On Mon, Jan 9, 2017 at 12:32 AM, Sudip Mukherjee
<sudipm.mukherjee@xxxxxxxxx> wrote:
> From: Sudip Mukherjee <sudip.mukherjee@xxxxxxxxxxxxxxx>
>
> Add the serial driver for the Exar chips. And also register the
> platform device for the gpio provided by the Exar chips.
GPIO ?
> Andy,
> I hope its ok this time. All your comments taken into account. :)
> I could not think of any other way to reduce the number of boards.
Almost but not entirely. Hope v9 will be in a really good shape.
Please wait also for my comment regarding patch 1 (basically style
ones since it will be v9)/
> +#undef DEBUG
> +
> +#include <asm/byteorder.h>
What I meant previously is a grouping like following
<linux/*>
<asm/*>
"*"
Each group is sorted, except special cases like 8250_pci.h here.
> +#define PCI_DEVICE_ID_COMMTECH_4224PCIE 0x0020
> +#define PCI_DEVICE_ID_COMMTECH_4228PCIE 0x0021
> +#define PCI_DEVICE_ID_COMMTECH_4222PCIE 0x0022
> +#define PCI_DEVICE_ID_EXAR_XR17V4358 0x4358
> +#define PCI_DEVICE_ID_EXAR_XR17V8358 0x8358
> +#define PCI_NUM_BAR_RESOURCES 6
Hmm... Do you use it somewhere? If no, remove, otherwise remove and
replace by generic definition.
> +
> +struct exar8250;
> +
> +struct exar8250_board {
> + unsigned int num_ports;
> + unsigned int base_baud;
> + unsigned int uart_offset; /* the space between channels */
> + /*
> + * reg_shift: describes how the UART registers are mapped
> + * to PCI memory by the card.
> + */
Those comments are good candidates to be a kernel doc description
above the struct definition.
> + unsigned int reg_shift;
> + unsigned int first_offset;
> + bool has_slave;
> + int (*setup)(struct exar8250 *, struct pci_dev *,
> + const struct exar8250_board *,
> + struct uart_8250_port *, int);
> + void (*exit)(struct pci_dev *dev);
> +};
> +
> +struct exar8250 {
> + unsigned int nr;
> + struct exar8250_board *board;
> + int line[0];
> +};
> +
> +static int default_setup(struct exar8250 *priv, struct pci_dev *pcidev,
I would use pci_dev, but it is matter of taste.
> + const struct exar8250_board *board,
> + struct uart_8250_port *port, int idx)
> +{
> + unsigned int offset = board->first_offset, bar = 0;
> +
> + offset += idx * board->uart_offset;
> +
> + port->port.iotype = UPIO_MEM;
> + port->port.iobase = 0;
> + port->port.mapbase = pci_resource_start(pcidev, bar) + offset;
> + port->port.membase = pcim_iomap_table(pcidev)[bar] + offset;
> + port->port.regshift = board->reg_shift;
> +
> + return 0;
> +}
> +
> +static int
> +pci_xr17c154_setup(struct exar8250 *priv, struct pci_dev *pcidev,
> + const struct exar8250_board *board,
> + struct uart_8250_port *port, int idx)
> +{
> + port->port.flags |= UPF_EXAR_EFR;
> + return default_setup(priv, pcidev, board, port, idx);
> +}
> +
> +static void setup_gpio(u8 __iomem *p)
> +{
> + writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
> + writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
> + writeb(0x00, p + UART_EXAR_MPIO3T_7_0);
> + writeb(0x00, p + UART_EXAR_MPIOINV_7_0);
> + writeb(0x00, p + UART_EXAR_MPIOSEL_7_0);
> + writeb(0x00, p + UART_EXAR_MPIOOD_7_0);
> + writeb(0x00, p + UART_EXAR_MPIOINT_15_8);
> + writeb(0x00, p + UART_EXAR_MPIOLVL_15_8);
> + writeb(0x00, p + UART_EXAR_MPIO3T_15_8);
> + writeb(0x00, p + UART_EXAR_MPIOINV_15_8);
> + writeb(0x00, p + UART_EXAR_MPIOSEL_15_8);
> + writeb(0x00, p + UART_EXAR_MPIOOD_15_8);
> +}
> +
> +static void *
> +xr17v35x_register_gpio(struct pci_dev *pcidev)
> +{
> + struct platform_device *pdev;
> +
> + pdev = platform_device_alloc("gpio_exar", PLATFORM_DEVID_AUTO);
> + if (!pdev)
> + return NULL;
> +
> + platform_set_drvdata(pdev, pcidev);
> + if (platform_device_add(pdev) < 0) {
> + platform_device_put(pdev);
> + return NULL;
> + }
> +
> + return (void *)pdev;
No need to explicit cast.
> +}
> +
> +static int
> +pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev,
> + const struct exar8250_board *board,
> + struct uart_8250_port *port, int idx)
> +{
> + u8 __iomem *p;
> + int ret;
> +
> + p = pci_ioremap_bar(pcidev, 0);
> + if (!p)
> + return -ENOMEM;
> +
> + port->port.flags |= UPF_EXAR_EFR;
> +
> + /*
> + * Setup the uart clock for the devices on expansion slot to
> + * half the clock speed of the main chip (which is 125MHz)
> + */
> + if (board->has_slave && idx >= 8)
> + port->port.uartclk = (7812500 * 16 / 2);
> +
> + /*
> + * Setup Multipurpose Input/Output pins.
> + */
> + if (idx == 0)
> + setup_gpio(p);
So, my question is can we do this in GPIO driver?
Can we register it beforehand if needed?
> +
> + writeb(0x00, p + UART_EXAR_8XMODE);
> + writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR);
> + writeb(128, p + UART_EXAR_TXTRG);
> + writeb(128, p + UART_EXAR_RXTRG);
> + iounmap(p);
> +
> + ret = default_setup(priv, pcidev, board, port, idx);
> + if (ret)
> + return ret;
> +
> + if (idx == 0)
> + port->port.private_data =
> + xr17v35x_register_gpio(pcidev);
> +
> + return 0;
> +}
> +
> +static void pci_xr17v35x_exit(struct pci_dev *dev)
Be consistent pci_dev or pcidev. Check all your patches all occurrences.
> +{
> + struct exar8250 *priv = pci_get_drvdata(dev);
> + struct uart_8250_port *port = serial8250_get_port(priv->line[0]);
> + struct platform_device *pdev = port->port.private_data;
> +
> + if (pdev) {
> + platform_device_unregister(pdev);
> + port->port.private_data = NULL;
> + }
Would
if (!pdev)
return;
be more suitable here?
> +}
> +
> +static int
> +exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent)
> +{
> + int rc;
Make it last in the definition block. I think I mentioned this earlier.
> + struct exar8250_board *board;
> + struct uart_8250_port uart;
> + struct exar8250 *priv;
> + unsigned int nr_ports, i, bar = 0, maxnr;
> +
> + board = (struct exar8250_board *)ent->driver_data;
> +
> + rc = pcim_enable_device(pcidev);
> + if (rc)
> + return rc;
> +
> + if (!pcim_iomap(pcidev, bar, 0) && !pcim_iomap_table(pcidev))
> + return -ENOMEM;
You ignored my comment, we may never finish the review in such case :-(
Asking again: do you really need this part? I know why I did so and
put it to 8250_pci, but let's focus on your code.
> +
> + maxnr = (pci_resource_len(pcidev, bar) - board->first_offset) >>
> + (board->reg_shift + 3);
> +
> + nr_ports = board->num_ports;
> +
> + priv = devm_kzalloc(&pcidev->dev, sizeof(*priv) +
> + sizeof(unsigned int) * nr_ports,
> + GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + priv->board = board;
> +
> + memset(&uart, 0, sizeof(uart));
> + uart.port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
> + uart.port.uartclk = board->base_baud * 16;
> + uart.port.irq = pcidev->irq;
> + uart.port.dev = &pcidev->dev;
> +
> + for (i = 0; i < nr_ports && i < maxnr; i++) {
> + if (board->setup(priv, pcidev, board, &uart, i))
> + break;
Shouldn't you inform user that something went wrong? Or is it okay?
