctrl

[Emil Renner Berthing <emil.renner.berthing@xxxxxxxxxxxxx>]

On Mon, 28 Nov 2022 at 02:04, Jianlong Huang
<jianlong.huang@xxxxxxxxxxxxxxxx> wrote:
>
> On 2022/11/21 16:43, Krzysztof Kozlowski wrote:
> > On 18/11/2022 02:11, Hal Feng wrote:
> >> From: Jianlong Huang <jianlong.huang@xxxxxxxxxxxxxxxx>
> >>
> >> Add pinctrl bindings for StarFive JH7110 SoC sys pinctrl controller.
> >>
> >> Signed-off-by: Jianlong Huang <jianlong.huang@xxxxxxxxxxxxxxxx>
> >> Signed-off-by: Hal Feng <hal.feng@xxxxxxxxxxxxxxxx>
> >> ---
> >>  .../pinctrl/starfive,jh7110-sys-pinctrl.yaml  | 165 ++++++++++++++++++
> >>  1 file changed, 165 insertions(+)
> >>  create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
> >>
> >> diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
> >> new file mode 100644
> >> index 000000000000..79623f884a9c
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
> >> @@ -0,0 +1,165 @@
> >> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> >> +%YAML 1.2
> >> +---
> >> +$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml#
> >> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> >> +
> >> +title: StarFive JH7110 Sys Pin Controller
> >> +
> >> +description: |
> >> +  Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd.
> >> +
> >> +  Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO63
> >> +  can be multiplexed and have configurable bias, drive strength,
> >> +  schmitt trigger etc.
> >> +  Some peripherals have their I/O go through the 64 "GPIOs". This also
> >> +  includes a number of other UARTs, I2Cs, SPIs, PWMs etc.
> >> +  All these peripherals are connected to all 64 GPIOs such that
> >> +  any GPIO can be set up to be controlled by any of the peripherals.
> >> +
> >> +maintainers:
> >> +  - Jianlong Huang <jianlong.huang@xxxxxxxxxxxxxxxx>
> >> +
> >> +properties:
> >> +  compatible:
> >> +    const: starfive,jh7110-sys-pinctrl
> >> +
> >> +  reg:
> >> +    maxItems: 1
> >> +
> >> +  reg-names:
> >> +    items:
> >> +      - const: control
> >
> > Why reg-names for one entry? Perhaps just drop it.
>
> Will fix, drop it.
>
> >
> >> +
> >> +  clocks:
> >> +    maxItems: 1
> >> +
> >> +  resets:
> >> +    maxItems: 1
> >> +
> >> +  gpio-controller: true
> >> +
> >> +  "#gpio-cells":
> >> +    const: 2
> >> +
> >> +  interrupts:
> >> +    maxItems: 1
> >> +    description: The GPIO parent interrupt.
> >
> > Drop description, it's obvious.
>
> Will fix, drop it.
>
> >
> >> +
> >> +  interrupt-controller: true
> >> +
> >> +  "#interrupt-cells":
> >> +    const: 2
> >> +
> >> +required:
> >> +  - compatible
> >> +  - reg
> >> +  - reg-names
> >> +  - clocks
> >> +  - gpio-controller
> >> +  - "#gpio-cells"
> >> +  - interrupts
> >> +  - interrupt-controller
> >> +  - "#interrupt-cells"
> >> +
> >> +patternProperties:
> >> +  '-[0-9]+$':
> >
> > Keep consistent quotes, either ' or "
> >
> > How do you differentiate hogs? The pattern is a bit unspecific.
>
> Will fix.
> Keep consisitent quotes, use '
>
> >
> >> +    type: object
> >> +    patternProperties:
> >> +      '-pins$':
> >> +        type: object
> >> +        description: |
> >> +          A pinctrl node should contain at least one subnode representing the
> >> +          pinctrl groups available on the machine. Each subnode will list the
> >> +          pins it needs, and how they should be configured, with regard to
> >> +          muxer configuration, system signal configuration, pin groups for
> >> +          vin/vout module, pin voltage, mux functions for output, mux functions
> >> +          for output enable, mux functions for input.
> >> +
> >> +        properties:
> >> +          pinmux:
> >> +            description: |
> >> +              The list of GPIOs and their mux settings that properties in the
> >> +              node apply to. This should be set using the GPIOMUX macro.
> >> +            $ref: "/schemas/pinctrl/pinmux-node.yaml#/properties/pinmux"
> >
> > Drop quotes.
>
> Will fix, drop quotes.
>
> >
> >> +
> >> +          bias-disable: true
> >> +
> >> +          bias-pull-up:
> >> +            type: boolean
> >> +
> >> +          bias-pull-down:
> >> +            type: boolean
> >> +
> >> +          drive-strength:
> >> +            enum: [ 2, 4, 8, 12 ]
> >> +
> >> +          input-enable: true
> >> +
> >> +          input-disable: true
> >> +
> >> +          input-schmitt-enable: true
> >> +
> >> +          input-schmitt-disable: true
> >> +
> >> +          slew-rate:
> >> +            maximum: 1
> >> +
> >> +        additionalProperties: false
> >> +
> >> +    additionalProperties: false
> >> +
> >> +additionalProperties: false
> >> +
> >> +examples:
> >> +  - |
> >> +    #include <dt-bindings/clock/starfive-jh7110.h>
> >> +    #include <dt-bindings/reset/starfive-jh7110.h>
> >> +    #include <dt-bindings/pinctrl/pinctrl-starfive-jh7110.h>
> >> +
> >> +        soc {
> >
> > Use 4 spaces for example indentation.
>
> Will fix.
>
> >
> >> +                #address-cells = <2>;
> >> +                #size-cells = <2>;

