Re: [PATCH v4] gpio: winbond: add driver

[Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>]

On Thu, 2018-01-04 at 22:46 +0100, Maciej S. Szmigiero wrote:
> This commit adds GPIO driver for Winbond Super I/Os.
> 
> Currently, only W83627UHG model (also known as Nuvoton NCT6627UD) is
> supported but in the future a support for other Winbond models, too,
> can
> be added to the driver.
> 
> A module parameter "gpios" sets a bitmask of GPIO ports to enable (bit
> 0 is
> GPIO1, bit 1 is GPIO2, etc.).
> One should be careful which ports one tinkers with since some might be
> managed by the firmware (for functions like powering on and off,
> sleeping,
> BIOS recovery, etc.) and some of GPIO port pins are physically shared
> with
> other devices included in the Super I/O chip.
> 

I still have an impression that it could be MFD based driver will all
infrastructure needed for the actual devices behind, though here is an
objection from the author, so, I leave it to maintainers.

Besides that I don't like global variables in so many amount (perhaps
custom struct gpio_w83227uhg {...};  static struct ... *...; might
improve this.

And one nit below.

So, there is room for improvement for my opinion, anyway, FWIW,

Reviewed-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>

> Signed-off-by: Maciej S. Szmigiero <mail@xxxxxxxxxxxxxxxxxxxxx>
> ---
> Changes from v1:
> * Added SPDX license tag,
> 
> * Removed gpiobase parameter,
> 
> * Changed uint{8,16}_t types to u{8,16},
> 
> * Added kerneldoc descriptions of driver structures,
> 
> * Reformatted winbond_gpio_infos array fields so they are on separate
> lines,
> 
> * Added few comments here and there as requested,
> 
> * Moved port configuration code from separate
> winbond_gpio_configure_X()
> functions to one, common, parametrized winbond_gpio_configure_port()
> function.
> 
> Changes from v2:
> * Adapted the driver to use the ISA bus instead of the platform one,
> 
> * Reformatted register and register bit macros,
> 
> * Added wb_sio_{notice,warn,err} macros to not repeat pr_* calls with
> the same prefix again and again,
> 
> * Added a comment why a double I/O register write is needed,
> 
> * Converted the code to use for_each_set_bit() where it could be used,
> 
> * Removed a warning about an impossible condition in
> winbond_gpio_get_info(),
> 
> * Made winbond_gpio_get_info() return a reduced GPIO number,
> 
> * Renamed gpiolib callback functions parameter name from gpio_num to
> offset,
> 
> * Changed I/O port number variables to unsigned long type,
> 
> * Removed explicit casts in logging calls,
> 
> * hweight() is now used for calculating the total GPIO count.
> 
> Changes from v3:
> * Changed the code to use pr_fmt(x) instead of
> wb_sio_{notice,warn,err}
> logging macros,
> 
> * Made the driver warn about but accept extra bits in the "gpios"
> parameter,
> 
> * Removed a one case of a redundant 'else',
> 
> * Swapped a one missed pair of register bit macros,
> 
> * Changed the code to pass a size in bits, not bytes, to
> for_each_set_bit() macros.
> 
>  drivers/gpio/Kconfig        |  16 +
>  drivers/gpio/Makefile       |   1 +
>  drivers/gpio/gpio-winbond.c | 723
> ++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 740 insertions(+)
>  create mode 100644 drivers/gpio/gpio-winbond.c
> 
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index 395669bfcc26..8c4018855c3b 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -698,6 +698,22 @@ config GPIO_TS5500
>  	  blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the
> TS-5600
>  	  LCD port.
>  
> +config GPIO_WINBOND
> +	tristate "Winbond Super I/O GPIO support"
> +	select ISA_BUS_API
> +	help
> +	  This option enables support for GPIOs found on Winbond
> Super I/O
> +	  chips.
> +	  Currently, only W83627UHG (also known as Nuvoton NCT6627UD)
> is
> +	  supported.
> +
> +	  You will need to provide a module parameter "gpios", or a
> +	  boot-time parameter "gpio_winbond.gpios" with a bitmask of
> GPIO
> +	  ports to enable (bit 0 is GPIO1, bit 1 is GPIO2, etc.).
> +
> +	  To compile this driver as a module, choose M here: the
> module will
> +	  be called gpio-winbond.