> +
> + dev_dbg(&pcidev->dev, "Setup PCI port: port %lx, irq %d, type %d\n",
> + uart.port.iobase, uart.port.irq, uart.port.iotype);
> +
> + priv->line[i] = serial8250_register_8250_port(&uart);
> + if (priv->line[i] < 0) {
> + dev_err(&pcidev->dev,
> + "Couldn't register serial port %lx, irq %d, type %d, error %d\n",
> + uart.port.iobase, uart.port.irq,
> + uart.port.iotype, priv->line[i]);
> + break;
> + }
> + }
> + priv->nr = i;
> + pci_set_drvdata(pcidev, priv);
> + return 0;
> +}
> +
> +static void exar_pci_remove(struct pci_dev *pcidev)
> +{
> + int i;
Move it after next line and perhaps make unsigned int i;
> + struct exar8250 *priv = pci_get_drvdata(pcidev);
> +
> + for (i = 0; i < priv->nr; i++)
> + serial8250_unregister_port(priv->line[i]);
> +
> + if (priv->board->exit)
> + priv->board->exit(pcidev);
> +}
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int exar_suspend(struct device *dev)
> +{
> + struct pci_dev *pdev = to_pci_dev(dev);
pci_dev or pcidev.
> + struct exar8250 *priv = pci_get_drvdata(pdev);
> + unsigned int i;
> +
> + for (i = 0; i < priv->nr; i++)
> + if (priv->line[i] >= 0)
> + serial8250_suspend_port(priv->line[i]);
> +
> + /*
> + * Ensure that every init quirk is properly torn down
> + */
One line?
> + if (priv->board->exit)
> + priv->board->exit(pdev);
> +
> + return 0;
> +}
> +
> +static int exar_resume(struct device *dev)
> +{
> + struct pci_dev *pdev = to_pci_dev(dev);
> + struct exar8250 *priv = pci_get_drvdata(pdev);
> + unsigned int i;
> +
> + if (priv) {
Would be the case that priv == NULL here?
> + for (i = 0; i < priv->nr; i++)
> + if (priv->line[i] >= 0)
> + serial8250_resume_port(priv->line[i]);
> + }
> +
> + return 0;
> +}
> +#endif
> +
> +static SIMPLE_DEV_PM_OPS(exar_pci_pm, exar_suspend, exar_resume);
> +
Now see how we can reduce more.
> +static const struct exar8250_board pbn_b0_2_1843200_200 = {
> + .num_ports = 2,
> + .base_baud = 1843200,
> + .uart_offset = 0x200,
> + .setup = pci_xr17c154_setup
> +};
> +
> +static const struct exar8250_board pbn_b0_4_1843200_200 = {
> + .num_ports = 4,
> + .base_baud = 1843200,
> + .uart_offset = 0x200,
> + .setup = pci_xr17c154_setup
> +};
> +
> +static const struct exar8250_board pbn_b0_8_1843200_200 = {
> + .num_ports = 8,
> + .base_baud = 1843200,
> + .uart_offset = 0x200,
> + .setup = pci_xr17c154_setup,
> +};
> +
> +static const struct exar8250_board pbn_exar_ibm_saturn = {
> + .num_ports = 1,
> + .base_baud = 921600,
> + .uart_offset = 0x200,
> + .setup = pci_xr17c154_setup,
> +};
> +
> +static const struct exar8250_board pbn_exar_XR17C152 = {
> + .num_ports = 2,
> + .base_baud = 921600,
> + .uart_offset = 0x200,
> + .setup = pci_xr17c154_setup,
> +};
> +
> +static const struct exar8250_board pbn_exar_XR17C154 = {
> + .num_ports = 4,
> + .base_baud = 921600,
> + .uart_offset = 0x200,
> + .setup = pci_xr17c154_setup,
> +};
> +
> +static const struct exar8250_board pbn_exar_XR17C158 = {
> + .num_ports = 8,
> + .base_baud = 921600,
> + .uart_offset = 0x200,
> + .setup = pci_xr17c154_setup,
> +};
> +
Port number is easily to get from device ID, I already said this.
nr = subvendor == PCI_VENDOR_ID_IBM ? 1 : device & 0x0f;
Yes, it means ->setup() hook will allocate memory for lines (declare
them as int *line and use devm_kcalloc).
