On 11/2/21 19:54, Jesse Taube wrote:
On 11/2/21 19:42, Fabio Estevam wrote:
On Tue, Nov 2, 2021 at 7:57 PM Jesse Taube <mr.bossman075@xxxxxxxxx> wrote:
+/ {
+ model = "NXP IMXRT1050-evk board";
+ compatible = "fsl,imxrt1050-evk", "fsl,imxrt1050";
+
+ chosen {
+ bootargs = "root=/dev/ram";
No need to pass bootargs here.
+ stdout-path = &lpuart1;
+ };
+
+ aliases {
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ gpio4 = &gpio5;
+ mmc0 = &usdhc1;
+ serial0 = &lpuart1;
+ };
+
+ memory@0 {
memory@80000000
Building with W=1 should give a dtc warning due to the unit address
and reg mismatch.
Oh that makes sense.
I guess I'm going to have to figure out how to get warnings to work as I
couldn't last time I tried.
Oh i got it to work I did something dumb...
I didn't give a warning for this i still changed it of course.
+ device_type = "memory";
+ reg = <0x80000000 0x2000000>;
+ };
+
Unneeded blank line.
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ imxrt1050-evk {
No need for this imxrt1050-evk container.
I was wondering if that was needed, u-boot has it, good to know.
+ pinctrl_lpuart1: lpuart1grp {
+ fsl,pins = <
+ MXRT1050_IOMUXC_GPIO_AD_B0_12_LPUART1_TXD
+ 0xf1
Put it on a single line. It helps readability. Same applies globally.
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+ pinctrl-0 = <&pinctrl_usdhc0>;
+ pinctrl-1 = <&pinctrl_usdhc0>;
+ pinctrl-2 = <&pinctrl_usdhc0>;
+ pinctrl-3 = <&pinctrl_usdhc0>;
+ status = "okay";
+
+ cd-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
Make 'status' to be the last property. Remove the blank line.
+ edma1: dma-controller@400e8000 {
+ #dma-cells = <2>;
+ compatible = "fsl,imx7ulp-edma";
+ reg = <0x400e8000 0x4000>,
+ <0x400ec000 0x4000>;
+ dma-channels = <32>;
+ interrupts = <0>,
+ <1>,
+ <2>,
+ <3>,
+ <4>,
+ <5>,
+ <6>,
+ <7>,
+ <8>,
+ <9>,
+ <10>,
+ <11>,
+ <12>,
+ <13>,
+ <14>,
+ <15>,
+ <16>;
Please group more elements into the same line.
Putting one entry per line makes it extremely long.
+ gpio5: gpio@400c0000 {
+ compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio";
+ reg = <0x400c0000 0x4000>;
+ interrupts = <88>,
+ <89>;
Put the interrupts into a single line.
Ah all these make sense, will fix, sry about that.