> +
>  config GPIO_WS16C48
>  	tristate "WinSystems WS16C48 GPIO support"
>  	depends on ISA_BUS_API
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index bc5dd673fa11..ff3d36d0a443 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -139,6 +139,7 @@ obj-$(CONFIG_GPIO_VIPERBOARD)	+= gpio-
> viperboard.o
>  obj-$(CONFIG_GPIO_VR41XX)	+= gpio-vr41xx.o
>  obj-$(CONFIG_GPIO_VX855)	+= gpio-vx855.o
>  obj-$(CONFIG_GPIO_WHISKEY_COVE)	+= gpio-wcove.o
> +obj-$(CONFIG_GPIO_WINBOND)	+= gpio-winbond.o
>  obj-$(CONFIG_GPIO_WM831X)	+= gpio-wm831x.o
>  obj-$(CONFIG_GPIO_WM8350)	+= gpio-wm8350.o
>  obj-$(CONFIG_GPIO_WM8994)	+= gpio-wm8994.o
> diff --git a/drivers/gpio/gpio-winbond.c b/drivers/gpio/gpio-winbond.c
> new file mode 100644
> index 000000000000..a06a47f3dcdf
> --- /dev/null
> +++ b/drivers/gpio/gpio-winbond.c
> @@ -0,0 +1,723 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * GPIO interface for Winbond Super I/O chips
> + * Currently, only W83627UHG (Nuvoton NCT6627UD) is supported.
> + *
> + * Author: Maciej S. Szmigiero <mail@xxxxxxxxxxxxxxxxxxxxx>
> + */
> +
> +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> +
> +#include <linux/gpio/driver.h>
> +#include <linux/ioport.h>
> +#include <linux/isa.h>
> +#include <linux/module.h>
> +
> +#define WB_GPIO_DRIVER_NAME		KBUILD_MODNAME
> +
> +#define WB_SIO_BASE			0x2e
> +#define WB_SIO_BASE_HIGH		0x4e
> +
> +#define WB_SIO_EXT_ENTER_KEY		0x87
> +#define WB_SIO_EXT_EXIT_KEY		0xaa
> +
> +/* global chip registers */
> +
> +#define WB_SIO_REG_LOGICAL		0x07
> +
> +#define WB_SIO_REG_CHIP_MSB		0x20
> +#define WB_SIO_REG_CHIP_LSB		0x21
> +
> +#define WB_SIO_CHIP_ID_W83627UHG	0xa230
> +#define WB_SIO_CHIP_ID_W83627UHG_MASK	GENMASK(15, 4)
> +
> +#define WB_SIO_REG_DPD			0x22
> +#define WB_SIO_REG_DPD_UARTA		4
> +#define WB_SIO_REG_DPD_UARTB		5
> +
> +#define WB_SIO_REG_IDPD		0x23
> +#define WB_SIO_REG_IDPD_UARTC		4
> +#define WB_SIO_REG_IDPD_UARTD		5
> +#define WB_SIO_REG_IDPD_UARTE		6
> +#define WB_SIO_REG_IDPD_UARTF		7
> +
> +#define WB_SIO_REG_GLOBAL_OPT		0x24
> +#define WB_SIO_REG_GO_ENFDC		1
> +
> +#define WB_SIO_REG_OVTGPIO3456		0x29
> +#define WB_SIO_REG_OG3456_G3PP		3
> +#define WB_SIO_REG_OG3456_G4PP		4
> +#define WB_SIO_REG_OG3456_G5PP		5
> +#define WB_SIO_REG_OG3456_G6PP		7
> +
> +#define WB_SIO_REG_I2C_PS		0x2a
> +#define WB_SIO_REG_I2CPS_I2CFS		1
> +
> +#define WB_SIO_REG_GPIO1_MF		0x2c
> +#define WB_SIO_REG_G1MF_G1PP		6
> +#define WB_SIO_REG_G1MF_G2PP		7
> +#define WB_SIO_REG_G1MF_FS_MASK	GENMASK(1, 0)
> +#define WB_SIO_REG_G1MF_FS_IR_OFF	0
> +#define WB_SIO_REG_G1MF_FS_IR		1
> +#define WB_SIO_REG_G1MF_FS_GPIO1	2
> +#define WB_SIO_REG_G1MF_FS_UARTB	3
> +
> +/* not an actual device number, just a value meaning 'no device' */
> +#define WB_SIO_DEV_NONE		0xff
> +
> +/* registers with offsets >= 0x30 are specific for a particular
> device */
> +
> +/* UART B logical device */
> +#define WB_SIO_DEV_UARTB		0x03
> +#define WB_SIO_UARTB_REG_ENABLE	0x30
> +#define WB_SIO_UARTB_ENABLE_ON		0
> +
> +/* UART C logical device */
> +#define WB_SIO_DEV_UARTC		0x06
> +#define WB_SIO_UARTC_REG_ENABLE	0x30
> +#define WB_SIO_UARTC_ENABLE_ON		0
> +
> +/* GPIO3, GPIO4 logical device */
> +#define WB_SIO_DEV_GPIO34		0x07
> +#define WB_SIO_GPIO34_REG_ENABLE	0x30
> +#define WB_SIO_GPIO34_ENABLE_3		0
> +#define WB_SIO_GPIO34_ENABLE_4		1
> +#define WB_SIO_GPIO34_REG_IO3		0xe0
> +#define WB_SIO_GPIO34_REG_DATA3	0xe1
> +#define WB_SIO_GPIO34_REG_INV3		0xe2
> +#define WB_SIO_GPIO34_REG_IO4		0xe4
> +#define WB_SIO_GPIO34_REG_DATA4	0xe5
> +#define WB_SIO_GPIO34_REG_INV4		0xe6
> +
> +/* WDTO, PLED, GPIO5, GPIO6 logical device */
> +#define WB_SIO_DEV_WDGPIO56		0x08
> +#define WB_SIO_WDGPIO56_REG_ENABLE	0x30
> +#define WB_SIO_WDGPIO56_ENABLE_5	1
> +#define WB_SIO_WDGPIO56_ENABLE_6	2
> +#define WB_SIO_WDGPIO56_REG_IO5	0xe0
> +#define WB_SIO_WDGPIO56_REG_DATA5	0xe1
> +#define WB_SIO_WDGPIO56_REG_INV5	0xe2
> +#define WB_SIO_WDGPIO56_REG_IO6	0xe4
> +#define WB_SIO_WDGPIO56_REG_DATA6	0xe5
> +#define WB_SIO_WDGPIO56_REG_INV6	0xe6
> +
> +/* GPIO1, GPIO2, SUSLED logical device */
> +#define WB_SIO_DEV_GPIO12		0x09
> +#define WB_SIO_GPIO12_REG_ENABLE	0x30
> +#define WB_SIO_GPIO12_ENABLE_1		0
> +#define WB_SIO_GPIO12_ENABLE_2		1
> +#define WB_SIO_GPIO12_REG_IO1		0xe0
> +#define WB_SIO_GPIO12_REG_DATA1	0xe1
> +#define WB_SIO_GPIO12_REG_INV1		0xe2
> +#define WB_SIO_GPIO12_REG_IO2		0xe4
> +#define WB_SIO_GPIO12_REG_DATA2	0xe5
> +#define WB_SIO_GPIO12_REG_INV2		0xe6
> +
> +/* UART D logical device */
> +#define WB_SIO_DEV_UARTD		0x0d
> +#define WB_SIO_UARTD_REG_ENABLE	0x30
> +#define WB_SIO_UARTD_ENABLE_ON		0
> +
> +/* UART E logical device */
> +#define WB_SIO_DEV_UARTE		0x0e
> +#define WB_SIO_UARTE_REG_ENABLE	0x30
> +#define WB_SIO_UARTE_ENABLE_ON		0
> +
> +static unsigned long baseparam;
> +static unsigned long gpios;
> +static unsigned long ppgpios;
> +static unsigned long odgpios;
> +static bool pledgpio;
> +static bool beepgpio;
> +static bool i2cgpio;
> +
> +static int winbond_sio_enter(unsigned long base)
> +{
> +	if (!request_muxed_region(base, 2, WB_GPIO_DRIVER_NAME))
> +		return -EBUSY;
> +
> +	/*
> +	 * datasheet says two successive writes of the "key" value
> are needed
> +	 * in order for chip to enter the "Extended Function Mode"
> +	 */
> +	outb(WB_SIO_EXT_ENTER_KEY, base);
> +	outb(WB_SIO_EXT_ENTER_KEY, base);
> +
> +	return 0;
> +}
> +
> +static void winbond_sio_select_logical(unsigned long base, u8 dev)
> +{
> +	outb(WB_SIO_REG_LOGICAL, base);
> +	outb(dev, base + 1);
> +}
> +
> +static void winbond_sio_leave(unsigned long base)
> +{
> +	outb(WB_SIO_EXT_EXIT_KEY, base);
> +
> +	release_region(base, 2);
> +}
> +
> +static void winbond_sio_reg_write(unsigned long base, u8 reg, u8
> data)
> +{
> +	outb(reg, base);
> +	outb(data, base + 1);
> +}
> +
> +static u8 winbond_sio_reg_read(unsigned long base, u8 reg)
> +{
> +	outb(reg, base);
> +	return inb(base + 1);
