Thanks. I got all the modules loaded, but lspci -vnn is still show it as unreconized. 02:00.0 Multimedia video controller [0400]: Conexant Unknown device [14f1:8880] (rev 0f) Subsystem: Hauppauge computer works Inc. Unknown device [0070:7801] Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at e9000000 (64-bit, non-prefetchable) [size=2M] Capabilities: <access denied> dmesg shows it as loading though. [ 37.521263] cx23885 driver version 0.0.1 loaded [ 37.605787] cx25840 0-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0) [ 37.608154] tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) [ 37.608176] wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) [ 37.746626] tuner-simple 0-0061: creating new instance [ 37.746629] tuner-simple 0-0061: type set to 50 (TCL 2002N) [ 37.747851] ivtv0: Registered device video0 for encoder MPG (4096 kB) [ 37.747872] ivtv0: Registered device video32 for encoder YUV (2048 kB) [ 37.747895] ivtv0: Registered device vbi0 for encoder VBI (1024 kB) [ 37.747915] ivtv0: Registered device video24 for encoder PCM (320 kB) [ 37.747917] ivtv0: Initialized card #0: Hauppauge WinTV PVR-150 [ 37.747932] ivtv: End initialization [ 37.748030] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17 [ 37.748040] PCI: Setting latency timer of device 0000:03:00.0 to 64 [ 37.748064] sky2 0000:03:00.0: v1.20 addr 0xe5000000 irq 17 Yukon-EC Ultra (0xb4) rev 2 [ 37.748420] sky2 eth0: addr 00:16:e6:d3:38:33 [ 37.748478] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 37.748484] PCI: Setting latency timer of device 0000:01:00.0 to 64 [ 37.748569] NVRM: loading NVIDIA UNIX x86 Kernel Module 173.14.12 Thu Jul 17 18:11:36 PDT 2008 [ 37.749928] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 37.749947] CORE cx23885[0]: subsystem: 0070:7801, board: Hauppauge WinTV-HVR1800 [card=2,autodetected] [ 37.930305] tuner' 1-0061: chip found @ 0xc2 (cx23885[0]) [ 37.932271] cx23885[0]: i2c bus 0 registered [ 37.959759] tuner' 2-0042: chip found @ 0x84 (cx23885[0]) [ 37.995903] tda829x 2-0042: could not clearly identify tuner address, defaulting to 60 [ 38.055821] tda18271 2-0060: creating new instance [ 38.074523] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 23 [ 38.074541] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 38.091286] TDA18271HD/C1 detected @ 2-0060 [ 39.257988] tda829x 2-0042: type set to tda8295+18271 [ 40.363430] cx23885[0]: i2c bus 1 registered [ 40.364411] cx25840' 3-0044: cx25 0-21 found @ 0x88 (cx23885[0]) [ 40.364782] cx23885[0]: i2c bus 2 registered [ 40.391559] tveeprom 1-0050: Hauppauge model 78521, rev C1E9, serial# 4851744 [ 40.391562] tveeprom 1-0050: MAC address is 00-0D-FE-4A-08-20 [ 40.391564] tveeprom 1-0050: tuner model is Philips 18271_8295 (idx 149, type 54) [ 40.391567] tveeprom 1-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88) [ 40.391569] tveeprom 1-0050: audio processor is CX23887 (idx 42) [ 40.391571] tveeprom 1-0050: decoder processor is CX23887 (idx 37) [ 40.391573] tveeprom 1-0050: has radio [ 40.391575] cx23885[0]: hauppauge eeprom: model=78521 [ 40.396523] cx23885[0]/0: registered device video1 [v4l2] [ 42.106808] cx25840' 3-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382 bytes) [ 42.120465] cx23885[0]: registered device video2 [mpeg] [ 42.120469] cx23885[0]: cx23885 based dvb card [ 42.197123] MT2131: successfully identified at address 0x61 [ 42.197127] DVB: registering new adapter (cx23885[0]) [ 42.197130] DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... [ 42.197333] cx23885_dev_checkrevision() Hardware revision = 0xb1 [ 42.197340] cx23885[0]/0: found at 0000:02:00.0, rev: 15, irq: 16, latency: 0, mmio: 0xe9000000 I have the HVR-1800 MCE kit edition Also another issue, don't know if this is mythtv relateed or drive related. When i set the card up in mythtv is /dev/video0 lets me choos television/s-video/composite whereas /dev/video1 is stuck on unset. Anything i can do to help? It's been ages since i've programmed, but i have a high learning curve. -----Original Message----- From: Steven Toth [mailto:stoth@xxxxxxxxxxx] Sent: Sunday, August 24, 2008 8:52 AM To: dcoates@xxxxxxxxxxxxxxxxxx Cc: linux-dvb@xxxxxxxxxxx Subject: Re: Hauppauge HVR-1800 Analog issues Dustin Coates wrote: > Any news on this? I bought this card but i noticed alot of people are > having problems with the anal nouge side of the card. I was wondering if > thier was any new developments. I've noticed a few posts but I'm not able to test or try and repro the problem. It sits on my todo list until I have a PCIe development system. - Steve _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
