I cannot get my new HVR-1500Q to work at all even though it's recognized as such. The best I was able to figure out was it does not like the eeprom. After enabling the debug mode on tveeprom, I got the following when loading cx23885: cx23885 driver version 0.0.1 loaded cx23885 0000:05:00.0: enabling device (0000 -> 0002) ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 19 CORE cx23885[0]: subsystem: 0070:7790, board: Hauppauge WinTV-HVR1500Q [card=5,autodetected] cx23885[0]: i2c bus 0 registered cx23885[0]: i2c bus 1 registered cx23885[0]: i2c bus 2 registered tveeprom 1-0050: full 256-byte eeprom dump: tveeprom 1-0050: 00: 20 00 13 00 00 00 00 00 2c 00 05 00 70 00 90 77 tveeprom 1-0050: 10: 50 03 05 00 04 80 00 08 0c 03 05 80 0e 01 00 00 tveeprom 1-0050: 20: 78 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tveeprom 1-0050: c0: 84 09 00 04 20 77 00 40 ec 66 25 f0 73 05 27 00 tveeprom 1-0050: d0: 84 08 00 06 fb 2c 01 00 90 29 95 72 07 70 73 09 tveeprom 1-0050: e0: 21 7f 73 0a 88 96 72 0b 13 72 10 01 72 11 ff 79 tveeprom 1-0050: f0: dc 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 tveeprom 1-0050: Encountered bad packet header [ff]. Corrupt or not a Hauppauge eeprom. cx23885[0]: warning: unknown hauppauge model #0 cx23885[0]: hauppauge eeprom: model=0 cx23885[0]: cx23885 based dvb card xc5000: Successfully identified at address 0x61 xc5000: Firmware has not been loaded previously DVB: registering new adapter (cx23885[0]) DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... cx23885_dev_checkrevision() Hardware revision = 0xb0 cx23885[0]/0: found at 0000:05:00.0, rev: 2, irq: 19, latency: 0, mmio: 0xd4000000 PCI: Setting latency timer of device 0000:05:00.0 to 64 Did a hg pull -u http://linuxtv.org/hg/v4l-dvb earlier today so running off recent codebase. Any suggestions, ...Patrick _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
