On Fri, Aug 21, 2020 at 01:19:56PM +0200, Geert Uytterhoeven wrote:
> Convert the Renesas RZ/A1 combined Pin and GPIO controller Device Tree
> binding documentation to json-schema.
>
> Rename "rza1-pinctrl" to "rza1-ports", to match the compatible value
> scheme.
> Use "pinctrl" generic node name.
> Drop generic and consumer examples, as they do not belong here.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
> ---
> Note: "phandle: true" is needed because dt-schema does not add it
> automatically to subnodes.
>
> This depends on "[PATCH] pinctrl: rza1: Switch to using "output-enable".
> To be queued in sh-pfc for v5.10.
> ---
> .../bindings/pinctrl/renesas,rza1-pinctrl.txt | 222 ------------------
> .../bindings/pinctrl/renesas,rza1-ports.yaml | 190 +++++++++++++++
> 2 files changed, 190 insertions(+), 222 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt
> create mode 100644 Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt
> deleted file mode 100644
> index 38cdd23d3498e74a..0000000000000000
> --- a/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt
> +++ /dev/null
> @@ -1,222 +0,0 @@
> -Renesas RZ/A1 combined Pin and GPIO controller
> -
> -The Renesas SoCs of the RZ/A1 family feature a combined Pin and GPIO controller,
> -named "Ports" in the hardware reference manual.
> -Pin multiplexing and GPIO configuration is performed on a per-pin basis
> -writing configuration values to per-port register sets.
> -Each "port" features up to 16 pins, each of them configurable for GPIO
> -function (port mode) or in alternate function mode.
> -Up to 8 different alternate function modes exist for each single pin.
> -
> -Pin controller node
> --------------------
> -
> -Required properties:
> - - compatible: should be:
> - - "renesas,r7s72100-ports": for RZ/A1H
> - - "renesas,r7s72101-ports", "renesas,r7s72100-ports": for RZ/A1M
> - - "renesas,r7s72102-ports": for RZ/A1L
> -
> - - reg
> - address base and length of the memory area where the pin controller
> - hardware is mapped to.
> -
> -Example:
> -Pin controller node for RZ/A1H SoC (r7s72100)
> -
> -pinctrl: pin-controller@fcfe3000 {
> - compatible = "renesas,r7s72100-ports";
> -
> - reg = <0xfcfe3000 0x4230>;
> -};
> -
> -Sub-nodes
> ----------
> -
> -The child nodes of the pin controller node describe a pin multiplexing
> -function or a GPIO controller alternatively.
> -
> -- Pin multiplexing sub-nodes:
> - A pin multiplexing sub-node describes how to configure a set of
> - (or a single) pin in some desired alternate function mode.
> - A single sub-node may define several pin configurations.
> - A few alternate function require special pin configuration flags to be
> - supplied along with the alternate function configuration number.
> - The hardware reference manual specifies when a pin function requires
> - "software IO driven" mode to be specified. To do so use the generic
> - properties from the <include/linux/pinctrl/pinconf_generic.h> header file
> - to instruct the pin controller to perform the desired pin configuration
> - operation.
> - Please refer to pinctrl-bindings.txt to get to know more on generic
> - pin properties usage.
> -
> - The allowed generic formats for a pin multiplexing sub-node are the
> - following ones:
> -
> - node-1 {
> - pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
> - GENERIC_PINCONFIG;
> - };
> -
> - node-2 {
> - sub-node-1 {
> - pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
> - GENERIC_PINCONFIG;
> - };
> -
> - sub-node-2 {
> - pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
> - GENERIC_PINCONFIG;
> - };
> -
> - ...
> -
> - sub-node-n {
> - pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ;
> - GENERIC_PINCONFIG;
> - };
> - };
> -
> - Use the second format when pins part of the same logical group need to have
> - different generic pin configuration flags applied.
> -
> - Client sub-nodes shall refer to pin multiplexing sub-nodes using the phandle
> - of the most external one.
> -
> - Eg.
> -
> - client-1 {
> - ...
> - pinctrl-0 = <&node-1>;
> - ...
> - };
> -
> - client-2 {
> - ...
> - pinctrl-0 = <&node-2>;
> - ...
