Re: [PATCH v2 0/2] Add GPIO level-sensitive interrupt support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2/19/20 10:20 AM, Alexandre Torgue wrote:
Hi,
[...]
>>>>> This series adds the possibility to handle gpio interrupts on level.
>>>>>
>>>>> GPIO hardware block is directly linked to EXTI block but EXTI handles
>>>>> external interrupts only on edge. To be able to handle GPIO
>>>>> interrupt on
>>>>> level a "hack" is done in gpio irq chip: parent interrupt (exti irq
>>>>> chip)
>>>>> is retriggered following interrupt type and gpio line value.
>>>>>
>>>>> In exti irq chip, retrigger ops function is added.
>>>>
>>>> btw. this might be unrelated, but is it possible to have e.g. gpioC2
>>>> set
>>>> as trigger-level-low and gpioD2 set as trigger-edge-falling ? It seems
>>>> 8eb2dfee9fb1 ("pinctrl: stm32: add lock mechanism for irqmux
>>>> selection")
>>>> prevents that.
>>>>
>>>
>>> No it's not possible. Each gpio line doesn't have a dedicated Exti line
>>> Each Exti line is muxing between gpio banks.
>>
>> OK, that confirms my assumption.
>>
>>> Mapping is done as following:
>>>
>>> EXTI0 = A0 or B0 or C0 .... or Z0 : selected by Mux
>>> EXTI1 = A1 or B1 or C1 ....or Z1 : selected by Mux
>>> EXTI2 = A2 or B2 or C2 ....or Z2 : selected by Mux
>>> ...
>>
>> Is it at least possible to have IRQs of the same type on the same exti
>> line? E.g. gpioA2 of trigger-edge-falling and gpioB2
>> trigger-edge-falling ?
>>
> 
> Sorry I don't catch your point. If you already succeed to get gpioA2,
> then you will failed to get gpioB2 but looking at function call stack we
> could get an other issue.

Considering the EXTI line limitations, I'd like to know what kind of IRQ
input configuration is allowed/valid and what kind of configuration is
not valid.

> Lets take example where you succeed to get gpioa2 as interrupt (using
> interrupt bindings) and now you try to do the same for gpiob2, you will
> have (roughly):
> 
> stm32_gpio_irq_request_resources (for gpiob2) --> succeed
> 
> stm32_gpio_set_type
>  |
>  |--> stm32_exti_set_type type -> change exti line 2 trigger registers
>                                   with gpiob2 binding.
> 
> stm32_gpio_domain_activate --> failed as exti line2 is already used
>                    by gpioa2.
> 
> So as stm32_gpio_set_type is called before checking than exti line is
> available, type could be changed and behavior of gpioa2 interrupt broken.
> 
> Solution would be to move the exti line mux check from
> stm32_gpio_domain_activate to  stm32_gpio_irq_request_resources callback.

So the hardware does support using both gpioA2 and gpioB2 as an
interrupt source, for different drivers, if they are of the same
interrupt type. Except the current implementation does not permit that.

If the interrupt types are different, that is not supported by the hardware.

Correct ?



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux