Steven,
thanks for that. Sorry to take so long to respond,
business, sickness and a broken laptop belonging to the wife had
priority. I have made that change and it is still not working. Can
anyone tell me whether the "xc2028 2-0061: xc2028/3028 firmware name not
set!" is normal?
any help gratefully received.
Cheers Paul
dmesg is saying:
[ 28.638400] Linux agpgart interface v0.102
[ 28.718353] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x600
[ 28.718382] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x700
[ 29.581087] Linux video capture interface: v2.00
[ 29.826439] cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
[ 29.826815] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 19
[ 29.826825] ACPI: PCI Interrupt 0000:04:09.0[A] -> Link [LNKB] -> GSI
19 (level, low) -> IRQ 20
[ 29.826882] cx88[0]: subsystem: 107d:6654, board: LeadTek Winfast
DTV1800 Hybrid [card=65,autodetected]
[ 29.826884] cx88[0]: TV tuner type 71, Radio tuner type 0
[ 29.876688] cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
[ 30.712104] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 31.088959] parport_pc 00:06: reported by Plug and Play ACPI
[ 31.089080] parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 31.743004] cx88[0]: i2c register ok
[ 31.782451] cx88[0]/0: found at 0000:04:09.0, rev: 5, irq: 20,
latency: 64, mmio: 0xf7000000
[ 32.072372] tuner' 2-0061: chip found @ 0xc2 (cx88[0])
[ 32.072393] cx88[0]: tuner' i2c attach [addr=0x61,client=(tuner unset)]
[ 32.072397] xc2028: Xcv2028/3028 init called!
[ 32.072400] xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
[ 32.072403] xc2028 2-0061: xc2028_set_analog_freq called
[ 32.072405] xc2028 2-0061: generic_set_freq called
[ 32.072407] xc2028 2-0061: should set frequency 400000 kHz
[ 32.072409] xc2028 2-0061: check_firmware called
[ 32.072411] xc2028 2-0061: xc2028/3028 firmware name not set!
[ 32.081148] cx88[0]/0: registered device video0 [v4l2]
[ 32.081165] cx88[0]/0: registered device vbi0
[ 32.081181] cx88[0]/0: registered device radio0
[ 32.081241] xc2028 2-0061: xc2028_set_analog_freq called
[ 32.081244] xc2028 2-0061: generic_set_freq called
[ 32.081246] xc2028 2-0061: should set frequency 400000 kHz
[ 32.081248] xc2028 2-0061: check_firmware called
[ 32.081250] xc2028 2-0061: xc2028/3028 firmware name not set!
[ 32.082569] cx88[0]/2: cx2388x 8802 Driver Manager
[ 32.082591] ACPI: PCI Interrupt 0000:04:09.2[A] -> Link [LNKB] -> GSI
19 (level, low) -> IRQ 20
[ 32.082599] cx88[0]/2: found at 0000:04:09.2, rev: 5, irq: 20,
latency: 64, mmio: 0xf9000000
[ 32.083266] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 23
[ 32.083268] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI
23 (level, low) -> IRQ 16
[ 32.083287] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 32.127731] cx88/2: cx2388x dvb driver version 0.0.6 loaded
[ 32.127736] cx88/2: registering cx8802 driver, type: dvb access: shared
[ 32.127740] cx88[0]/2: subsystem: 107d:6654, board: LeadTek Winfast
DTV1800 Hybrid [card=65]
[ 32.127743] cx88[0]/2-dvb: cx8802_dvb_probe
[ 32.127745] cx88[0]/2-dvb: ->being probed by Card=65 Name=cx88[0],
PCI 04:09
[ 32.127747] cx88[0]/2: cx2388x based DVB/ATSC card
[ 32.156427] xc2028: Xcv2028/3028 init called!
[ 32.156433] xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
[ 32.156732] xc2028 2-0061: xc2028_sleep called
[ 32.169974] DVB: registering new adapter (cx88[0])
[ 32.169979] dvb_register_frontend
[ 32.169982] DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)...