> - };
> -
> - Required properties:
> - - pinmux:
> - integer array representing pin number and pin multiplexing configuration.
> - When a pin has to be configured in alternate function mode, use this
> - property to identify the pin by its global index, and provide its
> - alternate function configuration number along with it.
> - When multiple pins are required to be configured as part of the same
> - alternate function they shall be specified as members of the same
> - argument list of a single "pinmux" property.
> - Helper macros to ease assembling the pin index from its position
> - (port where it sits on and pin number) and alternate function identifier
> - are provided by the pin controller header file at:
> - <include/dt-bindings/pinctrl/r7s72100-pinctrl.h>
> - Integers values in "pinmux" argument list are assembled as:
> - ((PORT * 16 + PIN) | MUX_FUNC << 16)
> -
> - Optional generic properties:
> - - input-enable:
> - enable input bufer for pins requiring software driven IO input
> - operations.
> - - output-enable:
> - enable output buffer for pins requiring software driven IO output
> - operations.
> -
> - The hardware reference manual specifies when a pin has to be configured to
> - work in bi-directional mode and when the IO direction has to be specified
> - by software. Bi-directional pins are managed by the pin controller driver
> - internally, while software driven IO direction has to be explicitly
> - selected when multiple options are available.
> -
> - Example:
> - A serial communication interface with a TX output pin and an RX input pin.
> -
> - &pinctrl {
> - scif2_pins: serial2 {
> - pinmux = <RZA1_PINMUX(3, 0, 6)>, <RZA1_PINMUX(3, 2, 4)>;
> - };
> - };
> -
> - Pin #0 on port #3 is configured as alternate function #6.
> - Pin #2 on port #3 is configured as alternate function #4.
> -
> - Example 2:
> - I2c master: both SDA and SCL pins need bi-directional operations
> -
> - &pinctrl {
> - i2c2_pins: i2c2 {
> - pinmux = <RZA1_PINMUX(1, 4, 1)>, <RZA1_PINMUX(1, 5, 1)>;
> - };
> - };
> -
> - Pin #4 on port #1 is configured as alternate function #1.
> - Pin #5 on port #1 is configured as alternate function #1.
> - Both need to work in bi-directional mode, the driver manages this internally.
> -
> - Example 3:
> - Multi-function timer input and output compare pins.
> - Configure TIOC0A as software driven input and TIOC0B as software driven
> - output.
> -
> - &pinctrl {
> - tioc0_pins: tioc0 {
> - tioc0_input_pins {
> - pinumx = <RZA1_PINMUX(4, 0, 2)>;
> - input-enable;
> - };
> -
> - tioc0_output_pins {
> - pinmux = <RZA1_PINMUX(4, 1, 1)>;
> - output-enable;
> - };
> - };
> - };
> -
> - &tioc0 {
> - ...
> - pinctrl-0 = <&tioc0_pins>;
> - ...
> - };
> -
> - Pin #0 on port #4 is configured as alternate function #2 with IO direction
> - specified by software as input.
> - Pin #1 on port #4 is configured as alternate function #1 with IO direction
> - specified by software as output.
> -
> -- GPIO controller sub-nodes:
> - Each port of the r7s72100 pin controller hardware is itself a GPIO controller.
> - Different SoCs have different numbers of available pins per port, but
> - generally speaking, each of them can be configured in GPIO ("port") mode
> - on this hardware.
> - Describe GPIO controllers using sub-nodes with the following properties.
> -
> - Required properties:
> - - gpio-controller
> - empty property as defined by the GPIO bindings documentation.
> - - #gpio-cells
> - number of cells required to identify and configure a GPIO.
> - Shall be 2.
> - - gpio-ranges
> - Describes a GPIO controller specifying its specific pin base, the pin
> - base in the global pin numbering space, and the number of controlled
> - pins, as defined by the GPIO bindings documentation. Refer to
> - Documentation/devicetree/bindings/gpio/gpio.txt file for a more detailed
> - description.
> -
> - Example:
> - A GPIO controller node, controlling 16 pins indexed from 0.