And if you think smarter about returning value, you may not even need
to move registration code into it!
Moreover all above have same setup function and uart_offset. Use it.
> +static const struct exar8250_board pbn_exar_XR17V352 = {
> + .num_ports = 2,
> + .base_baud = 7812500,
> + .uart_offset = 0x400,
> + .setup = pci_xr17v35x_setup,
> + .exit = pci_xr17v35x_exit,
> +};
> +
> +static const struct exar8250_board pbn_exar_XR17V354 = {
> + .num_ports = 4,
> + .base_baud = 7812500,
> + .uart_offset = 0x400,
> + .setup = pci_xr17v35x_setup,
> + .exit = pci_xr17v35x_exit,
> +};
> +
> +static const struct exar8250_board pbn_exar_XR17V358 = {
> + .num_ports = 8,
> + .base_baud = 7812500,
> + .uart_offset = 0x400,
> + .setup = pci_xr17v35x_setup,
> + .exit = pci_xr17v35x_exit,
> +};
> +
> +static const struct exar8250_board pbn_exar_XR17V4358 = {
> + .num_ports = 12,
> + .base_baud = 7812500,
> + .uart_offset = 0x400,
> + .has_slave = true,
> + .setup = pci_xr17v35x_setup,
> + .exit = pci_xr17v35x_exit,
> +};
> +
> +static const struct exar8250_board pbn_exar_XR17V8358 = {
> + .num_ports = 16,
> + .base_baud = 7812500,
> + .uart_offset = 0x400,
> + .has_slave = true,
> + .setup = pci_xr17v35x_setup,
> + .exit = pci_xr17v35x_exit,
Offset + baud rate are same.
So, offset is not needed in the struct at all.
Does it make sense to you?
> +};
Below looks much better!
> +#define CONNECT_DEVICE(devid, sdevid, board) { PCI_DEVICE_SUB(\
Please do use separate line for PCI_DEVICE_SUB
> + PCI_VENDOR_ID_EXAR,\
> + PCI_DEVICE_ID_EXAR_##devid,\
> + PCI_SUBVENDOR_ID_CONNECT_TECH,\
> + PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_##sdevid),\
> + 0, 0, (kernel_ulong_t)&board }
...also for }
And shift this line to show that is related to top level
> +
> +#define EXAR_DEVICE(vend, devid, bd) { PCI_VDEVICE(vend,\
> + PCI_DEVICE_ID_##devid), (kernel_ulong_t)&bd }
Same comments.
> +
> +static struct pci_device_id exar_pci_tbl[] = {
> + CONNECT_DEVICE(XR17C152, UART_2_232, pbn_b0_2_1843200_200),
> + CONNECT_DEVICE(XR17C154, UART_4_232, pbn_b0_4_1843200_200),
> + CONNECT_DEVICE(XR17C158, UART_8_232, pbn_b0_8_1843200_200),
> + CONNECT_DEVICE(XR17C152, UART_1_1, pbn_b0_2_1843200_200),
> + CONNECT_DEVICE(XR17C154, UART_2_2, pbn_b0_4_1843200_200),
> + CONNECT_DEVICE(XR17C158, UART_4_4, pbn_b0_8_1843200_200),
> + CONNECT_DEVICE(XR17C152, UART_2, pbn_b0_2_1843200_200),
> + CONNECT_DEVICE(XR17C154, UART_4, pbn_b0_4_1843200_200),
> + CONNECT_DEVICE(XR17C158, UART_8, pbn_b0_8_1843200_200),
> + CONNECT_DEVICE(XR17C152, UART_2_485, pbn_b0_2_1843200_200),
> + CONNECT_DEVICE(XR17C154, UART_4_485, pbn_b0_4_1843200_200),
> + CONNECT_DEVICE(XR17C158, UART_8_485, pbn_b0_8_1843200_200),
> + { PCI_DEVICE_SUB(PCI_VENDOR_ID_EXAR,
> + PCI_DEVICE_ID_EXAR_XR17C152,
> + PCI_VENDOR_ID_IBM,
> + PCI_SUBDEVICE_ID_IBM_SATURN_SERIAL_ONE_PORT), 0, 0,
> + (kernel_ulong_t)&pbn_exar_ibm_saturn },
Ditto.