> +}
> +
> +static void winbond_sio_reg_bset(unsigned long base, u8 reg, u8 bit)
> +{
> +	u8 val;
> +
> +	val = winbond_sio_reg_read(base, reg);
> +	val |= BIT(bit);
> +	winbond_sio_reg_write(base, reg, val);
> +}
> +
> +static void winbond_sio_reg_bclear(unsigned long base, u8 reg, u8
> bit)
> +{
> +	u8 val;
> +
> +	val = winbond_sio_reg_read(base, reg);
> +	val &= ~BIT(bit);
> +	winbond_sio_reg_write(base, reg, val);
> +}
> +
> +static bool winbond_sio_reg_btest(unsigned long base, u8 reg, u8 bit)
> +{
> +	return winbond_sio_reg_read(base, reg) & BIT(bit);
> +}
> +
> +/**
> + * struct winbond_gpio_port_conflict - possibly conflicting device
> information
> + * @name:	device name (NULL means no conflicting device
> defined)
> + * @dev:	Super I/O logical device number where the testreg
> register
> + *		is located (or WB_SIO_DEV_NONE - don't select any
> + *		logical device)
> + * @testreg:	register number where the testbit bit is located
> + * @testbit:	index of a bit to check whether an actual
> conflict exists
> + * @warnonly:	if set then a conflict isn't fatal (just warn
> about it),
> + *		otherwise disable the particular GPIO port if a
> conflict
> + *		is detected
> + */
> +struct winbond_gpio_port_conflict {
> +	const char *name;
> +	u8 dev;
> +	u8 testreg;
> +	u8 testbit;
> +	bool warnonly;
> +};
> +
> +/**
> + * struct winbond_gpio_info - information about a particular GPIO
> port (device)
> + * @dev:		Super I/O logical device number of the
> registers
> + *			specified below
> + * @enablereg:		port enable bit register number
> + * @enablebit:		index of a port enable bit
> + * @outputreg:		output driver mode bit register number
> + * @outputppbit:	index of a push-pull output driver mode bit
> + * @ioreg:		data direction register number
> + * @invreg:		pin data inversion register number
> + * @datareg:		pin data register number
> + * @conflict:		description of a device that possibly
> conflicts with
> + *			this port
> + */
> +struct winbond_gpio_info {
> +	u8 dev;
> +	u8 enablereg;
> +	u8 enablebit;
> +	u8 outputreg;
> +	u8 outputppbit;
> +	u8 ioreg;
> +	u8 invreg;
> +	u8 datareg;
> +	struct winbond_gpio_port_conflict conflict;
> +};
> +
> +static const struct winbond_gpio_info winbond_gpio_infos[6] = {
> +	{ /* 0 */
> +		.dev = WB_SIO_DEV_GPIO12,
> +		.enablereg = WB_SIO_GPIO12_REG_ENABLE,
> +		.enablebit = WB_SIO_GPIO12_ENABLE_1,
> +		.outputreg = WB_SIO_REG_GPIO1_MF,
> +		.outputppbit = WB_SIO_REG_G1MF_G1PP,
> +		.ioreg = WB_SIO_GPIO12_REG_IO1,
> +		.invreg = WB_SIO_GPIO12_REG_INV1,
> +		.datareg = WB_SIO_GPIO12_REG_DATA1,
> +		.conflict = {
> +			.name = "UARTB",
> +			.dev = WB_SIO_DEV_UARTB,
> +			.testreg = WB_SIO_UARTB_REG_ENABLE,
> +			.testbit = WB_SIO_UARTB_ENABLE_ON,
> +			.warnonly = true
> +		}
> +	},
> +	{ /* 1 */
> +		.dev = WB_SIO_DEV_GPIO12,
> +		.enablereg = WB_SIO_GPIO12_REG_ENABLE,
> +		.enablebit = WB_SIO_GPIO12_ENABLE_2,
> +		.outputreg = WB_SIO_REG_GPIO1_MF,