> - The GPIO controller base in the global pin indexing space is pin 48, thus
> - pins [0 - 15] on this controller map to pins [48 - 63] in the global pin
> - indexing space.
> -
> - port3: gpio-3 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - gpio-ranges = <&pinctrl 0 48 16>;
> - };
> -
> - A device node willing to use pins controlled by this GPIO controller, shall
> - refer to it as follows:
> -
> - led1 {
> - gpios = <&port3 10 GPIO_ACTIVE_LOW>;
> - };
> diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml
> new file mode 100644
> index 0000000000000000..7f80578dc229fb84
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml
> @@ -0,0 +1,190 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/renesas,rza1-ports.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Renesas RZ/A1 combined Pin and GPIO controller
> +
> +maintainers:
> + - Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> + - Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
> +
> +description:
> + The Renesas SoCs of the RZ/A1 family feature a combined Pin and GPIO
> + controller, named "Ports" in the hardware reference manual.
> + Pin multiplexing and GPIO configuration is performed on a per-pin basis
> + writing configuration values to per-port register sets.
> + Each "port" features up to 16 pins, each of them configurable for GPIO
> + function (port mode) or in alternate function mode.
> + Up to 8 different alternate function modes exist for each single pin.
> +
> +properties:
> + compatible:
> + oneOf:
> + - const: renesas,r7s72100-ports # RZ/A1H
> + - items:
> + - const: renesas,r7s72101-ports # RZ/A1M
> + - const: renesas,r7s72100-ports # fallback
> + - const: renesas,r7s72102-ports # RZ/A1L
> +
> + reg:
> + maxItems: 1
> +
> +required:
> + - compatible
> + - reg
> +
> +patternProperties:
> + "^gpio-[0-9]*$":
> + type: object
> +
> + description:
> + Each port of the r7s72100 pin controller hardware is itself a GPIO
> + controller.
> + Different SoCs have different numbers of available pins per port, but
> + generally speaking, each of them can be configured in GPIO ("port") mode
> + on this hardware.
> + Describe GPIO controllers using sub-nodes with the following properties.
> +
> + properties:
> + gpio-controller: true
> +
> + '#gpio-cells':
> + const: 2
> +
> + gpio-ranges:
> + maxItems: 1
> +
> + required:
> + - gpio-controller
Doesn't 'true' imply required ?
> + - '#gpio-cells'
> + - gpio-ranges
> +
> +
> +additionalProperties:
> + anyOf:
Confused by this part. This describes a GPIO consumer, doesn't it ?
Does this part belong here ?
Thanks
j
> + - type: object
> + allOf:
> + - $ref: pincfg-node.yaml#
> + - $ref: pinmux-node.yaml#
> +
> + description:
> + A pin multiplexing sub-node describes how to configure a set of (or a
> + single) pin in some desired alternate function mode.
> + A single sub-node may define several pin configurations.
> + A few alternate function require special pin configuration flags to be
> + supplied along with the alternate function configuration number.
> + The hardware reference manual specifies when a pin function requires
> + "software IO driven" mode to be specified. To do so use the generic
> + properties from the <include/linux/pinctrl/pinconf_generic.h> header
> + file to instruct the pin controller to perform the desired pin
> + configuration operation.
> + The hardware reference manual specifies when a pin has to be configured
> + to work in bi-directional mode and when the IO direction has to be
> + specified by software. Bi-directional pins must be managed by the pin
> + controller driver internally, while software driven IO direction has to
> + be explicitly selected when multiple options are available.
> +
> + properties:
> + pinmux:
> + description: |
> + Integer array representing pin number and pin multiplexing
> + configuration.
> + When a pin has to be configured in alternate function mode, use
> + this property to identify the pin by its global index, and provide
> + its alternate function configuration number along with it.
> + When multiple pins are required to be configured as part of the
> + same alternate function they shall be specified as members of the
> + same argument list of a single "pinmux" property.