You can also drop these to lines..

> >> +
> >> +                gpio: gpio@13040000 {
> >> +                        compatible = "starfive,jh7110-sys-pinctrl";
> >> +                        reg = <0x0 0x13040000 0x0 0x10000>;

..and then just make this
reg = <0x13040000 0x10000>;

> >> +                        reg-names = "control";
> >> +                        clocks = <&syscrg_clk JH7110_SYSCLK_IOMUX>;
> >> +                        resets = <&syscrg_rst JH7110_SYSRST_IOMUX>;
> >> +                        interrupts = <86>;
> >> +                        interrupt-controller;
> >> +                        #interrupt-cells = <2>;
> >> +                        #gpio-cells = <2>;
> >> +                        gpio-controller;
> >> +                        status = "okay";
> >
> > No status in examples.
>
> Will fix, drop it.
>
> >
> >> +
> >> +                        uart0_pins: uart0-0 {
> >> +                                tx-pins {
> >> +                                        pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX, GPOEN_ENABLE, GPI_NONE)>;
> >> +                                        bias-disable;
> >> +                                        drive-strength = <12>;
> >> +                                        input-disable;
> >> +                                        input-schmitt-disable;
> >> +                                        slew-rate = <0>;
> >> +                                };
> >> +
> >> +                                rx-pins {
> >> +                                        pinmux = <GPIOMUX(6, GPOUT_LOW, GPOEN_DISABLE, GPI_SYS_UART0_RX)>;
> >> +                                        bias-pull-up;
> >> +                                        drive-strength = <2>;
> >> +                                        input-enable;
> >> +                                        input-schmitt-enable;
> >> +                                        slew-rate = <0>;
> >> +                                };
> >> +                        };
> >> +                };
> >> +
> >> +                uart0 {
> >> +                        pinctrl-names = "default";
> >> +                        pinctrl-0 = <&uart0_pins>;
> >> +                        status = "okay";
> >
> > Drop this node, useless.
>
> Will fix, drop this node.
>
> >
> >> +                };
> >> +        };
> >> +
> >> +...
> >
>
> Best regards,
> Jianlong Huang
>
>