> +		.outputppbit = WB_SIO_REG_G1MF_G2PP,
> +		.ioreg = WB_SIO_GPIO12_REG_IO2,
> +		.invreg = WB_SIO_GPIO12_REG_INV2,
> +		.datareg = WB_SIO_GPIO12_REG_DATA2
> +		/* special conflict handling so doesn't use conflict
> data */
> +	},
> +	{ /* 2 */
> +		.dev = WB_SIO_DEV_GPIO34,
> +		.enablereg = WB_SIO_GPIO34_REG_ENABLE,
> +		.enablebit = WB_SIO_GPIO34_ENABLE_3,
> +		.outputreg = WB_SIO_REG_OVTGPIO3456,
> +		.outputppbit = WB_SIO_REG_OG3456_G3PP,
> +		.ioreg = WB_SIO_GPIO34_REG_IO3,
> +		.invreg = WB_SIO_GPIO34_REG_INV3,
> +		.datareg = WB_SIO_GPIO34_REG_DATA3,
> +		.conflict = {
> +			.name = "UARTC",
> +			.dev = WB_SIO_DEV_UARTC,
> +			.testreg = WB_SIO_UARTC_REG_ENABLE,
> +			.testbit = WB_SIO_UARTC_ENABLE_ON,
> +			.warnonly = true
> +		}
> +	},
> +	{ /* 3 */
> +		.dev = WB_SIO_DEV_GPIO34,
> +		.enablereg = WB_SIO_GPIO34_REG_ENABLE,
> +		.enablebit = WB_SIO_GPIO34_ENABLE_4,
> +		.outputreg = WB_SIO_REG_OVTGPIO3456,
> +		.outputppbit = WB_SIO_REG_OG3456_G4PP,
> +		.ioreg = WB_SIO_GPIO34_REG_IO4,
> +		.invreg = WB_SIO_GPIO34_REG_INV4,
> +		.datareg = WB_SIO_GPIO34_REG_DATA4,
> +		.conflict = {
> +			.name = "UARTD",
> +			.dev = WB_SIO_DEV_UARTD,
> +			.testreg = WB_SIO_UARTD_REG_ENABLE,
> +			.testbit = WB_SIO_UARTD_ENABLE_ON,
> +			.warnonly = true
> +		}
> +	},
> +	{ /* 4 */
> +		.dev = WB_SIO_DEV_WDGPIO56,
> +		.enablereg = WB_SIO_WDGPIO56_REG_ENABLE,
> +		.enablebit = WB_SIO_WDGPIO56_ENABLE_5,
> +		.outputreg = WB_SIO_REG_OVTGPIO3456,
> +		.outputppbit = WB_SIO_REG_OG3456_G5PP,
> +		.ioreg = WB_SIO_WDGPIO56_REG_IO5,
> +		.invreg = WB_SIO_WDGPIO56_REG_INV5,
> +		.datareg = WB_SIO_WDGPIO56_REG_DATA5,
> +		.conflict = {
> +			.name = "UARTE",
> +			.dev = WB_SIO_DEV_UARTE,
> +			.testreg = WB_SIO_UARTE_REG_ENABLE,
> +			.testbit = WB_SIO_UARTE_ENABLE_ON,
> +			.warnonly = true
> +		}
> +	},
> +	{ /* 5 */
> +		.dev = WB_SIO_DEV_WDGPIO56,
> +		.enablereg = WB_SIO_WDGPIO56_REG_ENABLE,
> +		.enablebit = WB_SIO_WDGPIO56_ENABLE_6,
> +		.outputreg = WB_SIO_REG_OVTGPIO3456,
> +		.outputppbit = WB_SIO_REG_OG3456_G6PP,
> +		.ioreg = WB_SIO_WDGPIO56_REG_IO6,
> +		.invreg = WB_SIO_WDGPIO56_REG_INV6,
> +		.datareg = WB_SIO_WDGPIO56_REG_DATA6,
> +		.conflict = {
> +			.name = "FDC",
> +			.dev = WB_SIO_DEV_NONE,
> +			.testreg = WB_SIO_REG_GLOBAL_OPT,
> +			.testbit = WB_SIO_REG_GO_ENFDC,
> +			.warnonly = false
> +		}
> +	}
> +};
> +
> +/* returns whether changing a pin is allowed */
> +static bool winbond_gpio_get_info(unsigned int *gpio_num,
> +				  const struct winbond_gpio_info
> **info)
> +{
> +	bool allow_changing = true;
> +	unsigned long i;
> +
> +	for_each_set_bit(i, &gpios, BITS_PER_LONG) {
> +		if (*gpio_num < 8)
> +			break;
> +
> +		*gpio_num -= 8;
> +	}
> +
> +	*info = &winbond_gpio_infos[i];
> +
> +	/*
> +	 * GPIO2 (the second port) shares some pins with a basic PC
> +	 * functionality, which is very likely controlled by the
> firmware.
> +	 * Don't allow changing these pins by default.