> + Helper macros to ease assembling the pin index from its position
> + (port where it sits on and pin number) and alternate function
> + identifier are provided by the pin controller header file at:
> + <include/dt-bindings/pinctrl/r7s72100-pinctrl.h>
> + Integers values in "pinmux" argument list are assembled as:
> + ((PORT * 16 + PIN) | MUX_FUNC << 16)
> +
> + phandle: true
> + input-enable: true
> + output-enable: true
> +
> + required:
> + - pinmux
> +
> + additionalProperties: false
> +
> + - type: object
> + properties:
> + phandle: true
> +
> + additionalProperties:
> + $ref: "#/additionalProperties/anyOf/0"
> +
> +examples:
> + - |
> + #include <dt-bindings/pinctrl/r7s72100-pinctrl.h>
> + pinctrl: pinctrl@fcfe3000 {
> + compatible = "renesas,r7s72100-ports";
> +
> + reg = <0xfcfe3000 0x4230>;
> +
> + /*
> + * A GPIO controller node, controlling 16 pins indexed from 0.
> + * The GPIO controller base in the global pin indexing space is pin
> + * 48, thus pins [0 - 15] on this controller map to pins [48 - 63]
> + * in the global pin indexing space.
> + */
> + port3: gpio-3 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pinctrl 0 48 16>;
> + };
> +
> + /*
> + * A serial communication interface with a TX output pin and an RX
> + * input pin.
> + * Pin #0 on port #3 is configured as alternate function #6.
> + * Pin #2 on port #3 is configured as alternate function #4.
> + */
> + scif2_pins: serial2 {
> + pinmux = <RZA1_PINMUX(3, 0, 6)>, <RZA1_PINMUX(3, 2, 4)>;
> + };
> +
> +
> + /*
> + * I2c master: both SDA and SCL pins need bi-directional operations
> + * Pin #4 on port #1 is configured as alternate function #1.
> + * Pin #5 on port #1 is configured as alternate function #1.
> + * Both need to work in bi-directional mode, the driver must manage
> + * this internally.
> + */
> + i2c2_pins: i2c2 {
> + pinmux = <RZA1_PINMUX(1, 4, 1)>, <RZA1_PINMUX(1, 5, 1)>;
> + };
> +
> +
> + /*
> + * Multi-function timer input and output compare pins.
> + */
> + tioc0_pins: tioc0 {
> + /*
> + * Configure TIOC0A as software driven input
> + * Pin #0 on port #4 is configured as alternate function #2
> + * with IO direction specified by software as input.
> + */
> + tioc0_input_pins {
> + pinmux = <RZA1_PINMUX(4, 0, 2)>;
> + input-enable;
> + };
> +
> + /*
> + * Configure TIOC0B as software driven output
> + * Pin #1 on port #4 is configured as alternate function #1
> + * with IO direction specified by software as output.
> + */
> + tioc0_output_pins {
> + pinmux = <RZA1_PINMUX(4, 1, 1)>;
> + output-enable;
> + };
> + };
> + };
> --
> 2.17.1
>
Re: [PATCH] dt-bindings: pinctrl: rza1: Convert to json-schema
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: Re: [PATCH] dt-bindings: pinctrl: rza1: Convert to json-schema
- From: Jacopo Mondi <jacopo@xxxxxxxxxx>
- Date: Mon, 24 Aug 2020 11:13:40 +0200
- In-reply-to: <20200821111956.4989-1-geert+renesas@glider.be>
- References: <20200821111956.4989-1-geert+renesas@glider.be>
- Follow-Ups:
- Re: [PATCH] dt-bindings: pinctrl: rza1: Convert to json-schema
- From: Geert Uytterhoeven
- Re: [PATCH] dt-bindings: pinctrl: rza1: Convert to json-schema
- References:
- [PATCH] dt-bindings: pinctrl: rza1: Convert to json-schema
- From: Geert Uytterhoeven
- [PATCH] dt-bindings: pinctrl: rza1: Convert to json-schema
- Prev by Date: RE: [PATCH 21/22] arm64: dts: imx8qxp: Remove i.MX7 compatible from USDHC
- Next by Date: Re: [PATCH 21/22] arm64: dts: imx8qxp: Remove i.MX7 compatible from USDHC
- Previous by thread: [PATCH] dt-bindings: pinctrl: rza1: Convert to json-schema
- Next by thread: Re: [PATCH] dt-bindings: pinctrl: rza1: Convert to json-schema
- Index(es):
 |