Steven Toth wrote: > Patrick Boisvenue wrote: >> I cannot get my new HVR-1500Q to work at all even though it's >> recognized as such. The best I was able to figure out was it does not >> like the eeprom. After enabling the debug mode on tveeprom, I got the >> following when loading cx23885: > > ... > >> cx23885[0]: warning: unknown hauppauge model #0 >> cx23885[0]: hauppauge eeprom: model=0 >> cx23885[0]: cx23885 based dvb card > > ... > >> Did a hg pull -u http://linuxtv.org/hg/v4l-dvb earlier today so >> running off recent codebase. > > Fixed it, see linuxtv.org/hg/~stoth/v4l-dvb. > > Pull the topmost patch and try again, please post your results back here. > > Thanks, > > Steve > Getting better, the eeprom parsing seems to work (check dmesg output below). However, doing a dvbscan still nets me no stations while doing a scan in a WindowsXP laptop gets me the expected two (2) stations in my area. dmesg output with tveeprom debug=1 and cx23885 debug=5 after loading cx23885 module: cx23885 driver version 0.0.1 loaded ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 19 cx23885[0]/0: cx23885_dev_setup() Memory configured for PCIe bridge type 885 cx23885[0]/0: cx23885_init_tsport(portno=2) CORE cx23885[0]: subsystem: 0070:7790, board: Hauppauge WinTV-HVR1500Q [card=5,autodetected] cx23885[0]/0: cx23885_pci_quirks() cx23885[0]/0: cx23885_dev_setup() tuner_type = 0x0 tuner_addr = 0x0 cx23885[0]/0: cx23885_dev_setup() radio_type = 0x0 radio_addr = 0x0 cx23885[0]/0: cx23885_reset() cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [VID A] cx23885[0]/0: cx23885_sram_channel_setup() 0x000104c0 <- 0x00000040 cx23885[0]/0: cx23885_sram_channel_setup() 0x000104d0 <- 0x00000b80 cx23885[0]/0: cx23885_sram_channel_setup() 0x000104e0 <- 0x000016c0 cx23885[0]/0: [bridge 885] sram setup VID A: bpl=2880 lines=3 cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch2] cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS1 B] cx23885[0]/0: cx23885_sram_channel_setup() 0x00010580 <- 0x00005000 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010590 <- 0x000052f0 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105a0 <- 0x000055e0 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105b0 <- 0x000058d0 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105c0 <- 0x00005bc0 cx23885[0]/0: [bridge 885] sram setup TS1 B: bpl=752 lines=5 cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch4] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch5] cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS2 C] cx23885[0]/0: cx23885_sram_channel_setup() 0x000105e0 <- 0x00006000 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105f0 <- 0x000062f0 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010600 <- 0x000065e0 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010610 <- 0x000068d0 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010620 <- 0x00006bc0 cx23885[0]/0: [bridge 885] sram setup TS2 C: bpl=752 lines=5 cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch7] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch8] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch9] cx23885[0]: i2c bus 0 registered cx23885[0]: i2c bus 1 registered cx23885[0]: i2c bus 2 registered tveeprom 1-0050: full 256-byte eeprom dump: tveeprom 1-0050: 00: 20 00 13 00 00 00 00 00 2c 00 05 00 70 00 90 77 tveeprom 1-0050: 10: 50 03 05 00 04 80 00 08 0c 03 05 80 0e 01 00 00 tveeprom 1-0050: 20: 78 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: c0: 84 09 00 04 20 77 00 40 ec 66 25 f0 73 05 27 00 tveeprom 1-0050: d0: 84 08 00 06 fb 2c 01 00 90 29 95 72 07 70 73 09 tveeprom 1-0050: e0: 21 7f 73 0a 88 96 72 0b 13 72 10 01 72 11 ff 79 tveeprom 1-0050: f0: dc 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 tveeprom 1-0050: Tag [04] + 8 bytes: 20 77 00 40 ec 66 25 f0 tveeprom 1-0050: Tag [05] + 2 bytes: 27 00 tveeprom 1-0050: Tag [06] + 7 bytes: fb 2c 01 00 90 29 95 tveeprom 1-0050: Tag [07] + 1 bytes: 70 tveeprom 1-0050: Tag [09] + 2 bytes: 21 7f tveeprom 1-0050: Tag [0a] + 2 bytes: 88 96 tveeprom 1-0050: Tag [0b] + 1 bytes: 13 tveeprom 1-0050: Tag [10] + 1 bytes: 01 tveeprom 1-0050: Not sure what to do with tag [10] tveeprom 1-0050: Tag [11] + 1 bytes: ff tveeprom 1-0050: Not sure what to do with tag [11] tveeprom 1-0050: Hauppauge model 77051, rev E2F0, serial# 2451180 tveeprom 1-0050: MAC address is 00-0D-FE-25-66-EC tveeprom 1-0050: tuner model is Xceive XC5000 (idx 150, type 4) tveeprom 1-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88) tveeprom 1-0050: audio processor is CX23885 (idx 39) tveeprom 1-0050: decoder processor is CX23885 (idx 33) tveeprom 1-0050: has no radio cx23885[0]: hauppauge eeprom: model=77051 cx23885[0]: cx23885 based dvb card xc5000: Successfully identified at address 0x61 xc5000: Firmware has not been loaded previously DVB: registering new adapter (cx23885[0]) DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... cx23885_dev_checkrevision() Hardware revision = 0xb0 cx23885[0]/0: found at 0000:05:00.0, rev: 2, irq: 19, latency: 0, mmio: 0xd4000000 PCI: Setting latency timer of device 0000:05:00.0 to 64 When launching dvbscan I get the following in dmesg: xc5000: waiting for firmware upload (dvb-fe-xc5000-1.1.fw)... firmware: requesting dvb-fe-xc5000-1.1.fw kobject_add_internal failed for i2c-2 with -EEXIST, don't try to register things with the same name in the same directory. Pid: 8059, comm: kdvb-fe-0 Tainted: P 2.6.26-gentoo #11 Call Trace: [<ffffffff8036abb5>] kobject_add_internal+0x13f/0x17e [<ffffffff8036aff2>] kobject_add+0x74/0x7c [<ffffffff80230b02>] printk+0x4e/0x56 [<ffffffff803eb84a>] device_add+0x9b/0x483 [<ffffffff8036a876>] kobject_init+0x41/0x69 [<ffffffff803f059d>] _request_firmware+0x169/0x324 [<ffffffffa00e9a7e>] :xc5000:xc_load_fw_and_init_tuner+0x64/0x293 [<ffffffff804a7222>] i2c_transfer+0x75/0x7f [<ffffffffa00e53ad>] :s5h1409:s5h1409_writereg+0x51/0x83 [<ffffffffa00e9cea>] :xc5000:xc5000_init+0x3d/0x6f [<ffffffffa0091b0c>] :dvb_core:dvb_frontend_init+0x49/0x63 [<ffffffffa0092e2c>] :dvb_core:dvb_frontend_thread+0x78/0x2f0 [<ffffffffa0092db4>] :dvb_core:dvb_frontend_thread+0x0/0x2f0 [<ffffffff80240eaf>] kthread+0x47/0x74 [<ffffffff8022bc41>] schedule_tail+0x27/0x5b [<ffffffff8020be18>] child_rip+0xa/0x12 [<ffffffff80240e68>] kthread+0x0/0x74 [<ffffffff8020be0e>] child_rip+0x0/0x12 fw_register_device: device_register failed xc5000: Upload failed. (file not found?) xc5000: Unable to initialise tuner I have the firmware file located here: # ls -l /lib/firmware/dvb-fe-xc5000-1.1.fw -rw-r--r-- 1 root root 12332 Aug 31 12:56 /lib/firmware/dvb-fe-xc5000-1.1.fw If there is anything else I can provide (or try) to help debug, let me know, ...Patrick _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
