Re: [PATCH v2 2/5] dt-bindings: pinctrl: Add StarFive JH7110 sys pinctrl

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2022/11/21 16:43, Krzysztof Kozlowski wrote:
> On 18/11/2022 02:11, Hal Feng wrote:
>> From: Jianlong Huang <jianlong.huang@xxxxxxxxxxxxxxxx>
>> 
>> Add pinctrl bindings for StarFive JH7110 SoC sys pinctrl controller.
>> 
>> Signed-off-by: Jianlong Huang <jianlong.huang@xxxxxxxxxxxxxxxx>
>> Signed-off-by: Hal Feng <hal.feng@xxxxxxxxxxxxxxxx>
>> ---
>>  .../pinctrl/starfive,jh7110-sys-pinctrl.yaml  | 165 ++++++++++++++++++
>>  1 file changed, 165 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
>> 
>> diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
>> new file mode 100644
>> index 000000000000..79623f884a9c
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
>> @@ -0,0 +1,165 @@
>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: StarFive JH7110 Sys Pin Controller
>> +
>> +description: |
>> +  Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd.
>> +
>> +  Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO63
>> +  can be multiplexed and have configurable bias, drive strength,
>> +  schmitt trigger etc.
>> +  Some peripherals have their I/O go through the 64 "GPIOs". This also
>> +  includes a number of other UARTs, I2Cs, SPIs, PWMs etc.
>> +  All these peripherals are connected to all 64 GPIOs such that
>> +  any GPIO can be set up to be controlled by any of the peripherals.
>> +
>> +maintainers:
>> +  - Jianlong Huang <jianlong.huang@xxxxxxxxxxxxxxxx>
>> +
>> +properties:
>> +  compatible:
>> +    const: starfive,jh7110-sys-pinctrl
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  reg-names:
>> +    items:
>> +      - const: control
> 
> Why reg-names for one entry? Perhaps just drop it.

Will fix, drop it.

> 
>> +
>> +  clocks:
>> +    maxItems: 1
>> +
>> +  resets:
>> +    maxItems: 1
>> +
>> +  gpio-controller: true
>> +
>> +  "#gpio-cells":
>> +    const: 2
>> +
>> +  interrupts:
>> +    maxItems: 1
>> +    description: The GPIO parent interrupt.
> 
> Drop description, it's obvious.

Will fix, drop it.

> 
>> +
>> +  interrupt-controller: true
>> +
>> +  "#interrupt-cells":
>> +    const: 2
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - reg-names
>> +  - clocks
>> +  - gpio-controller
>> +  - "#gpio-cells"
>> +  - interrupts
>> +  - interrupt-controller
>> +  - "#interrupt-cells"
>> +
>> +patternProperties:
>> +  '-[0-9]+$':
> 
> Keep consistent quotes, either ' or "
> 
> How do you differentiate hogs? The pattern is a bit unspecific.

Will fix.
Keep consisitent quotes, use '

> 
>> +    type: object
>> +    patternProperties:
>> +      '-pins$':
>> +        type: object
>> +        description: |
>> +          A pinctrl node should contain at least one subnode representing the
>> +          pinctrl groups available on the machine. Each subnode will list the
>> +          pins it needs, and how they should be configured, with regard to
>> +          muxer configuration, system signal configuration, pin groups for
>> +          vin/vout module, pin voltage, mux functions for output, mux functions
>> +          for output enable, mux functions for input.
>> +
>> +        properties:
>> +          pinmux:
>> +            description: |
>> +              The list of GPIOs and their mux settings that properties in the
>> +              node apply to. This should be set using the GPIOMUX macro.
>> +            $ref: "/schemas/pinctrl/pinmux-node.yaml#/properties/pinmux"
> 
> Drop quotes.

Will fix, drop quotes.

> 
>> +
>> +          bias-disable: true
>> +
>> +          bias-pull-up:
>> +            type: boolean
>> +
>> +          bias-pull-down:
>> +            type: boolean
>> +
>> +          drive-strength:
>> +            enum: [ 2, 4, 8, 12 ]
>> +
>> +          input-enable: true
>> +
>> +          input-disable: true
>> +
>> +          input-schmitt-enable: true
>> +
>> +          input-schmitt-disable: true
>> +
>> +          slew-rate:
>> +            maximum: 1
>> +
>> +        additionalProperties: false
>> +
>> +    additionalProperties: false
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> +  - |
>> +    #include <dt-bindings/clock/starfive-jh7110.h>
>> +    #include <dt-bindings/reset/starfive-jh7110.h>
>> +    #include <dt-bindings/pinctrl/pinctrl-starfive-jh7110.h>
>> +
>> +        soc {
> 
> Use 4 spaces for example indentation.

Will fix.

> 
>> +                #address-cells = <2>;
>> +                #size-cells = <2>;
>> +
>> +                gpio: gpio@13040000 {
>> +                        compatible = "starfive,jh7110-sys-pinctrl";
>> +                        reg = <0x0 0x13040000 0x0 0x10000>;
>> +                        reg-names = "control";
>> +                        clocks = <&syscrg_clk JH7110_SYSCLK_IOMUX>;
>> +                        resets = <&syscrg_rst JH7110_SYSRST_IOMUX>;
>> +                        interrupts = <86>;
>> +                        interrupt-controller;
>> +                        #interrupt-cells = <2>;
>> +                        #gpio-cells = <2>;
>> +                        gpio-controller;
>> +                        status = "okay";
> 
> No status in examples.

Will fix, drop it.

> 
>> +
>> +                        uart0_pins: uart0-0 {
>> +                                tx-pins {
>> +                                        pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX, GPOEN_ENABLE, GPI_NONE)>;
>> +                                        bias-disable;
>> +                                        drive-strength = <12>;
>> +                                        input-disable;
>> +                                        input-schmitt-disable;
>> +                                        slew-rate = <0>;
>> +                                };
>> +
>> +                                rx-pins {
>> +                                        pinmux = <GPIOMUX(6, GPOUT_LOW, GPOEN_DISABLE, GPI_SYS_UART0_RX)>;
>> +                                        bias-pull-up;
>> +                                        drive-strength = <2>;
>> +                                        input-enable;
>> +                                        input-schmitt-enable;
>> +                                        slew-rate = <0>;
>> +                                };
>> +                        };
>> +                };
>> +
>> +                uart0 {
>> +                        pinctrl-names = "default";
>> +                        pinctrl-0 = <&uart0_pins>;
>> +                        status = "okay";
> 
> Drop this node, useless.

Will fix, drop this node.

> 
>> +                };
>> +        };
>> +
>> +...
> 

Best regards,
Jianlong Huang





[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux