[PATCH] gpio: menz127: use the new open drain callback

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The menz127 driver tries to support open drain by detecting it
at request time. However: without the new callbacks from the
gpiolib it is not really working: the core will still just emulate
the open drain mode by switching the line to an input.

By adding a hook into the new .set_single_ended() call rather than
trying to autodetect at request() time, proper open drain can be
supported.

Cc: Andreas Werner <andy@xxxxxxxxxxxxx>
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
 drivers/gpio/gpio-menz127.c | 18 +++++++++++-------
 1 file changed, 11 insertions(+), 7 deletions(-)

diff --git a/drivers/gpio/gpio-menz127.c b/drivers/gpio/gpio-menz127.c
index 8c1ab8e1974f..334fe270dcf1 100644
--- a/drivers/gpio/gpio-menz127.c
+++ b/drivers/gpio/gpio-menz127.c
@@ -88,21 +88,25 @@ static int men_z127_debounce(struct gpio_chip *gc, unsigned gpio,
 	return 0;
 }
 
-static int men_z127_request(struct gpio_chip *gc, unsigned gpio_pin)
+static int men_z127_set_single_ended(struct gpio_chip *gc,
+				     unsigned offset,
+				     enum single_ended_mode mode)
 {
 	struct men_z127_gpio *priv = gpiochip_get_data(gc);
 	u32 od_en;
 
-	if (gpio_pin >= gc->ngpio)
-		return -EINVAL;
+	if (mode != LINE_MODE_OPEN_DRAIN &&
+	    mode != LINE_MODE_PUSH_PULL)
+		return -ENOTSUPP;
 
 	spin_lock(&priv->lock);
 	od_en = readl(priv->reg_base + MEN_Z127_ODER);
 
-	if (gpiochip_line_is_open_drain(gc, gpio_pin))
-		od_en |= BIT(gpio_pin);
+	if (mode == LINE_MODE_OPEN_DRAIN)
+		od_en |= BIT(offset);
 	else
-		od_en &= ~BIT(gpio_pin);
+		/* Implicitly LINE_MODE_PUSH_PULL */
+		od_en &= ~BIT(offset);
 
 	writel(od_en, priv->reg_base + MEN_Z127_ODER);
 	spin_unlock(&priv->lock);
@@ -147,7 +151,7 @@ static int men_z127_probe(struct mcb_device *mdev,
 		goto err_unmap;
 
 	men_z127_gpio->gc.set_debounce = men_z127_debounce;
-	men_z127_gpio->gc.request = men_z127_request;
+	men_z127_gpio->gc.set_single_ended = men_z127_set_single_ended;
 
 	ret = gpiochip_add_data(&men_z127_gpio->gc, men_z127_gpio);
 	if (ret) {
-- 
2.4.3

--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux