Re: [PATCH v2 12/13] ARM: dts: imx: add i.MXRT1050-EVK support

[Fabio Estevam <festevam@xxxxxxxxx>]

On Tue, Nov 2, 2021 at 7:57 PM Jesse Taube <mr.bossman075@xxxxxxxxx> wrote:

> +/ {
> +       model = "NXP IMXRT1050-evk board";
> +       compatible = "fsl,imxrt1050-evk", "fsl,imxrt1050";
> +
> +       chosen {
> +               bootargs = "root=/dev/ram";

No need to pass bootargs here.

> +               stdout-path = &lpuart1;
> +       };
> +
> +       aliases {
> +               gpio0 = &gpio1;
> +               gpio1 = &gpio2;
> +               gpio2 = &gpio3;
> +               gpio3 = &gpio4;
> +               gpio4 = &gpio5;
> +               mmc0 = &usdhc1;
> +               serial0 = &lpuart1;
> +       };
> +
> +       memory@0 {

memory@80000000

Building with W=1 should give a dtc warning due to the unit address
and reg mismatch.

> +               device_type = "memory";
> +               reg = <0x80000000 0x2000000>;
> +       };
> +

Unneeded blank line.
> +
> +&iomuxc {
> +       pinctrl-names = "default";
> +
> +       imxrt1050-evk {

No need for this imxrt1050-evk container.

> +               pinctrl_lpuart1: lpuart1grp {
> +                       fsl,pins = <
> +                               MXRT1050_IOMUXC_GPIO_AD_B0_12_LPUART1_TXD
> +                                       0xf1

Put it on a single line. It helps readability. Same applies globally.
> +&usdhc1 {
> +       pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
> +       pinctrl-0 = <&pinctrl_usdhc0>;
> +       pinctrl-1 = <&pinctrl_usdhc0>;
> +       pinctrl-2 = <&pinctrl_usdhc0>;
> +       pinctrl-3 = <&pinctrl_usdhc0>;
> +       status = "okay";
> +
> +       cd-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;

Make 'status' to be the last property. Remove the blank line.

> +               edma1: dma-controller@400e8000 {
> +                       #dma-cells = <2>;
> +                       compatible = "fsl,imx7ulp-edma";
> +                       reg = <0x400e8000 0x4000>,
> +                               <0x400ec000 0x4000>;
> +                       dma-channels = <32>;
> +                       interrupts = <0>,
> +                               <1>,
> +                               <2>,
> +                               <3>,
> +                               <4>,
> +                               <5>,
> +                               <6>,
> +                               <7>,
> +                               <8>,
> +                               <9>,
> +                               <10>,
> +                               <11>,
> +                               <12>,
> +                               <13>,
> +                               <14>,
> +                               <15>,
> +                               <16>;

Please group more elements into the same line.

Putting one entry per line makes it extremely long.

> +               gpio5: gpio@400c0000 {
> +                       compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio";
> +                       reg = <0x400c0000 0x4000>;
> +                       interrupts = <88>,
> +                               <89>;

Put the interrupts into a single line.