> +	 */
> +	if (i == 1) {
> +		if (*gpio_num == 0 && !pledgpio)
> +			allow_changing = false;
> +		else if (*gpio_num == 1 && !beepgpio)
> +			allow_changing = false;
> +		else if ((*gpio_num == 5 || *gpio_num == 6) &&
> !i2cgpio)
> +			allow_changing = false;
> +	}
> +
> +	return allow_changing;
> +}
> +
> +static int winbond_gpio_get(struct gpio_chip *gc, unsigned int
> offset)
> +{
> +	unsigned long *base = gpiochip_get_data(gc);
> +	const struct winbond_gpio_info *info;
> +	bool val;
> +
> +	winbond_gpio_get_info(&offset, &info);
> +
> +	val = winbond_sio_enter(*base);
> +	if (val)
> +		return val;
> +
> +	winbond_sio_select_logical(*base, info->dev);
> +
> +	val = winbond_sio_reg_btest(*base, info->datareg, offset);
> +	if (winbond_sio_reg_btest(*base, info->invreg, offset))
> +		val = !val;
> +
> +	winbond_sio_leave(*base);
> +
> +	return val;
> +}
> +
> +static int winbond_gpio_direction_in(struct gpio_chip *gc, unsigned
> int offset)
> +{
> +	unsigned long *base = gpiochip_get_data(gc);
> +	const struct winbond_gpio_info *info;
> +	int ret;
> +
> +	if (!winbond_gpio_get_info(&offset, &info))
> +		return -EACCES;
> +
> +	ret = winbond_sio_enter(*base);
> +	if (ret)
> +		return ret;
> +
> +	winbond_sio_select_logical(*base, info->dev);
> +
> +	winbond_sio_reg_bset(*base, info->ioreg, offset);
> +
> +	winbond_sio_leave(*base);
> +
> +	return 0;
> +}
> +
> +static int winbond_gpio_direction_out(struct gpio_chip *gc,
> +				      unsigned int offset,
> +				      int val)
> +{
> +	unsigned long *base = gpiochip_get_data(gc);
> +	const struct winbond_gpio_info *info;
> +	int ret;
> +
> +	if (!winbond_gpio_get_info(&offset, &info))
> +		return -EACCES;
> +
> +	ret = winbond_sio_enter(*base);
> +	if (ret)
> +		return ret;
> +
> +	winbond_sio_select_logical(*base, info->dev);
> +
> +	winbond_sio_reg_bclear(*base, info->ioreg, offset);
> +
> +	if (winbond_sio_reg_btest(*base, info->invreg, offset))
> +		val = !val;
> +
> +	if (val)
> +		winbond_sio_reg_bset(*base, info->datareg, offset);
> +	else
> +		winbond_sio_reg_bclear(*base, info->datareg, offset);
> +
> +	winbond_sio_leave(*base);
> +
> +	return 0;
> +}
> +
> +static void winbond_gpio_set(struct gpio_chip *gc, unsigned int
> offset,
> +			     int val)
> +{
> +	unsigned long *base = gpiochip_get_data(gc);
> +	const struct winbond_gpio_info *info;
> +
> +	if (!winbond_gpio_get_info(&offset, &info))
> +		return;
> +
> +	if (winbond_sio_enter(*base) != 0)
> +		return;
> +
> +	winbond_sio_select_logical(*base, info->dev);
> +
> +	if (winbond_sio_reg_btest(*base, info->invreg, offset))
> +		val = !val;
> +
> +	if (val)
> +		winbond_sio_reg_bset(*base, info->datareg, offset);
> +	else
> +		winbond_sio_reg_bclear(*base, info->datareg, offset);
> +
> +	winbond_sio_leave(*base);
> +}
> +
> +static struct gpio_chip winbond_gpio_chip = {
> +	.base			= -1,
> +	.label			= WB_GPIO_DRIVER_NAME,
> +	.owner			= THIS_MODULE,
> +	.can_sleep		= true,
> +	.get			= winbond_gpio_get,
> +	.direction_input	= winbond_gpio_direction_in,
> +	.set			= winbond_gpio_set,
> +	.direction_output	= winbond_gpio_direction_out,
> +};
> +
> +static void winbond_gpio_configure_port0_pins(unsigned long base)
> +{
> +	unsigned int val;
> +
> +	val = winbond_sio_reg_read(base, WB_SIO_REG_GPIO1_MF);
> +	if ((val & WB_SIO_REG_G1MF_FS_MASK) ==
> WB_SIO_REG_G1MF_FS_GPIO1)
> +		return;
> +
> +	pr_warn("GPIO1 pins were connected to something else (%.2x),
> fixing\n",
> +		val);
> +
> +	val &= ~WB_SIO_REG_G1MF_FS_MASK;
> +	val |= WB_SIO_REG_G1MF_FS_GPIO1;
> +
> +	winbond_sio_reg_write(base, WB_SIO_REG_GPIO1_MF, val);
> +}
> +
> +static void winbond_gpio_configure_port1_check_i2c(unsigned long
> base)
> +{
> +	i2cgpio = !winbond_sio_reg_btest(base, WB_SIO_REG_I2C_PS,
> +					 WB_SIO_REG_I2CPS_I2CFS);
> +	if (!i2cgpio)
> +		pr_warn("disabling GPIO2.5 and GPIO2.6 as I2C is
> enabled\n");
> +}
> +
> +static bool winbond_gpio_configure_port(unsigned long base, unsigned
> int idx)
> +{
> +	const struct winbond_gpio_info *info =
> &winbond_gpio_infos[idx];
> +	const struct winbond_gpio_port_conflict *conflict = &info-
> >conflict;
> +
> +	/* is there a possible conflicting device defined? */
> +	if (conflict->name != NULL) {
> +		if (conflict->dev != WB_SIO_DEV_NONE)
> +			winbond_sio_select_logical(base, conflict-
> >dev);
> +
> +		if (winbond_sio_reg_btest(base, conflict->testreg,
> +					  conflict->testbit)) {
> +			if (conflict->warnonly)
> +				pr_warn("enabled GPIO%u share pins
> with active %s\n",
> +					idx + 1, conflict->name);
> +			else {
> +				pr_warn("disabling GPIO%u as %s is
> enabled\n",
> +					idx + 1, conflict->name);
> +				return false;
> +			}
> +		}
> +	}
> +
> +	/* GPIO1 and GPIO2 need some (additional) special handling */
> +	if (idx == 0)
> +		winbond_gpio_configure_port0_pins(base);
> +	else if (idx == 1)
> +		winbond_gpio_configure_port1_check_i2c(base);
> +
> +	winbond_sio_select_logical(base, info->dev);
> +
> +	winbond_sio_reg_bset(base, info->enablereg, info->enablebit);
> +
> +	if (ppgpios & BIT(idx))
> +		winbond_sio_reg_bset(base, info->outputreg,
> +				     info->outputppbit);
> +	else if (odgpios & BIT(idx))
> +		winbond_sio_reg_bclear(base, info->outputreg,
> +				       info->outputppbit);
> +	else
> +		pr_notice("GPIO%u pins are %s\n", idx + 1,
> +			  winbond_sio_reg_btest(base, info-
> >outputreg,
> +						info->outputppbit) ?
> +			  "push-pull" :
> +			  "open drain");
> +
> +	return true;
> +}
> +
> +static int winbond_gpio_configure(unsigned long base)
> +{
> +	unsigned long i;
> +
> +	for_each_set_bit(i, &gpios, BITS_PER_LONG)
> +		if (!winbond_gpio_configure_port(base, i))

> +			gpios &= ~BIT(i);

It might be __clear_bit(i, &gpios); as well.

> +
> +	if (!gpios) {
> +		pr_err("please use 'gpios' module parameter to select
> some active GPIO ports to enable\n");
> +		return -EINVAL;
> +	}
> +
> +	return 0;
> +}
> +
> +static int winbond_gpio_check_chip(unsigned long base)
> +{
> +	int ret;
> +	unsigned int chip;
> +
> +	ret = winbond_sio_enter(base);
> +	if (ret)
> +		return ret;
> +
> +	chip = winbond_sio_reg_read(base, WB_SIO_REG_CHIP_MSB) << 8;
> +	chip |= winbond_sio_reg_read(base, WB_SIO_REG_CHIP_LSB);
> +
> +	pr_notice("chip ID at %lx is %.4x\n", base, chip);
> +
> +	if ((chip & WB_SIO_CHIP_ID_W83627UHG_MASK) !=
> +	    WB_SIO_CHIP_ID_W83627UHG) {
> +		pr_err("not an our chip\n");
> +		ret = -ENODEV;
> +	}
> +
> +	winbond_sio_leave(base);
> +
> +	return ret;
> +}
> +
> +static int winbond_gpio_imatch(struct device *dev, unsigned int id)
> +{
> +	unsigned long gpios_rem;
> +	int ret;
> +
> +	gpios_rem = gpios & ~GENMASK(ARRAY_SIZE(winbond_gpio_infos) -
> 1, 0);
> +	if (gpios_rem) {
> +		pr_warn("unknown ports (%lx) enabled in GPIO ports
> bitmask\n",
> +			gpios_rem);
> +		gpios &= ~gpios_rem;
> +	}
> +
> +	if (ppgpios & odgpios) {
> +		pr_err("some GPIO ports are set both to push-pull and
> open drain mode at the same time\n");
