----- On Feb 2, 2024, at 5:49 AM, Krzysztof Kozlowski krzysztof.kozlowski@xxxxxxxxxx wrote: > On 01/02/2024 19:24, Charles Perry wrote: >> >> >> ----- On Feb 1, 2024, at 3:07 AM, Krzysztof Kozlowski >> krzysztof.kozlowski@xxxxxxxxxx wrote: >> >>> On 01/02/2024 00:05, Charles Perry wrote: >>>> Document the slave SelectMAP interface of Xilinx 7 series FPGA. >>>> >>>> Signed-off-by: Charles Perry <charles.perry@xxxxxxxxxxxxxxxxxxxx> >>>> --- >>>> .../bindings/fpga/xlnx,fpga-selectmap.yaml | 83 +++++++++++++++++++ >>>> 1 file changed, 83 insertions(+) >>>> create mode 100644 >>>> Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml >>>> >>>> diff --git a/Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml >>>> b/Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml >>>> new file mode 100644 >>>> index 0000000000000..c9a446b43cdd9 >>>> --- /dev/null >>>> +++ b/Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml >>>> @@ -0,0 +1,83 @@ >>>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) >>>> +%YAML 1.2 >>>> +--- >>>> +$id: http://devicetree.org/schemas/fpga/xlnx,fpga-selectmap.yaml# >>>> +$schema: http://devicetree.org/meta-schemas/core.yaml# >>>> + >>>> +title: Xilinx SelectMAP FPGA interface >>>> + >>>> +maintainers: >>>> + - Charles Perry <charles.perry@xxxxxxxxxxxxxxxxxxxx> >>>> + >>>> +description: | >>>> + Xilinx 7 Series FPGAs support a method of loading the bitstream over a >>>> + parallel port named the SelectMAP interface in the documentation. Only >>>> + the x8 mode is supported where data is loaded at one byte per rising edge of >>>> + the clock, with the MSB of each byte presented to the D0 pin. >>>> + >>>> + Datasheets: >>>> + >>>> https://www.xilinx.com/support/documentation/user_guides/ug470_7Series_Config.pdf >>>> + >>>> +allOf: >>>> + - $ref: /schemas/memory-controllers/mc-peripheral-props.yaml# >>>> + >>>> +properties: >>>> + compatible: >>>> + enum: >>>> + - xlnx,fpga-selectmap >>> >>> Your description mentions "7 Series" which is not present in compatible >>> and title. What is exactly the product here? Interface usually is not >>> the final binding, so is this specific to some particular FPGA or SoC? >>> >>> >>> Best regards, >>> Krzysztof >> >> This is specific to the FPGA, the 7 series encompass the following part >> family: >> * Spartan-7 (XC7S6, XC7S15, ... XC7S100) >> * Artix-7 (XC7A12T, XC7A15T, ... XC7A200T) >> * Kintex-7 (XC7K70T, XC7K160T, ... XC7K480T) >> * Virtex-7 (XC7V585T, XC7V2000T, >> XC7VX330T, XC7VX415T, ... XC7VX1140T, >> XC7VH580T, XC7VH870T) >> >> >> The configuration guide of Xilinx [1] tells us that all those devices >> share a common programming scheme. >> >> I do agree that having a mention of "7 series" in the compatible name >> would be beneficial as Xilinx has more FPGA than just the 7 series. >> The name was inspired from "xlnx,fpga-slave-serial" which is the compatible >> for the serial interface. >> >> What about "xlnx,fpga-xc7-selectmap" ? >> > > I am not sure what xc7 is and how Xilinx numbers it products, but > compatibles are supposed to be device specific, not family. Common > programming model could be denoted with generic fallback, but then the > fallback could be device-specific as well, which usually we recommend. > > Best regards, > Krzysztof XC7 is the common prefix for all 4 families of the 7 series. Then we have XC7S, XC7A, XC7K and XC7V as the prefixes of those 4 family. Following that is a number denoting the number of logic element, e.g. XC7S6, XC7S15, XC7S100, ... I don't think that should be part of the compatible. Finally there will be another set of letters and numbers for the temperature grade and physical package, but those are usually not part of a compatible string. I'll change it to four compatibles: "xlnx,fpga-xc7[sakv]-selectmap" so that the driver can do device specific things if anomalies are found in one of them. Thanks again for the review! Regards, Charles