[ 33.317397] NET: Registered protocol family 10
[ 33.317628] lo: Disabled Privacy Extensions
[ 33.712824] lp0: using parport0 (interrupt-driven).
[ 33.898837] Adding 1317288k swap on /dev/sda5. Priority:-1 extents:1
across:1317288k
[ 34.557544] EXT3 FS on sda1, internal journal
[ 37.102885] No dock devices found.
[ 37.531957] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3200+
processors (1 cpu cores) (version 2.20.00)
[ 37.531990] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8
[ 37.531992] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x8
[ 37.531994] powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12
[ 40.272294] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 40.272300] apm: overridden by ACPI.
[ 43.834306] eth0: no IPv6 routers present
[ 45.221024] dvb_frontend_open
[ 45.221032] cx88[0]/2-dvb: cx8802_dvb_advise_acquire
[ 45.221034] dvb_frontend_start
[ 45.223064] dvb_frontend_ioctl
[ 45.223071] dvb_frontend_thread
[ 45.223073] DVB: initialising frontend 0 (Zarlink ZL10353 DVB-T)...
[ 45.225411] dvb_frontend_release
[ 45.225415] cx88[0]/2-dvb: cx8802_dvb_advise_release
[ 45.225456] dvb_frontend_open
[ 45.225458] cx88[0]/2-dvb: cx8802_dvb_advise_acquire
[ 45.225459] dvb_frontend_start
[ 45.225462] dvb_frontend_ioctl
[ 45.225465] dvb_frontend_release
[ 45.225466] cx88[0]/2-dvb: cx8802_dvb_advise_release
[ 45.225505] dvb_frontend_open
[ 45.225507] cx88[0]/2-dvb: cx8802_dvb_advise_acquire
[ 45.225508] dvb_frontend_start
[ 45.225511] dvb_frontend_ioctl
[ 90.905975] Marking TSC unstable due to: cpufreq changes.
[ 90.913866] Time: acpi_pm clocksource has been installed.
[ 91.313691] Clocksource tsc unstable (delta = -204020896 ns)
[ 91.855061] xc2028 2-0061: xc2028_set_analog_freq called
[ 91.855073] xc2028 2-0061: generic_set_freq called
[ 91.855077] xc2028 2-0061: should set frequency 87500 kHz
[ 91.855081] xc2028 2-0061: check_firmware called
[ 91.855085] xc2028 2-0061: xc2028/3028 firmware name not set!
[ 91.870584] xc2028 2-0061: xc2028_sleep called
patch is:
--- cx88-cards.c.prepatch 2008-08-23 16:24:33.000000000 +1000
+++ cx88-cards.c 2008-08-31 18:26:01.000000000 +1000
@@ -1611,6 +1611,37 @@
} },
.mpeg = CX88_MPEG_DVB,
},
+ [CX88_BOARD_WINFAST_DTV1800H] = {
+ .name = "LeadTek Winfast DTV1800 Hybrid",
+ .tuner_type = TUNER_XC2028,
+// .radio_type = TUNER_XC2028,
+ .tuner_addr = 0x61,
+// .radio_addr = 0x61,
+ .input = {{
+ .type = CX88_VMUX_TELEVISION,
+ .vmux = 0,
+ .gpio0 = 0x0400, //pin 2:mute = 0 (off)
+ .gpio1 = 0x6040, //pin 13:audio = 0
(tuner), pin 14:FM = 1 (off?)
+ .gpio2 = 0x0000,
+ },{
+ .type = CX88_VMUX_COMPOSITE1,
+ .vmux = 1,
+ .gpio0 = 0x0400, //pin 2:mute = 0 (off)
+ .gpio1 = 0x6060, //pin 13:audio = 1
(line), pin 14:FM = 1 (off?)
+ .gpio2 = 0x0000,
+ },{
+ .type = CX88_VMUX_SVIDEO,
+ .vmux = 2,
+ }},
+ .radio = {
+ .type = CX88_RADIO,
+ .gpio0 = 0x0400, //pin 2:mute = 0 (off)
+ .gpio1 = 0x6000, //pin 13:audio = 0?
