Re: [PATCH 5/9] arm64: dts: rockchip: add rk3568 tsadc nodes

[Heiko Stübner <heiko@xxxxxxxxx>]

Am Mittwoch, 28. Juli 2021, 17:14:17 CEST schrieb Peter Geis:
> On Wed, Jul 28, 2021 at 10:46 AM Heiko Stübner <heiko@xxxxxxxxx> wrote:
> >
> > Am Mittwoch, 28. Juli 2021, 15:55:30 CEST schrieb Peter Geis:
> > > Add the thermal and tsadc nodes to the rk3568 device tree.
> > > There are two sensors, one for the cpu, one for the gpu.
> > >
> > > Signed-off-by: Peter Geis <pgwipeout@xxxxxxxxx>
> > > ---
> > >  .../boot/dts/rockchip/rk3568-pinctrl.dtsi     |  6 ++
> > >  arch/arm64/boot/dts/rockchip/rk356x.dtsi      | 71 +++++++++++++++++++
> > >  2 files changed, 77 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi b/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
> > > index a588ca95ace2..b464c7bda1f7 100644
> > > --- a/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
> > > +++ b/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
> > > @@ -2420,6 +2420,12 @@ spi3m1_cs1: spi3m1-cs1 {
> > >       };
> > >
> > >       tsadc {
> > > +             /omit-if-no-ref/
> > > +             tsadc_gpio: tsadc-gpio {
> > > +                     rockchip,pins =
> > > +                             <0 RK_PA1 0 &pcfg_pull_none>;
> > > +             };
> > > +
> > >               /omit-if-no-ref/
> > >               tsadcm0_shut: tsadcm0-shut {
> > >                       rockchip,pins =
> > > diff --git a/arch/arm64/boot/dts/rockchip/rk356x.dtsi b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > > index 77c679304916..0905fac0726a 100644
> > > --- a/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > > +++ b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > > @@ -51,6 +51,7 @@ cpu0: cpu@0 {
> > >                       compatible = "arm,cortex-a55";
> > >                       reg = <0x0 0x0>;
> > >                       clocks = <&scmi_clk 0>;
> > > +                     #cooling-cells = <2>;
> > >                       enable-method = "psci";
> > >                       operating-points-v2 = <&cpu0_opp_table>;
> > >               };
> > > @@ -59,6 +60,7 @@ cpu1: cpu@100 {
> > >                       device_type = "cpu";
> > >                       compatible = "arm,cortex-a55";
> > >                       reg = <0x0 0x100>;
> > > +                     #cooling-cells = <2>;
> > >                       enable-method = "psci";
> > >                       operating-points-v2 = <&cpu0_opp_table>;
> > >               };
> > > @@ -67,6 +69,7 @@ cpu2: cpu@200 {
> > >                       device_type = "cpu";
> > >                       compatible = "arm,cortex-a55";
> > >                       reg = <0x0 0x200>;
> > > +                     #cooling-cells = <2>;
> > >                       enable-method = "psci";
> > >                       operating-points-v2 = <&cpu0_opp_table>;
> > >               };
> > > @@ -75,6 +78,7 @@ cpu3: cpu@300 {
> > >                       device_type = "cpu";
> > >                       compatible = "arm,cortex-a55";
> > >                       reg = <0x0 0x300>;
> > > +                     #cooling-cells = <2>;
> > >                       enable-method = "psci";
> > >                       operating-points-v2 = <&cpu0_opp_table>;
> > >               };
> > > @@ -774,6 +778,73 @@ uart9: serial@fe6d0000 {
> > >               status = "disabled";
> > >       };
> > >
> > > +     thermal_zones: thermal-zones {
> > > +             cpu_thermal: cpu-thermal {
> > > +                     polling-delay-passive = <100>;
> > > +                     polling-delay = <1000>;
> > > +
> > > +                     thermal-sensors = <&tsadc 0>;
> > > +
> > > +                     trips {
> > > +                             cpu_alert0: cpu_alert0 {
> > > +                                     temperature = <70000>;
> > > +                                     hysteresis = <2000>;
> > > +                                     type = "passive";
> > > +                             };
> > > +                             cpu_alert1: cpu_alert1 {
> > > +                                     temperature = <75000>;
> > > +                                     hysteresis = <2000>;
> > > +                                     type = "passive";
> > > +                             };
> > > +                             cpu_crit: cpu_crit {
> > > +                                     temperature = <95000>;
> > > +                                     hysteresis = <2000>;
> > > +                                     type = "critical";
> > > +                             };
> > > +                     };
> > > +
> > > +                     cooling-maps {
> > > +                             map0 {
> > > +                                     trip = <&cpu_alert0>;
> > > +                                     cooling-device =
> > > +                                             <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> > > +                                             <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> > > +                                             <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> > > +                                             <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> > > +                             };
> > > +                     };
> > > +             };
> > > +
> > > +             gpu_thermal: gpu-thermal {
> > > +                     polling-delay-passive = <20>; /* milliseconds */
> > > +                     polling-delay = <1000>; /* milliseconds */
> > > +
> > > +                     thermal-sensors = <&tsadc 1>;
> > > +             };
> > > +     };
> > > +
> > > +     tsadc: tsadc@fe710000 {
> > > +             compatible = "rockchip,rk3568-tsadc";
> > > +             reg = <0x0 0xfe710000 0x0 0x100>;
> > > +             interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
> > > +             assigned-clocks = <&cru CLK_TSADC_TSEN>, <&cru CLK_TSADC>;
> > > +             assigned-clock-rates = <17000000>, <700000>;
> > > +             clocks = <&cru CLK_TSADC>, <&cru PCLK_TSADC>;
> > > +             clock-names = "tsadc", "apb_pclk";
> > > +             resets = <&cru SRST_TSADC>, <&cru SRST_P_TSADC>,
> > > +                      <&cru SRST_TSADCPHY>;
> > > +             reset-names = "tsadc", "tsadc-apb", "tsadc-phy";
> > > +             rockchip,grf = <&grf>;
> > > +             rockchip,hw-tshut-temp = <95000>;
> > > +             rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
> > > +             rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
> > > +             pinctrl-names = "gpio", "otpout";
> > > +             pinctrl-0 = <&tsadc_gpio>;
> > > +             pinctrl-1 = <&tsadc_shutorg>;
> >
> > The mainline thermal driver doesn't specify these pinctrl states at all.
> >
> > Heiko
> 
> Oh, yes this seems to be the case.
> 
> Is this something that should get fixed?
> In practice it likely won't ever cause problems, but in theory if
> someone changed the pinmux mode it could break it.

take a look at for example the rk3399.dtsi where the tsadc uses
the generic pinctrl names of "init" (before-probe), "default" (after probe)
and "sleep"


Heiko

> 
> >
> > > +             #thermal-sensor-cells = <1>;
> > > +             status = "disabled";
> > > +     };
> > > +
> > >       saradc: saradc@fe720000 {
> > >               compatible = "rockchip,rk3568-saradc", "rockchip,rk3399-saradc";
> > >               reg = <0x0 0xfe720000 0x0 0x100>;
> > >
> >
> >
> >
> >
>