> + /*
> + * Exar Corp. XR17C15[248] Dual/Quad/Octal UART
> + */
One line?
> + EXAR_DEVICE(EXAR, EXAR_XR17C152, pbn_exar_XR17C152),
> + EXAR_DEVICE(EXAR, EXAR_XR17C154, pbn_exar_XR17C154),
> + EXAR_DEVICE(EXAR, EXAR_XR17C158, pbn_exar_XR17C158),
> + /*
> + * Exar Corp. XR17V[48]35[248] Dual/Quad/Octal/Hexa PCIe UARTs
> + */
Ditto.
> + EXAR_DEVICE(EXAR, EXAR_XR17V352, pbn_exar_XR17V352),
> + EXAR_DEVICE(EXAR, EXAR_XR17V354, pbn_exar_XR17V354),
> + EXAR_DEVICE(EXAR, EXAR_XR17V358, pbn_exar_XR17V358),
> + EXAR_DEVICE(EXAR, EXAR_XR17V4358, pbn_exar_XR17V4358),
> + EXAR_DEVICE(EXAR, EXAR_XR17V8358, pbn_exar_XR17V8358),
> + EXAR_DEVICE(COMMTECH, COMMTECH_4222PCIE, pbn_exar_XR17V352),
> + EXAR_DEVICE(COMMTECH, COMMTECH_4224PCIE, pbn_exar_XR17V354),
> + EXAR_DEVICE(COMMTECH, COMMTECH_4228PCIE, pbn_exar_XR17V358),
> + { 0, }
> +};
> +MODULE_DEVICE_TABLE(pci, exar_pci_tbl);
Move this to the next line after actual structure.
> --- a/drivers/tty/serial/8250/Kconfig
> +++ b/drivers/tty/serial/8250/Kconfig
> +config SERIAL_8250_EXAR
> + tristate "8250/16550 PCI device support"
> + depends on SERIAL_8250_PCI
> + default SERIAL_8250
Looks like this line has indentation issue. Moreover I told you to do
this in patch 3, not here. Otherwise you will have drivers overlap.
--
With Best Regards,
Andy Shevchenko
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH v8 2/3] serial: exar: split out the exar code from 8250_pci
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: Re: [PATCH v8 2/3] serial: exar: split out the exar code from 8250_pci
- From: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
- Date: Mon, 9 Jan 2017 02:14:29 +0200
- In-reply-to: <1483914727-6076-2-git-send-email-sudipm.mukherjee@gmail.com>
- References: <1483914727-6076-1-git-send-email-sudipm.mukherjee@gmail.com> <1483914727-6076-2-git-send-email-sudipm.mukherjee@gmail.com>
- Follow-Ups:
- Re: [PATCH v8 2/3] serial: exar: split out the exar code from 8250_pci
- From: Sudip Mukherjee
- Re: [PATCH v8 2/3] serial: exar: split out the exar code from 8250_pci
- From: Andy Shevchenko
- Re: [PATCH v8 2/3] serial: exar: split out the exar code from 8250_pci
- References:
- [PATCH v8 1/3] gpio: exar: add gpio for exar cards
- From: Sudip Mukherjee
- [PATCH v8 2/3] serial: exar: split out the exar code from 8250_pci
- From: Sudip Mukherjee
- [PATCH v8 1/3] gpio: exar: add gpio for exar cards
- Prev by Date: [PATCH v8 2/3] serial: exar: split out the exar code from 8250_pci
- Next by Date: Re: [linux-sunxi] [PATCH 1/2] drivers: pinctrl: add driver for Allwinner H5 SoC
- Previous by thread: [PATCH v8 2/3] serial: exar: split out the exar code from 8250_pci
- Next by thread: Re: [PATCH v8 2/3] serial: exar: split out the exar code from 8250_pci
- Index(es):
 |