> +		return 0;
> +	}
> +
> +	if (baseparam != 0)
> +		return winbond_gpio_check_chip(baseparam) == 0;
> +
> +	/*
> +	 * if the 'base' module parameter is unset probe two chip
> default
> +	 * I/O port bases
> +	 */
> +	baseparam = WB_SIO_BASE;
> +	ret = winbond_gpio_check_chip(baseparam);
> +	if (ret == 0)
> +		return 1;
> +	if (ret != -ENODEV && ret != -EBUSY)
> +		return 0;
> +
> +	baseparam = WB_SIO_BASE_HIGH;
> +	return winbond_gpio_check_chip(baseparam) == 0;
> +}
> +
> +static int winbond_gpio_iprobe(struct device *dev, unsigned int id)
> +{
> +	int ret;
> +
> +	if (baseparam == 0)
> +		return -EINVAL;
> +
> +	ret = winbond_sio_enter(baseparam);
> +	if (ret)
> +		return ret;
> +
> +	ret = winbond_gpio_configure(baseparam);
> +
> +	winbond_sio_leave(baseparam);
> +
> +	if (ret)
> +		return ret;
> +
> +	/*
> +	 * Add 8 gpios for every GPIO port that was enabled in gpios
> +	 * module parameter (that wasn't disabled earlier in
> +	 * winbond_gpio_configure() & co. due to, for example, a pin
> conflict).
> +	 */
> +	winbond_gpio_chip.ngpio = hweight_long(gpios) * 8;
> +
> +	/*
> +	 * GPIO6 port has only 5 pins, so if it is enabled we have to
> adjust
> +	 * the total count appropriately
> +	 */
> +	if (gpios & BIT(5))
> +		winbond_gpio_chip.ngpio -= (8 - 5);
> +
> +	winbond_gpio_chip.parent = dev;
> +
> +	return devm_gpiochip_add_data(dev, &winbond_gpio_chip,
> &baseparam);
> +}
> +
> +static struct isa_driver winbond_gpio_idriver = {
> +	.driver = {
> +		.name	= WB_GPIO_DRIVER_NAME,
> +	},
> +	.match	= winbond_gpio_imatch,
> +	.probe	= winbond_gpio_iprobe,
> +};
> +
> +module_isa_driver(winbond_gpio_idriver, 1);
> +
> +module_param_named(base, baseparam, ulong, 0444);
> +MODULE_PARM_DESC(base,
> +		 "I/O port base (when unset - probe chip default
> ones)");
> +
> +/* This parameter sets which GPIO devices (ports) we enable */
> +module_param(gpios, ulong, 0444);
> +MODULE_PARM_DESC(gpios,
> +		 "bitmask of GPIO ports to enable (bit 0 - GPIO1, bit
> 1 - GPIO2, etc.");
> +
> +/*
> + * These two parameters below set how we configure GPIO ports output
> drivers.
> + * It can't be a one bitmask since we need three values per port:
> push-pull,
> + * open-drain and keep as-is (this is the default).
> + */
> +module_param(ppgpios, ulong, 0444);
> +MODULE_PARM_DESC(ppgpios,
> +		 "bitmask of GPIO ports to set to push-pull mode (bit
> 0 - GPIO1, bit 1 - GPIO2, etc.");
> +
> +module_param(odgpios, ulong, 0444);
> +MODULE_PARM_DESC(odgpios,
> +		 "bitmask of GPIO ports to set to open drain mode
> (bit 0 - GPIO1, bit 1 - GPIO2, etc.");
> +
> +/*
> + * GPIO2.0 and GPIO2.1 control a basic PC functionality that we
> + * don't allow tinkering with by default (it is very likely that the
> + * firmware owns these pins).
> + * These two parameters below allow overriding these prohibitions.
> + */
> +module_param(pledgpio, bool, 0644);
> +MODULE_PARM_DESC(pledgpio,
> +		 "enable changing value of GPIO2.0 bit (Power LED),
> default no.");
> +
> +module_param(beepgpio, bool, 0644);
> +MODULE_PARM_DESC(beepgpio,
> +		 "enable changing value of GPIO2.1 bit (BEEP),
> default no.");
> +
> +MODULE_AUTHOR("Maciej S. Szmigiero <mail@xxxxxxxxxxxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("GPIO interface for Winbond Super I/O chips");
> +MODULE_LICENSE("GPL");

-- 
Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
Intel Finland Oy
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html