On Wed, Jan 31, 2024 at 06:05:33PM -0500, Charles Perry wrote:
> Xilinx 7 series FPGA can be programmed using a slave parallel port named
> the SelectMAP interface in the datasheet. This slave interface is
> compatible with the i.MX6 EIM bus controller but other types of external
> memory mapped parallel bus might work.
>
> xilinx-selectmap currently only supports the x8 mode where data is loaded
> at one byte per rising edge of the clock, with the MSb of each byte
> presented to the D0 pin.
>
> Signed-off-by: Charles Perry <charles.perry@xxxxxxxxxxxxxxxxxxxx>
> ---
> drivers/fpga/Kconfig | 8 +++
> drivers/fpga/Makefile | 1 +
> drivers/fpga/xilinx-core.c | 11 +++-
> drivers/fpga/xilinx-core.h | 3 +-
> drivers/fpga/xilinx-selectmap.c | 106 ++++++++++++++++++++++++++++++++
> drivers/fpga/xilinx-spi.c | 3 +-
> 6 files changed, 127 insertions(+), 5 deletions(-)
> create mode 100644 drivers/fpga/xilinx-selectmap.c
>
> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> index d27a1ebf40838..37b35f58f0dfb 100644
> --- a/drivers/fpga/Kconfig
> +++ b/drivers/fpga/Kconfig
> @@ -67,6 +67,14 @@ config FPGA_MGR_STRATIX10_SOC
> config FPGA_MGR_XILINX_CORE
> tristate
>
> +config FPGA_MGR_XILINX_SELECTMAP
> + tristate "Xilinx Configuration over SelectMAP"
> + depends on HAS_IOMEM
> + select FPGA_MGR_XILINX_CORE
> + help
> + FPGA manager driver support for Xilinx FPGA configuration
> + over SelectMAP interface.
> +
> config FPGA_MGR_XILINX_SPI
> tristate "Xilinx Configuration over Slave Serial (SPI)"
> depends on SPI
> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> index 7ec795b6a5a70..aeb89bb13517e 100644
> --- a/drivers/fpga/Makefile
> +++ b/drivers/fpga/Makefile
> @@ -16,6 +16,7 @@ obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10) += socfpga-a10.o
> obj-$(CONFIG_FPGA_MGR_STRATIX10_SOC) += stratix10-soc.o
> obj-$(CONFIG_FPGA_MGR_TS73XX) += ts73xx-fpga.o
> obj-$(CONFIG_FPGA_MGR_XILINX_CORE) += xilinx-core.o
> +obj-$(CONFIG_FPGA_MGR_XILINX_SELECTMAP) += xilinx-selectmap.o
> obj-$(CONFIG_FPGA_MGR_XILINX_SPI) += xilinx-spi.o
> obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA) += zynq-fpga.o
> obj-$(CONFIG_FPGA_MGR_ZYNQMP_FPGA) += zynqmp-fpga.o
> diff --git a/drivers/fpga/xilinx-core.c b/drivers/fpga/xilinx-core.c
> index aff40e9394085..64117759be100 100644
> --- a/drivers/fpga/xilinx-core.c
> +++ b/drivers/fpga/xilinx-core.c
> @@ -180,21 +180,26 @@ static const struct fpga_manager_ops xilinx_core_ops = {
>
> int xilinx_core_probe(struct xilinx_fpga_core *core, struct device *dev,
> xilinx_write_func write,
> - xilinx_write_one_dummy_byte_func write_one_dummy_byte)
> + xilinx_write_one_dummy_byte_func write_one_dummy_byte,
> + const char *prog_con_id, const char *init_con_id)
These gpio name inputs are not necessary except for DTS format concern.
Is it possible we don't change the names?
> {
> struct fpga_manager *mgr;
>
> + if (!core || !dev || !write || !write_one_dummy_byte || !prog_con_id ||
> + !init_con_id)
> + return -EINVAL;
These checks belong to Patch #1.
> +
> core->dev = dev;
> core->write = write;
> core->write_one_dummy_byte = write_one_dummy_byte;
>
> /* PROGRAM_B is active low */
> - core->prog_b = devm_gpiod_get(dev, "prog_b", GPIOD_OUT_LOW);
> + core->prog_b = devm_gpiod_get(dev, prog_con_id, GPIOD_OUT_LOW);
> if (IS_ERR(core->prog_b))
> return dev_err_probe(dev, PTR_ERR(core->prog_b),
> "Failed to get PROGRAM_B gpio\n");
>
> - core->init_b = devm_gpiod_get_optional(dev, "init-b", GPIOD_IN);
> + core->init_b = devm_gpiod_get_optional(dev, init_con_id, GPIOD_IN);
> if (IS_ERR(core->init_b))
> return dev_err_probe(dev, PTR_ERR(core->init_b),
> "Failed to get INIT_B gpio\n");
> diff --git a/drivers/fpga/xilinx-core.h b/drivers/fpga/xilinx-core.h
> index 40e120945ba70..817f0e551d093 100644
> --- a/drivers/fpga/xilinx-core.h
> +++ b/drivers/fpga/xilinx-core.h
> @@ -22,6 +22,7 @@ struct xilinx_fpga_core {
>
> int xilinx_core_probe(struct xilinx_fpga_core *core, struct device *dev,
> xilinx_write_func write,
> - xilinx_write_one_dummy_byte_func write_one_dummy_byte);
> + xilinx_write_one_dummy_byte_func write_one_dummy_byte,
> + const char *prog_con_id, const char *init_con_id);
>
> #endif /* __XILINX_CORE_H */
> diff --git a/drivers/fpga/xilinx-selectmap.c b/drivers/fpga/xilinx-selectmap.c
> new file mode 100644
> index 0000000000000..08054e19bb498
> --- /dev/null
> +++ b/drivers/fpga/xilinx-selectmap.c
> @@ -0,0 +1,106 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Xilinx Spartan6 and 7 Series SelectMAP interface driver
> + *
> + * (C) 2024 Charles Perry <charles.perry@xxxxxxxxxxxxxxxxxxxx>
> + *
> + * Manage Xilinx FPGA firmware loaded over the SelectMAP configuration
> + * interface.