(tuner), pin 14:FM = 0? (on?)
+ .gpio2 = 0x0000,
+ },
+ .mpeg = CX88_MPEG_DVB,
+ },
+
};
/* ------------------------------------------------------------------ */
@@ -1948,6 +1979,11 @@
.subvendor = 0x14f1,
.subdevice = 0x8852,
.card = CX88_BOARD_GENIATECH_X8000_MT,
+ }, {
+ .subvendor = 0x107d,
+ .subdevice = 0x6654,
+ .card = CX88_BOARD_WINFAST_DTV1800H,
+
}
};
@@ -2310,6 +2346,15 @@
cx_set(MO_GP0_IO, 0x00000080); /* 702 out of reset */
udelay(1000);
break;
+ case CX88_BOARD_WINFAST_DTV1800H:
+ cx_set(MO_GP1_IO, 0x000010); //gpio 12 = 1: powerup XC3028
+ mdelay(250);
+ cx_clear(MO_GP1_IO, 0x000010); //gpio 12 = 0:
powerdown XC3028
+ mdelay(250);
+ cx_set(MO_GP1_IO, 0x000010); //gpio 12 = 1: powerup XC3028
+ mdelay(250);
+ break;
+
}
}
--- cx88-dvb.c.prepatch 2008-08-23 16:48:59.000000000 +1000
+++ cx88-dvb.c 2008-08-31 17:47:12.000000000 +1000
@@ -773,6 +773,7 @@
fe->ops.tuner_ops.set_config(fe, &ctl);
}
break;
+ case CX88_BOARD_WINFAST_DTV1800H:
case CX88_BOARD_PINNACLE_HYBRID_PCTV:
dev->dvb.frontend = dvb_attach(zl10353_attach,
&cx88_geniatech_x8000_mt,
--- cx88.h.prepatch 2008-08-23 16:49:16.000000000 +1000
+++ cx88.h 2008-08-24 18:28:22.000000000 +1000
@@ -220,6 +220,7 @@
#define CX88_BOARD_POWERCOLOR_REAL_ANGEL 62
#define CX88_BOARD_GENIATECH_X8000_MT 63
#define CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PRO 64
+#define CX88_BOARD_WINFAST_DTV1800H 65
enum cx88_itype {
CX88_VMUX_COMPOSITE1 = 1,
Steven Toth wrote:
> Paul Chubb wrote:
>> Hi,
>> a few months ago Miroslav Sustek created a patch for this card
>> against Markus Rechberger's v4l repository. This patch is attached as
>> dtv1800.patch. A patched and compiled set of drivers fails on ubuntu
>> hardy heron 8.04 with lots of symbol errors. Hardy is running
>> 2.6.24.19. I have attempted to backport this patch to the current v4l
>> tree with limited success. The driver loads however fails to do
>> anything useful. My patch is attached as dtv1800h-v4l.patch.
>>
>> I *think* the issue is with loading firmware. The tuner-xc2028.c
>> function check_firmware is passed a frontend without the firmware
>> name - producing the error shown in the dmesg listing below. If I
>> hack the function and hardcode the firmware file name, it attempts to
>> load the firmware but fails when it tries to read back.
>>
>> Now that I am totally out of my depth I am not sure what to try next.
>> Any help will be gratefully received.
>
> Don't call cx_write() inside the gpio card setup, you're potentially
> destroying the other bits, it's risky.
>
> + case CX88_BOARD_WINFAST_DTV1800H:
> + cx_write(MO_GP1_IO, 0x101010); //gpio 12 = 1: powerup XC3028
> + mdelay(250);
> + cx_write(MO_GP1_IO, 0x101000); //gpio 12 = 0: powerdown XC3028
> + mdelay(250);
> + cx_write(MO_GP1_IO, 0x101010); //gpio 12 = 1: powerup XC3028
> + mdelay(250);
> + break;
>
>
> Call cx_clear() and cx_set() instead, for the specific gpio bit (12)
> that you need.
>
> - Steve
>
>
>
>
>
--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
