Hello, Richard and Jeff,
we found that llseek has another bug when in SEEK_END. it should be
add the inode lock and unlock.
this bug can be reproduce the following scenario:
on one nodeA, open the file and then write some data to file and
close the file .
on another nodeB , open the file and llseek the end of file . the
position of file is old.
On 2013/6/15 13:09, Jeff Liu wrote:
[Add ocfs2-devel to CC-list]
Hello Richard,
Thanks for your patch.
On 06/15/2013 03:23 AM, Richard Yao wrote:
There are multiple issues with the custom llseek implemented in ocfs2 for
implementing SEEK_HOLE/SEEK_DATA.
1. It takes the inode->i_mutex lock before calling generic_file_llseek(), which
is unnecessary.
Agree, but please see my comments below.
2. It fails to take the filp->f_lock spinlock before modifying filp->f_pos and
filp->f_version, which differs from generic_file_llseek().
3. It does a offset> inode->i_sb->s_maxbytes check that permits seeking up to
the maximum file size possible on the ocfs2 filesystem, even when it is past
the end of the file. Seeking beyond that (if possible), would return EINVAL
instead of ENXIO.
4. The switch statement tries to cover all whence values when in reality it
should only care about SEEK_HOLE/SEEK_DATA. Any other cases should be passsed
to generic_file_llseek().
I have another patch set for refactoring ocfs2_file_llseek() but not yet found time
to run a comprehensive tests. It can solve the existing issues but also improved the
SEEK_DATA/SEEK_HOLE for unwritten extents, i.e. OCFS2_EXT_UNWRITTEN.
With this change, SEEK_DATA/SEEK_HOLE will go into separate function with a little code
duplication instead of the current mix-ups in ocfs2_seek_data_hole_offset(), i.e,
loff_t ocfs2_file_llseek()
{
switch (origin) {
case SEEK_END:
case SEEK_CUR:
case SEEK_SET:
return generic_file_llseek(file, offset, origin);
case SEEK_DATA:
return ocfs2_seek_data(file, offset);
case SEEK_HOLE:
return ocfs2_seek_hole(file, offset);
default:
return -EINVAL;
}
}
I personally like keeping SEEK_DATA/SEEK_HOLE in switch...case style rather
than dealing with them in a condition check block.
Thanks,
-Jeff
btrfs_file_llseek() and ocfs2_file_llseek() are extremely similar and
consequently, contain many of the same flaws. Li Dongyang filed a pull
request with ZFSOnLinux for SEEK_HOLE/SEEK_DATA support that included a
custom llseek function that appears to have been modelled after the one
in ocfs2. The similarity was strong enough that it suffered from many of
the same flaws, which I caught during review. I addressed the issues
with his patch with one that I wrote. Since a small percentage of Gentoo
Linux users are affected by these flaws, I decided to adapt that code
that to btrfs (separate patch) and ocfs2.
Note that commit 48802c8ae2a9d618ec734a61283d645ad527e06c by Jeff Liu at
Oracle mostly addressed #3 in btrfs. The only lingering issue was that
the offset> inode->i_sb->s_maxbytes check became dead code. The ocfs2
code was not fortunate enough to have had a similar correction until
now.
Signed-off-by: Richard Yao<ryao@xxxxxxxxxx>
---
fs/ocfs2/file.c | 65 ++++++++++++++++++++++-----------------------------------
1 file changed, 25 insertions(+), 40 deletions(-)
diff --git a/fs/ocfs2/file.c b/fs/ocfs2/file.c
index ff54014..84f8c9c 100644
--- a/fs/ocfs2/file.c
+++ b/fs/ocfs2/file.c
@@ -2615,54 +2615,39 @@ bail:
}
/* Refer generic_file_llseek_unlocked() */
-static loff_t ocfs2_file_llseek(struct file *file, loff_t offset, int whence)
+static loff_t ocfs2_file_llseek(struct file *filp, loff_t offset, int whence)
{
- struct inode *inode = file->f_mapping->host;
- int ret = 0;
+ if (whence == SEEK_DATA || whence == SEEK_HOLE) {
+ struct inode *inode = filp->f_mapping->host;
+ int ret;
- mutex_lock(&inode->i_mutex);
+ if (offset< 0&& !(filp->f_mode& FMODE_UNSIGNED_OFFSET))
+ return -EINVAL;
- switch (whence) {
- case SEEK_SET:
- break;
- case SEEK_END:
- offset += inode->i_size;
- break;
- case SEEK_CUR:
- if (offset == 0) {
- offset = file->f_pos;
- goto out;
+ if (offset>= i_size_read(inode)) {
+ return -ENXIO;
}
- offset += file->f_pos;
- break;
- case SEEK_DATA:
- case SEEK_HOLE:
- ret = ocfs2_seek_data_hole_offset(file,&offset, whence);
- if (ret)
- goto out;
- break;
- default:
- ret = -EINVAL;
- goto out;
- }
- if (offset< 0&& !(file->f_mode& FMODE_UNSIGNED_OFFSET))
- ret = -EINVAL;
- if (!ret&& offset> inode->i_sb->s_maxbytes)
- ret = -EINVAL;
- if (ret)
- goto out;
+ mutex_lock(&inode->i_mutex);
+ ret = ocfs2_seek_data_hole_offset(filp,&offset, whence);
+ mutex_unlock(&inode->i_mutex);
+
+ if (ret) {
+ return ret;
+ }
- if (offset != file->f_pos) {
- file->f_pos = offset;
- file->f_version = 0;
+ if (offset != filp->f_pos) {
+ spin_lock(&filp->f_lock);
+ filp->f_pos = offset;
+ filp->f_version = 0;
+ spin_unlock(&filp->f_lock);
+ }
+
+ return offset;
}
-out:
- mutex_unlock(&inode->i_mutex);
- if (ret)
- return ret;
- return offset;
+ return generic_file_llseek(filp, offset, whence);
+
}
const struct inode_operations ocfs2_file_iops = {
_______________________________________________
Ocfs2-devel mailing list
Ocfs2-devel@xxxxxxxxxxxxxx
https://oss.oracle.com/mailman/listinfo/ocfs2-devel
.
--
To unsubscribe from this list: send the line "unsubscribe linux-fsdevel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