> + */
> +
> +#include "xilinx-core.h"
> +
> +#include <linux/platform_device.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/module.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/of.h>
> +#include <linux/io.h>
> +
> +struct xilinx_selectmap_conf {
> + struct xilinx_fpga_core core;
> + void __iomem *base;
> + struct gpio_desc *csi_b;
> + struct gpio_desc *rdwr_b;
These 2 gpio_desc are not used globally, maybe remove them here.
> +};
> +
> +#define to_xilinx_selectmap_conf(obj) \
> + container_of(obj, struct xilinx_selectmap_conf, core)
> +
> +static int xilinx_selectmap_write(struct xilinx_fpga_core *core,
> + const char *buf, size_t count)
> +{
> + struct xilinx_selectmap_conf *conf = to_xilinx_selectmap_conf(core);
> + u32 i;
> +
> + for (i = 0; i < count; ++i)
> + writeb(buf[i], conf->base);
> +
> + return 0;
> +}
> +
> +static int xilinx_selectmap_apply_padding(struct xilinx_fpga_core *core)
> +{
> + struct xilinx_selectmap_conf *conf = to_xilinx_selectmap_conf(core);
> +
> + writeb(0xFF, conf->base);
Seems only one callback needed. Just use write() to xfer 1 byte?
Thanks,
Yilun
> + return 0;
> +}
> +
> +static int xilinx_selectmap_probe(struct platform_device *pdev)
> +{
> + struct xilinx_selectmap_conf *conf;
> + struct resource *r;
> + void __iomem *base;
> +
> + conf = devm_kzalloc(&pdev->dev, sizeof(*conf), GFP_KERNEL);
> + if (!conf)
> + return -ENOMEM;
> +
> + base = devm_platform_get_and_ioremap_resource(pdev, 0, &r);
> + if (IS_ERR(base))
> + return dev_err_probe(&pdev->dev, PTR_ERR(base),
> + "ioremap error\n");
> + conf->base = base;
> +
> + /* CSI_B is active low */
> + conf->csi_b =
> + devm_gpiod_get_optional(&pdev->dev, "csi", GPIOD_OUT_HIGH);
> + if (IS_ERR(conf->csi_b))
> + return dev_err_probe(&pdev->dev, PTR_ERR(conf->csi_b),
> + "Failed to get CSI_B gpio\n");
> +
> + /* RDWR_B is active low */
> + conf->rdwr_b =
> + devm_gpiod_get_optional(&pdev->dev, "rdwr", GPIOD_OUT_HIGH);
> + if (IS_ERR(conf->rdwr_b))
> + return dev_err_probe(&pdev->dev, PTR_ERR(conf->rdwr_b),
> + "Failed to get RDWR_B gpio\n");
> +
> + return xilinx_core_probe(&conf->core, &pdev->dev,
> + xilinx_selectmap_write,
> + xilinx_selectmap_apply_padding, "prog",
> + "init");
> +}
> +
> +static const struct of_device_id xlnx_selectmap_of_match[] = {
> + {
> + .compatible = "xlnx,fpga-selectmap",
> + },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, xlnx_selectmap_of_match);
> +
> +static struct platform_driver xilinx_selectmap_driver = {
> + .driver = {
> + .name = "xilinx-selectmap",
> + .of_match_table = xlnx_selectmap_of_match,
> + },
> + .probe = xilinx_selectmap_probe,
> +};
> +
> +module_platform_driver(xilinx_selectmap_driver);
> +
> +MODULE_LICENSE("GPL");
> +MODULE_AUTHOR("Charles Perry <charles.perry@xxxxxxxxxxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("Load Xilinx FPGA firmware over SelectMap");
> diff --git a/drivers/fpga/xilinx-spi.c b/drivers/fpga/xilinx-spi.c
> index ec128dee97312..b9ab3d5da004c 100644
> --- a/drivers/fpga/xilinx-spi.c
> +++ b/drivers/fpga/xilinx-spi.c
> @@ -74,7 +74,8 @@ static int xilinx_spi_probe(struct spi_device *spi)
> conf->spi = spi;
>
> return xilinx_core_probe(&conf->core, &spi->dev, xilinx_spi_write,
> - xilinx_spi_apply_cclk_cycles);
> + xilinx_spi_apply_cclk_cycles, "prog_b",
> + "init-b");
> }
>
> #ifdef CONFIG_OF
> --
> 2.43.0
>
>
